It sounds crazy _but_ you can put a washer underneath the clip, and fatten up the mixture.....
@isaactadesse30852 күн бұрын
Thank you. Very informative! After almost 10 years, I’m about to tackle this project. You must be proud of your son😊
@fearfullmyth5 күн бұрын
Haha i do the same thing, then regret that i used a whole can of carb clean for gunked up oil
@oldsguy3545 күн бұрын
That needle does not adjust the idle speed. It's a mixture control needle. Raising or lowering the position of the needle changes what throttle position the carburetor can use the main jet for fuel and to what degree. If you want the engine to get on the main jet at a lower throttle position raise the needle, but make sure your engine can use the extra fuel at that rpm. If it can't, the engine will run poorly and become less efficient. The idle speed setting (if that carburetor has a non fixed idle speed) is a screw on the side that limits how far down the throttle slide can travel into the venturi.
@RbSauce96 күн бұрын
Add a Spacer to lift the needle off the seat under the clip.
@sidknee49755 күн бұрын
I was thinking exactly that. Couple of small washers or shims between the c clip and the housing. Back in the 70s and 80s we had to improvise everything from parts to tools as they either weren’t invented yet or to turn a $300 replacement in to a $10 fix.
@DaCat9817 күн бұрын
All Chinese motors are copied from something else. Find the carb by a good manufacturer, that was copied. Or just the needle.
@satisfactorycoffeestain30014 күн бұрын
IM NOT SURE but that looks like my dellorto vhsb 34 needle
@granthenderson88867 күн бұрын
Can’t thank you enough for this DIY video. Ordered the part of Amazon, got that in about two days. Used the video to complete the repair in under two hours. Saved me about $1000. Plus, keeps the old 2012 Toyota Sienna SE racking up the miles, about to surpass 200,000 miles this summer!
@boathemian76947 күн бұрын
i’ve got one of these
@joshwilcox89418 күн бұрын
Interesting little jeep!
@Jim-hp4le10 күн бұрын
great stuff bro. Love the diy get her done attitude. Well done!
@MikesGarageShop9 күн бұрын
Thanks 👍
@Jim-hp4le10 күн бұрын
at the end where you have the plunger and your considering a slide hammer, what if you re-threaded the rod into it and pulled it out with ur truck like u talked about earlier?
@andregilbert873811 күн бұрын
mine still has the bearings and still continues to pop off,any idea why?
@MikesGarageShop9 күн бұрын
Disconnect chain and see if there’s any play on the bearings. Otherwise make sure chain tension is correct.
@Michael-yi4mc13 күн бұрын
And please remove the baby from the van.
@user-gt3xx6lc1o13 күн бұрын
Lots of sketchy stuff here good idea to put a couple sizes bigger pilot jet in while working on carb. These engines are notoriously lean from factory for epa reasons and they start much easier with less choking.
@user-gt3xx6lc1o13 күн бұрын
That dark inboard spring looks to have too much slack in it as if its in wrong hole
@mrdanger485114 күн бұрын
Tells me you got an air leak
@rowdyazz751915 күн бұрын
Jets do nothing for idle
@jamessignorelli85220 күн бұрын
Do you drill the rivets very easy to do when you taking and read your own screws in where the rivets were very very simple
@cindylu215721 күн бұрын
Hello Mike, do you have a shop to do work or you just do this for KZread ? if you do what is your shop address. Thx Oh are you in Toronto Canada?
@USCG.Brennan21 күн бұрын
Mine quit working and it was only the battery.....EASY replacement! ;-)
@johngranato267322 күн бұрын
You might have not reached the right torque valve
@estysilva842522 күн бұрын
Where did you get the diagram
@suburbanbreakout982922 күн бұрын
Next time you take it off, it will reset your screwdriver
@kxngsparta430923 күн бұрын
aye bro thats some real talk bro
@elizabethbrown12824 күн бұрын
This video was excellent. I'm a mom of three young kids and I've never worked on a vehicle before. My van door broke, I found this video later that day and ordered the parts from the description box. and I was able to install the new cable in about an hour over nap time. Thank you!
@osmarpastorramoscastro945325 күн бұрын
Where is you shop?
@MikesGarageShop25 күн бұрын
Grand Haven, MI
@night892226 күн бұрын
My son kayo fox 70 was having issues and what I found was they set the carb for a certain elevation and there is no way to adjust it so they make you think. There is a plug on the carb and if you drill and pop out the plug there is a adj screw behind it. Thing runs great now.
@scottk277426 күн бұрын
Thanks so much Mike! I’m not mechanically inclined, but that really helps! I’ll definitely be looking for your videos when I need help. 👍
@WesBosАй бұрын
thanks a ton for this video! We had a 2015 sienna with a snapped cable. The dealership said it was covered under some sort of bulletin, but I opted just to replace it myself and not have the downtime of 2 days. Part was $90 CAD and it took me 45 mins to replace. One tip: The rear window trim piece can just bent bent back - plug it in first when you have slack in the cable, and then you don't need to remove the clip or the trim. Then plug the door side in. Def worth having a small or low profile ratchet, or an angled elbow to get into the tight spots.
@Still_I_RideАй бұрын
I tooky van to get repaired after a minor collision and it came back with a defective passenger door. It won't open automatically by pulling the handle out BUT, it opens from the key fob and overhead button. It will also close automatically from the handle, key fob and button. It's bizarre. Think it could be the cable or something else?
@visualflight4869Ай бұрын
Fast and easy explanation. Thanks for not wasting time with unnecessary nonsense.
@borroms97Ай бұрын
Thanks Mr. Mike for this guide. You saved me lots of time and effort. Cheers!
@MikesGarageShopАй бұрын
Wow thanks!
@dingdong7800Ай бұрын
Lil heat treatment get that thing back in running like new🥴
@whocarezbj6152Ай бұрын
Cpl mins
@johnbenson492Ай бұрын
I have a similar model, but mine doesn’t turn on at all, it just trips the outlet any ideas of what to do?
@MikesGarageShopАй бұрын
You have a direct short to ground inside the smoker. I’d pull the back off of it to find the short, it should be easy to find. A melted wire connector probably
@faschwankАй бұрын
Don't get that shit in your eyes.
@user-ui1ik8nf5gАй бұрын
Just finished installing on opposite door. All excellent tips. Thanks so much for posting!
@sajjadhashmi5449Ай бұрын
You are the man,how easily you have explained this difficult process. Great job,may Allah bless you and your family. Love from Brampton Ontario.
@motivatedmedic3852Ай бұрын
Worked great! Thanks for showing! Took about 2 hours start to finish. The last part you unscrewed below the window is actually not necessary if you hold off attaching the cable inside the door. Was also able to get the window piece off without snapping the plastic. Happy it worked so well! Thanks again!
@skatingclaybirdАй бұрын
What did you do?
@xptics7 күн бұрын
governor delete, you could also zip tie the spring and it has the same effect
@bryanabingart7362Ай бұрын
Thank you! I found I only needed to pry the rear end moulding up to remove the back anchor instead of removing/breaking it. Also helped when I started with the rear anchor. I didn’t need to remove the bracket that way. End with the 90° anchor since there’s just enough slack to snap it into place as the last step. Thank you for walking me through the steps without music and fluff!
@SquamingtonАй бұрын
Is that what those suction cups are for!!! They came with my valve spring compressor kit and I had no idea what they were for
@hiimholdin2397Ай бұрын
P c v purg
@blkwng81Ай бұрын
So i guess these are not a good quad to buy
@JeremiahBartolovichАй бұрын
Pin
@andretraversy9391Ай бұрын
Tank's
@EthanBoorenАй бұрын
"i know you KZreadrs" Loved that line, 😂 cause I've definitely done that with car videos before, stopping the video early because I'm pretty sure I've "got it from here" and been wrong. Also, Loved seeing the kids, it was very cute and wholesome seeing them help their dad out. Last thing, really great video, very concise into the point, and straight forward on how to do everything. Keep up the great work
@anthonypalumbo8171Ай бұрын
Toyota is providing additional coverage for repairs related to the power sliding door cable sub-assembly. beyond the 36 month warranty. See the following ink for details static.nhtsa.gov/odi/tsbs/2019/MC-10162786-9999.pdf No.: POL19-02. CUSTOMER SUPPORT PROGRAM BULLETIN (ZKD): COVERAGE FOR POWER SLIDING DOOR CABLE SUB- ASSEMBLY ON CERTAIN 2011-2018 MY SIENNA VEHICLES (VEHICLES EQUIPPED WITH POWER SLIDING DOORS ONLY)
@anthonypalumbo8171Ай бұрын
This is a link to to a technical service bulletin from Toyota to Power Sliding Door Cable Replacement. static.nhtsa.gov/odi/tsbs/2018/MC-10152554-9999.pdf Thank you for a very useful video. This is a link to another video on the same subject. kzread.info/dash/bejne/ZaN70c1_lLO0ZtI.html
Пікірлер
so excited for this! my cable snapped yesterday!
It sounds crazy _but_ you can put a washer underneath the clip, and fatten up the mixture.....
Thank you. Very informative! After almost 10 years, I’m about to tackle this project. You must be proud of your son😊
Haha i do the same thing, then regret that i used a whole can of carb clean for gunked up oil
That needle does not adjust the idle speed. It's a mixture control needle. Raising or lowering the position of the needle changes what throttle position the carburetor can use the main jet for fuel and to what degree. If you want the engine to get on the main jet at a lower throttle position raise the needle, but make sure your engine can use the extra fuel at that rpm. If it can't, the engine will run poorly and become less efficient. The idle speed setting (if that carburetor has a non fixed idle speed) is a screw on the side that limits how far down the throttle slide can travel into the venturi.
Add a Spacer to lift the needle off the seat under the clip.
I was thinking exactly that. Couple of small washers or shims between the c clip and the housing. Back in the 70s and 80s we had to improvise everything from parts to tools as they either weren’t invented yet or to turn a $300 replacement in to a $10 fix.
All Chinese motors are copied from something else. Find the carb by a good manufacturer, that was copied. Or just the needle.
IM NOT SURE but that looks like my dellorto vhsb 34 needle
Can’t thank you enough for this DIY video. Ordered the part of Amazon, got that in about two days. Used the video to complete the repair in under two hours. Saved me about $1000. Plus, keeps the old 2012 Toyota Sienna SE racking up the miles, about to surpass 200,000 miles this summer!
i’ve got one of these
Interesting little jeep!
great stuff bro. Love the diy get her done attitude. Well done!
Thanks 👍
at the end where you have the plunger and your considering a slide hammer, what if you re-threaded the rod into it and pulled it out with ur truck like u talked about earlier?
mine still has the bearings and still continues to pop off,any idea why?
Disconnect chain and see if there’s any play on the bearings. Otherwise make sure chain tension is correct.
And please remove the baby from the van.
Lots of sketchy stuff here good idea to put a couple sizes bigger pilot jet in while working on carb. These engines are notoriously lean from factory for epa reasons and they start much easier with less choking.
That dark inboard spring looks to have too much slack in it as if its in wrong hole
Tells me you got an air leak
Jets do nothing for idle
Do you drill the rivets very easy to do when you taking and read your own screws in where the rivets were very very simple
Hello Mike, do you have a shop to do work or you just do this for KZread ? if you do what is your shop address. Thx Oh are you in Toronto Canada?
Mine quit working and it was only the battery.....EASY replacement! ;-)
You might have not reached the right torque valve
Where did you get the diagram
Next time you take it off, it will reset your screwdriver
aye bro thats some real talk bro
This video was excellent. I'm a mom of three young kids and I've never worked on a vehicle before. My van door broke, I found this video later that day and ordered the parts from the description box. and I was able to install the new cable in about an hour over nap time. Thank you!
Where is you shop?
Grand Haven, MI
My son kayo fox 70 was having issues and what I found was they set the carb for a certain elevation and there is no way to adjust it so they make you think. There is a plug on the carb and if you drill and pop out the plug there is a adj screw behind it. Thing runs great now.
Thanks so much Mike! I’m not mechanically inclined, but that really helps! I’ll definitely be looking for your videos when I need help. 👍
thanks a ton for this video! We had a 2015 sienna with a snapped cable. The dealership said it was covered under some sort of bulletin, but I opted just to replace it myself and not have the downtime of 2 days. Part was $90 CAD and it took me 45 mins to replace. One tip: The rear window trim piece can just bent bent back - plug it in first when you have slack in the cable, and then you don't need to remove the clip or the trim. Then plug the door side in. Def worth having a small or low profile ratchet, or an angled elbow to get into the tight spots.
I tooky van to get repaired after a minor collision and it came back with a defective passenger door. It won't open automatically by pulling the handle out BUT, it opens from the key fob and overhead button. It will also close automatically from the handle, key fob and button. It's bizarre. Think it could be the cable or something else?
Fast and easy explanation. Thanks for not wasting time with unnecessary nonsense.
Thanks Mr. Mike for this guide. You saved me lots of time and effort. Cheers!
Wow thanks!
Lil heat treatment get that thing back in running like new🥴
Cpl mins
I have a similar model, but mine doesn’t turn on at all, it just trips the outlet any ideas of what to do?
You have a direct short to ground inside the smoker. I’d pull the back off of it to find the short, it should be easy to find. A melted wire connector probably
Don't get that shit in your eyes.
Just finished installing on opposite door. All excellent tips. Thanks so much for posting!
You are the man,how easily you have explained this difficult process. Great job,may Allah bless you and your family. Love from Brampton Ontario.
Worked great! Thanks for showing! Took about 2 hours start to finish. The last part you unscrewed below the window is actually not necessary if you hold off attaching the cable inside the door. Was also able to get the window piece off without snapping the plastic. Happy it worked so well! Thanks again!
What did you do?
governor delete, you could also zip tie the spring and it has the same effect
Thank you! I found I only needed to pry the rear end moulding up to remove the back anchor instead of removing/breaking it. Also helped when I started with the rear anchor. I didn’t need to remove the bracket that way. End with the 90° anchor since there’s just enough slack to snap it into place as the last step. Thank you for walking me through the steps without music and fluff!
Is that what those suction cups are for!!! They came with my valve spring compressor kit and I had no idea what they were for
P c v purg
So i guess these are not a good quad to buy
Pin
Tank's
"i know you KZreadrs" Loved that line, 😂 cause I've definitely done that with car videos before, stopping the video early because I'm pretty sure I've "got it from here" and been wrong. Also, Loved seeing the kids, it was very cute and wholesome seeing them help their dad out. Last thing, really great video, very concise into the point, and straight forward on how to do everything. Keep up the great work
Toyota is providing additional coverage for repairs related to the power sliding door cable sub-assembly. beyond the 36 month warranty. See the following ink for details static.nhtsa.gov/odi/tsbs/2019/MC-10162786-9999.pdf No.: POL19-02. CUSTOMER SUPPORT PROGRAM BULLETIN (ZKD): COVERAGE FOR POWER SLIDING DOOR CABLE SUB- ASSEMBLY ON CERTAIN 2011-2018 MY SIENNA VEHICLES (VEHICLES EQUIPPED WITH POWER SLIDING DOORS ONLY)
This is a link to to a technical service bulletin from Toyota to Power Sliding Door Cable Replacement. static.nhtsa.gov/odi/tsbs/2018/MC-10152554-9999.pdf Thank you for a very useful video. This is a link to another video on the same subject. kzread.info/dash/bejne/ZaN70c1_lLO0ZtI.html