Пікірлер

• 
  @aguilarg228 күн бұрын

  Great UDS build! How deep are the two grates?

• 
  @OptimisticGarage8 күн бұрын

  Thanks. Grates are 6” and 12” from the top

• 
  @Whalermansteve8423 күн бұрын

  Ouch. Looks rough , hope you are able to weld. I’m working on a 19 ft camper trailer frame as we speak. Putting new boards down. So much labor lol

• 
  @OptimisticGarage22 күн бұрын

  Lots of labor however very rewarding in the end. Yes I welded lots of new iron to mine. Good luck.

• 
  @wayneswonderarium23 күн бұрын

  Leaving the nut on and wailing the nut would help the mushrooming 😅

• 
  @YingMoua-lp2tn29 күн бұрын

  Very nice but the meat turn out great. Did you had to burn the inside paint, sand, and wash it to make it clean for safety?

• 
  @OptimisticGarage29 күн бұрын

  Yes fill it with wood and burn for a few hours. All the interior exterior paint will burn off. Then wire wheel everything. Once complete you have a bare metal barrel. Use a high temp paint to coat the outside and spray Pam or olive oil on inside to prevent rust. Once you start using it you will build up a nice char inside that protects metal

• 
  @YingMoua-lp2tn29 күн бұрын

  @@OptimisticGarage Thank you. Can’t wait to get myself one to work on.

• 
  @ChariotLogisticsАй бұрын

  where did u buy the new muffler tail pipe ? I got 2016 like yours the only issue i have is the tail pipe make some noise

• 
  @OptimisticGarageАй бұрын

  Nameless performance is where I got the muffler.

• 
  @kenjuicekrajewski9577Ай бұрын

  So im doing pre mix on the one i picked up so what cable did you use as the junction box and short cable removed now the throttle cable is to short?? Ideas on what you did thanks

• 
  @OptimisticGarageАй бұрын

  If I remember correctly I didn’t change anything with the throttle. Simply removed the gear on the end of the pump so it wouldn’t spin. Also plug the outlet side of the pump so no dirt gets in there

• 
  @kenjuicekrajewski9577Ай бұрын

  @@OptimisticGarage mmmm yes off the gear the short 12 inch cable connects to the top of carb il have to do some research on bikebandit and ebay cables thanks

• 
  @OptimisticGarageАй бұрын

  Everything is hooked back as it was before removing gear off oiler. Therefore no new cables needed. If it worked before removing gear it should work now. Just checked mine. Looks completely stock

• 
  @kenjuicekrajewski9577Ай бұрын

  @@OptimisticGarage great i saved the other cables il have to check them thanks again

• 
  @PMB8272 ай бұрын

  Gosh, I really want one of these! There’s one for $400 in my area on Facebook marketplace, but I won’t have the cash until the end of the week. Hope someone doesn’t beat me to it! 😢 the guy selling it rebuilt it

• 
  @OptimisticGarage2 ай бұрын

  Sounds like a fair price. I know the feeling of waiting and crossing your fingers. Hope it works out. Thx for watching

• 
  @PMB827Ай бұрын

  @@OptimisticGarage someone beat me to it but I ended getting a mini bike :)

• 
  @OptimisticGarageАй бұрын

  @@PMB827 what mini bike did you get? Older or newer model. I love some of the original 70’s bikes

• 
  @PMB827Ай бұрын

  @@OptimisticGarage I got a used db30 doodlebug. I think it’s modern, though a few years old. I might end up trading it for a vintage if I get lucky enough!

• 
  @HuyLe-vt2bz2 ай бұрын

  Once it’s up to operating temp, you opened your fill plug - did much come out afterwards? Let it drain out until it stops, then tighten the bolt, then you’re done?

• 
  @OptimisticGarage2 ай бұрын

  Opened up drain plug after heated up and went through gears. It took another 3 to 5 oz then it was full

• 
  @HuyLe-vt2bz2 ай бұрын

  Copy thanks. The forums make it sound like you shouldn’t diy this.

• 
  @OptimisticGarage2 ай бұрын

  @@HuyLe-vt2bz no problem that’s what the car community is all about. Helping each other. Good luck.

• 
  @humanoid77652 ай бұрын

  I have this exact machine and I just got it playing again. This machine hasnt been played in over 35 yrs. Ive always wanted to get it running and decided to start working on it. Ive replaced the rectifier board and repinned the molex connectors to the rectifier board, I also replaced the mpu-200 and sb-300 boards with nvram boards, replaced the solenoid driver board with an alltek board. Im about to replace the lamp driver board with an alltek driver board and ordered an LED kit for the machine as well. I need to get new score displays as well but have been thinking about getting blue displays instead of the stock amber ones. I was looking for a set of direct replacement ones that come pre-assembled.

• 
  @OptimisticGarage2 ай бұрын

  Careful with led lighting in these old games. Sometimes looks off but it’s personal preference too. I recommend clear coating the backside of the back glass to keep it from flaking off. Also led in back glass simply to reduce the heat. Love the game. Have you seen the short video from the 80’s about this game. Search on KZread it’s kinda neat.

• 
  @humanoid77652 ай бұрын

  @OptimisticGarage The backglass is already flaking before I even touched it LOL. I'm sure this kit will be way better than the bulbs in it now. A lot of them have flaky sockets and corroded sockets as well. Going to try and use a dremel and 443 wire brush bits to clean them. I have seen a few videos on the galaxy and I found out that the galaxy was the first machine to introduce seperate general illumination (GI) system and Williams came out of retirement and built a few pinball machines for stern and galaxy was one of them.

• 
  @OptimisticGarage2 ай бұрын

  @@humanoid7765 awesome. Glad to know there are still people out there saving on these old games. Good luck 👍🏼

• 
  @humanoid77652 ай бұрын

  @@OptimisticGarage Ditto 👌👍👏

• 
  @dustinlampston76182 ай бұрын

  Whoever allowed you to use a paint gun should be charged with a felony YOU FN SUCK!!!

• 
  @craigrice38872 ай бұрын

  I would add some tie down points in the floor for future use and a tool box on the tong ,you could add some angle or strapping to the tong and lay the spare flat on it and bolt it

• 
  @OptimisticGarage2 ай бұрын

  Tie downs are a must. Been putting spare in tow vehicle

• 
  @wayneswonderarium2 ай бұрын

  Air matresses: when you want to sleep on the ground but not right away 😅

• 
  @OptimisticGarage2 ай бұрын

  Exactly

• 
  @michaelbrown-zi6ev2 ай бұрын

  i wouldve painted the wood floor and sides black as well plus it would last longer or use old engine oil mix a little diesel stain it thats nearly free

• 
  @OptimisticGarage2 ай бұрын

  I’ve never tried the engine oil before. Might do that in the future. Free is good. Thx

• 
  @KenMrKLC2 ай бұрын

  The way you speak on video reminds me of VGG … you must watch him?

• 
  @OptimisticGarage2 ай бұрын

  Haha that’s hilarious. I love watching Derek best channel on KZread in my opinion.

• 
  @OptimisticGarage3 ай бұрын

  Yes. Boys used it and brakes were sub par. I’m looking into a different brake pad shape. Issue is limited amount of pad actually making contact to hub. I will try and get a short updated posted when weather turns better.

• 
  @bilboko883 ай бұрын

  Any updates my guy??

• 
  @StratOvation3 ай бұрын

  Check out John McK 47 video library here on KZread for some basic safety information on these heaters. You're definitely going to need to get the combustion exhaust and intake routed outside this case or you will certainly melt down the plastic , wiring and circuitry. That exhaust will be >500F when running on high. The exhaust should be routed on a descending path to allow the condensate to drain or it will corrode from the carbonic acid in the condensate. kzread.info/dash/bejne/mWRr27iuisXQo6g.html

• 
  @SalvoDan3 ай бұрын

  There is a funny thing about Tyre Sizes; They are measured in millimetres, inches and a ratio. 205(mm)/75(%)R15 have a smaller diameter (689mm/27.13") than 235/75R15 tyres (734mm/28.94"). This will give you (about) one extra inch of ride height and give you (about) one less inch of clearance to the fender/mudguard). It will (obviously) also affect the width of the wheel in the guard, but also the unsprung weight.

• 
  @SalvoDan3 ай бұрын

  I like the idea of a central beam running all the way from the hitch/coupling to the rear tie bar/crossmember. A single length of RHS (rectangular hollow section) is the most convenient and if it has a 50mm ID (internal dimension), it could also function as a hitch receiver for a bike rack or recovery point. It is an easy retrofit that gives a little bit of extra strength to a DIY repaired trailer, while adding only a little bit of extra weight. It also provides a much safer cable run for the electrics, and the hitch receiver at the end provides a central tie-down/recovery point if something bad happens to your trailer.

• 
  @OptimisticGarage3 ай бұрын

  Brilliant idea and will consider this spring.

• 
  @1MajorTom3 ай бұрын

  in order for it not to be dangerous to use, you will have to get the exhaust and the muffler out of the box. and get the rest of the exhaust heat-safe in the box with the heat-safe the exhaust pipe otherwise it will all end up burning down. as the exhaust before the muffler becomes red hot and the muffler also gets very very hot, I have installed many of those heaters in trucks and buses, and most of the times that they burn the buses off is because someone (not knowledgeable) has installed them incorrectly behind the bus. so diesel and engine oil have come out all over the exhaust and muffler (so every winter it has been a big firebomb they have lit underneath)😊 . but keep on with the ideas!😊

• 
  @OptimisticGarage3 ай бұрын

  Excellent thanks for the tips. I have noticed the heat on exhaust during testing.

• 
  @1MajorTom3 ай бұрын

  @@OptimisticGarage you're welcome😁 we must help each other as best we can🙂

• 
  @ejtakach3 ай бұрын

  Very ingenious, keep on with the ideas!

• 
  @OptimisticGarage3 ай бұрын

  Thanks man!

• 
  @kenjuicekrajewski95773 ай бұрын

  Theres 15 for sale now in ct and mass fb market i just bought a sweet running one yesterday for $300 and ordered $200 in mods lol

• 
  @OptimisticGarage3 ай бұрын

  Sweet deal. Enjoy!

• 
  @johnkidder4403 ай бұрын

  Ya Take $300 For it

• 
  @OptimisticGarage3 ай бұрын

  Not for sale

• 
  @davidruiz53833 ай бұрын

  Great project but what prior contents or liquids were inside the drum. Thanks and God Bless.

• 
  @OptimisticGarage3 ай бұрын

  It was used for soy oil. I got it from a large bakery factory. Thanks 🙏

• 
  @noahmeme23 ай бұрын

  I might buy one of these. Someone is selling a modified 60cc one on Facebook for $1,000.

• 
  @OptimisticGarage3 ай бұрын

  It’s a very reliable machine stock. Also very slow compared to today’s standards. 25mph. I don’t know much about the aftermarket bore kits. I would see if they still have original parts with it so you can fall back on them if and when the Chinese aftermarket parts fail

• 
  @noahmeme23 ай бұрын

  @@OptimisticGarage The seller is ignoring me, they read my message and didn't say anything. I'm guessing someone else beat me to it.

• 
  @derricksmiley56324 ай бұрын

  My air vents was made out of fence post 90° in up then put fence cap on n off for air flow 😂i damn near build minds for pennies on the dollar..An den put a rosstisre on it later

• 
  @oby-16074 ай бұрын

  I got fed up after replacing the vacuum pump a couple of times and no fuel draw. Installed an electric fuel pump low pressure from Amazon and now it starts every time. I do have a large fuel filter coming from the tank and a smaller one just before the carb. Starts even in the cold even with no choke. Before this, even with starting fluid (ether) it wouldn't start. Now I run only ethanol free gas as well. A litlle more money but makes for peace of mind. Debris floating around in your tank can cause havoc with plugging fuel lines as well.

• 
  @OptimisticGarage4 ай бұрын

  I have an old hose and primer bulb from a boat. Gonna throw that on it I think. What model fuel pump did you go with on yours?

• 
  @oby-16074 ай бұрын

  @@OptimisticGarage It was just a low pressure, 2-4 pounds pressure pump from Amazon. Make sure it is low pressure and not above 4 pounds.

• 
  @sheilamclaughlin9634 ай бұрын

  Haul the spare in the tow vehicle

• 
  @OptimisticGarage4 ай бұрын

  Thanks so much for watching!

• 
  @sheilamclaughlin9634 ай бұрын

  Paint the hub blue

• 
  @sheilamclaughlin9634 ай бұрын

  Need 1 1/2 strap top and bottom

• 
  @user-sh3ms1hw5p4 ай бұрын

  keep it in your yard for for small yard work never pass dot inspt for hwy use ps did ya get that trailer 4 free

• 
  @OptimisticGarage4 ай бұрын

  No dot inspection needed it’s under 26000# and not commercial use. Been great little trailer. Thanks for watching.

• 
  @user-sh3ms1hw5p4 ай бұрын

  keep up the good work

• 
  @wayneswonderarium4 ай бұрын

  1:53 zip ties! 😂

• 
  @StaunchRobots4 ай бұрын

  Hey man love this, the one part i am looking for you didnt list.... where did you get that clamp for your lid, not the main hinge the support one, :)

• 
  @OptimisticGarage4 ай бұрын

  Thanks appreciate it. Sorry yeah the lid clamp was from the jungle website. I just added it to the description. Thanks for the support.

• 
  @travharrell17135 ай бұрын

  NEVER put automobile oil in atv or sxs with a wet clutch. It has addtives that will kill your clutch

• 
  @OptimisticGarage5 ай бұрын

  Thanks for the info

• 
  @lafaina795 ай бұрын

  Great project but I don't understand why cutting corners on paint job after all the effort you put on?

• 
  @OptimisticGarage5 ай бұрын

  Yeah paint’s expensive and I’m definitely not a painter. Probably my least favorite thing to do. Thanks for watching

• 
  @user-ul3vu4ks2p6 ай бұрын

  standing out in my 22x24 garage with 2 diesel JD lawn mowers in my way,homemade woodstove is putting out great heat! Had to clean out the carb on my pressure washer last weekend-ethanol is a killer! FYI-I'm a welder for my paycheck

• 
  @OptimisticGarage6 ай бұрын

  Sounds like a nice setup.

• 
  @user-ul3vu4ks2p6 ай бұрын

  @@OptimisticGarage I need to figure out how to heat my house with wood,my homemade stove is great for the garage but not efficient enough for the house!

• 
  @OptimisticGarage6 ай бұрын

  @@user-ul3vu4ks2p I’ve been interested in those rocket style wood stoves. Possibly to heat a shed

• 
  @user-ul3vu4ks2p6 ай бұрын

  @@OptimisticGarage Mine is no 'rocket', it's a piece of 20inch .375 wall that I built a stove out of! but it heats my shop just fine. It burns oil filters,tires, and and anything flamable!!

• 
  @ghanasr6 ай бұрын

  Looks like you are using a 3 ton jack stand pulling all the way up. This is dangerous. I would use double locking 6 ton jack stand.

• 
  @OptimisticGarage6 ай бұрын

  I’m looking at them. Any you recommend?

• 
  @theloghomeguy33796 ай бұрын

  Is that plastic or fiberglass

• 
  @OptimisticGarage6 ай бұрын

  Fiberglass on these old sleds.

• 
  @user-bh3je8ud8h6 ай бұрын

  Great work thus far. Gotta get a clutch for that great old Cat.

• 
  @OptimisticGarage6 ай бұрын

  Thankyou. Clutch and seat cover on the list

• 
  @nathenexplosion80086 ай бұрын

  I know whats wrong with it. It needs gas 😂😂 Just joking around

• 
  @OptimisticGarage6 ай бұрын

  Ya know one might be surprised on what a fellar will miss. Haha. Going through fuel system next. Thanks for watching.

• 
  @shanepettit68726 ай бұрын

  Who gives a 💩

• 
  @DrAAgon216 ай бұрын

  Winter is coming…

• 
  @OptimisticGarage6 ай бұрын

  Yes sir! Long way to go on this build but fun project so far.

• 
  @wayneswonderarium6 ай бұрын

  When you're pushing hard remember to open your hand and push with a flat palm, to help avoid those busted knuckles 😅

• 
  @OptimisticGarage6 ай бұрын

  Yeah I know better.

• 
  @wayneswonderarium7 ай бұрын

  Always l love seeing restoration vids 🤩

• 
  @esparza40oz7 ай бұрын

  Do you have a link to the lid locki mechanism

• 
  @OptimisticGarage7 ай бұрын

  www.amazon.com/LavaLock®-LL-12050-Smoker-Vertical-Handle/dp/B074TQNX88

• 
  @TheCuylerCrew7 ай бұрын

  I’ve made homage applesauce with it

• 
  @TheCuylerCrew7 ай бұрын

  Yes it is

• 
  @TheCuylerCrew7 ай бұрын

  I have the same thing

• 
  @OptimisticGarage7 ай бұрын

  Simple machine but kinda neat and it works great!

• 
  @Kmclemore7 ай бұрын

  I have this in my cart now

• 
  @OptimisticGarage7 ай бұрын

  I’ve been using it without any issues.

• 
  @sambrewer23068 ай бұрын

  Take ur time. Like u are. I can already tell Jr. Is going to make a masterpiece. 👏

• 
  @OptimisticGarage8 ай бұрын

  Thank you