Пікірлер

• 
  @Divine2pac13 күн бұрын

  Hi I'm Divine do you still have some of those

• 
  @rapidstu0113 күн бұрын

  @@Divine2pac I still have lots of parts, what parts are you after?

• 
  @jeffspears88012 ай бұрын

  Worthless video

• 
  @karlvanboxel5612 ай бұрын

  Those bloody fzr1000 and 750 engines make some shit sounds!! It’s all because Yamaha were too slack to put a alternator / starter chain tensioner in there. Other manufacturers do it Kawasaki and Honda Suzuki have the best idea. IMO in they dive the alternator off the clutch basket on some model( RF 900) and the starter is next door set of gears and a sprag clutch simple this gives them a nice 6 brg crank with out all the piss on if another chain buried deep and in yamahas case a noisey bastard Glad they sorted it on the R ones!?

• 
  @karlvanboxel5616 ай бұрын

  The best way to check the diaphragms is to stretch them over a brite light

• 
  @karlvanboxel5616 ай бұрын

  R the emulsion tubes removable in these carbs?

• 
  @rapidstu016 ай бұрын

  Yes they are. 👍

• 
  @adanlopez53527 ай бұрын

  very good vid, thanks a lot

• 
  @jamiegurner31727 ай бұрын

  thanks for sharing. i have my dads sat in the garage which have brought back to life, so i will look on your website. cheers

• 
  @AhmedSalah-do6fn8 ай бұрын

  😂😂😂

• 
  @A.e.j91959 ай бұрын

  😆😆

• 
  @A.e.j91959 ай бұрын

  😭😭😭

• 
  @user-vb8tj7wx9g10 ай бұрын

  Is it necessary to lessen cam shaft bolts or the 4 cam phase bolts?

• 
  @vroums7610 ай бұрын

  Great job ,hope you will have fun on road with this granny bike, i have a vfr RC 36 II, so i understand what you feel with this kind of bike 🙂

• 
  @andywilson381310 ай бұрын

  Hi Stuart what size pipes do you use is it m5 or m6 ? Can u recommend a link👍

• 
  @rapidstu0110 ай бұрын

  I'm sure they are m5, tho I use short ones I have bought a selection from eBay as they are fairly cheap, it's the same with the rubber caps I use.

• 
  @rapidstu0110 ай бұрын

  I just checked my eBay purchase history and the last ones a bought were M6 brass barbs with rubber covers. I will look on my restoration bike this week and confirm.

• 
  @andywilson381310 ай бұрын

  @@rapidstu01 appreciate that many thanks👍

• 
  @rapidstu0110 ай бұрын

  Definitely M6 on my latest project

• 
  @andywilson381310 ай бұрын

  @@rapidstu01 thank you will order some makes sense 👍

• 
  @rapidstu01 Жыл бұрын

  I have sorted out 2 cam sprockets , send me your email and I'll send a picture to make sure its what you need, my email is [email protected] Cheers

• 
  @hugobenitez5845 Жыл бұрын

  I need the sprockets 2 of them. With the #7 on it

• 
  @rapidstu01 Жыл бұрын

  The sprockets are interchangeable, I fitted two new ones when I changed my camchain, I still have my original ones that are perfectly usable. What is wrong with yours?

• 
  @hugobenitez5845 Жыл бұрын

  @@rapidstu01 one is cracked where the pin is at the other has a oval in the pin hole so it has a little bit of play and it's cracked as well just got surgery done so I can't afford them

• 
  @rapidstu01 Жыл бұрын

  @@hugobenitez5845 I will have a sort out at the weekend, I probably have a pair of sprockets you can have, text me a reminder on Friday night so I don't forget, I don't want any money for them. If you are not UK I'll probably need postage.

• 
  @hugobenitez5845 Жыл бұрын

  @@rapidstu01 its friday night

• 
  @aligningpurposes268 Жыл бұрын

  What happens if you line the circle and ovals oppositely? Will it prevent chain from spinning?

• 
  @rapidstu01 Жыл бұрын

  The chain will spin but the cam timing will be wrong, you may wreck the engine, pistons hitting valves. I stick to the recommended build procedure. Thank you for watching the video.

• 
  @KubilaySavs Жыл бұрын

  How to get stabbed 101

• 
  @yinyangyin Жыл бұрын

  i like your bikes . . . . . . but I'm liking that jeet kune do tee shirt even more. rip bruce. 🏴‍☠️

• 
  @rapidstu01 Жыл бұрын

  Thank you 👍 and I am going to be adding some jkd based self defense videos soon.

• 
  @chrisreed8525 Жыл бұрын

  If you have a weak mix on the front cylinders and you flow it for more airflow, you’ll get an even weaker mix! Nice polishing and porting by the way 👍

• 
  @rapidstu01 Жыл бұрын

  My mistake, and you are right, I should have said poor air flow! But thanks for watching, and commenting, I'm still learning

• 
  @everything4053 Жыл бұрын

  You made everything seem so easy but I understand it alot more cause of you’re detailed vid. Going to be replacing my gallery gaskets and was a bit intimidated with the timing part but seems easy, thank you

• 
  @chrisreed8525 Жыл бұрын

  I really meant fit flexible tubes (capped off) permanently so that you don’t have to fiddle under the carbs to fit your gauges 👍

• 
  @rapidstu01 Жыл бұрын

  My misunderstanding 👍

• 
  @chrisreed8525 Жыл бұрын

  You’re better off fitting some tubes to the adaptors and plug them and leave them fitted for future use, this set up is fitted as standard to some of the Thunderaces and is far less fiddly to use with the carbs fitted.

• 
  @rapidstu01 Жыл бұрын

  I have a set of tubes that came with my old vacuum gauges, they are easier to fit but do not have barbs like the ones I have used. I prefer the barbs so the plugs can't work loose. But it is an option I should have mentioned. Thanks for mentioning it 👍

• 
  @COBRAcz23 Жыл бұрын

  @@rapidstu01 what adapters you buy ? I will have to again balance my carbs , last time when it was in garage i pay heavy price for works so i decide tu buy Vacuum Synchronizer and i have to buy those and leave them permanently , because this is really nightmare .

• 
  @rapidstu01 Жыл бұрын

  @@COBRAcz23 I can't post a picture on here but the adapters are very cheap and on ebay. I believe they are called M6 brass vacuum adapters, or M5 vacuum adapters, depending on the thread on yours. If you look at my earlier videos I think I show them. I hope this helps

• 
  @COBRAcz23 Жыл бұрын

  @@rapidstu01 i think i found them , well i will see if it is M6 or M5 i will have to clean carbs and balance them them after that so I put those in to the air intakes so next balance will be much easier .

• 
  @chrisreed8525 Жыл бұрын

  Those diaphragms, are they the cheap eBay ones that can be had for less than £10 the set? They’re listed as having an outside diameter of 69mm, but I’m sure I measured mine as 75mm diameter, I assume they still fit? Thanks 👍

• 
  @rapidstu01 Жыл бұрын

  No they are £20 a set and the correct size 👍

• 
  @natanmortenfeld5813 Жыл бұрын

  Thanks you are the best, looking forward to see your carb sync video,there are some carb sync videos out there, but non devoted especially to our beloved Yamaha fzr1000 , so looking forward to watching it .

• 
  @midnightmoves7976 Жыл бұрын

  Great work, looks like its a lovely warm place to assemble an engine :D. You may want to check the clearance of those exhaust manifolds, I got the same style on mine and they fowl on the steering column and need a little dent put in them.

• 
  @rapidstu01 Жыл бұрын

  Thanks it's better than the workshop 👍 and the Malian headers were a pig, the original fixing holes needed enlarging, I got away with linishing the steering u.j. smooth, and rounding edges of, got a whole 5mm of clearance now 👍

• 
  @midnightmoves7976 Жыл бұрын

  @@rapidstu01 I also had to widen the fixing holes.

• 
  @aligningpurposes268 Жыл бұрын

  Im doing the timing chain on maxima. As I was taking the old crank shaft sprocket out. The pin fell off as well. Where the sprocket slides into. Is that normal? It doesn’t look like it was welded on.

• 
  @wibbleplays6202 Жыл бұрын

  Sounds broken mate!! Don't run it like this it will get more damage

• 
  @rapidstu01 Жыл бұрын

  That's the dry clutch, which is new! Running it in the dining room exaggerates the sound, but believe me the motor is great.

• 
  @jessalyn5241 Жыл бұрын

  𝓟Ř𝔬𝓂𝔬𝐒ϻ

• 
  @midnightmoves7976 Жыл бұрын

  Good work mate.

• 
  @rapidstu01 Жыл бұрын

  Thank you, I hope it is of some help 👍

• 
  @aik936 Жыл бұрын

  “Playing with my dad”

• 
  @rapidstu01 Жыл бұрын

  Lol 🤣😂 that's bad

• 
  @xactlee Жыл бұрын

  She even cut his wrist in the first try

• 
  @rapidstu01 Жыл бұрын

  Rather a cut on the back of the wrist away from the artery than a blade in the neck!! Tho this is just a reaction drill, it's not real life. That gets nasty and I couldn't do that even gently with my daughter.

• 
  @xactlee Жыл бұрын

  @@rapidstu01 true that, and a good drill. Saw you videos of trapping drills / kali sticks. I like your style. We're you influenced by Jeet kune do / wing Chun?

• 
  @xactlee Жыл бұрын

  Knives are just so dangerous in close quarters, so many things can go wrong, even for the fastest / best, against the novice / broken rythm. But training or it minimizes it substantially

• 
  @rapidstu01 Жыл бұрын

  @@xactlee thanks for the reply, yes 45 years of Thai boxing, jkd , FMA, wing Chung, and a little krav maga. I do believe in cross training. Take what works for you, but by your name I guess you have a similar view??

• 
  @xactlee Жыл бұрын

  @@rapidstu01 most definitely, I mostly emphasize on distance, straight line when it's curved, curved when it's straight. No wasted movement, is the goal. Not fancy, but effective. Trapping is a form of jiu jitsu with strikes, - but nr1, it has to work in real life scenarios. Because usually it is just two or three strikes in the streets, or sucker's get sucker punched,no honor just pure form of human behavior,.. Therefor I salute you my friend for preparing your girl for real life, she'll understand the meaning of it someday, but hopefully not if you know what I mean.

• 
  @CrniWuk Жыл бұрын

  Who ever attacks someone like that with a knife?

• 
  @rapidstu01 Жыл бұрын

  It's just one of many training drills, just blocking and clearing, after doing this with a practice knife or stick it makes empty hands easier.

• 
  @CrniWuk Жыл бұрын

  @@rapidstu01 As long it's just for fun and not actually for self defence against knifes, it's all ok I guess.

• 
  @koen4261 Жыл бұрын

  @@CrniWuk why its bad to train that?

• 
  @koen4261 Жыл бұрын

  Idk u would extend straight

• 
  @frankieg8117 Жыл бұрын

  There would be far less rape if everyone thought their daughter these skills.

• 
  @midnightmoves7976 Жыл бұрын

  Hi Stuart, did you use the Total Seal rings, I have measured mine but my feeler gauges only go to 0.35mm. the gap is bigger. probably about 0.40, where yours pre set also?? thanks for putting the vid up. i have the same pistons.

• 
  @rapidstu01 Жыл бұрын

  Hi, yes I have total seal rings. They came with the cosworth pistons, my gaps from memory were nearly 0.5!! I questioned this with the company that did the rebore's etc, they said it is normal on forged pistons as they expand more than the original items. They build race engines and have a good reputation so iv just carried on. I did position the rings with the gaps as per the instructions tho. Just doing the vale clearances now. I hope you're build goes smoothly. Regards Stuart

• 
  @samuelmaslonka8884 Жыл бұрын

  🤩 քʀօʍօֆʍ

• 
  @midnightmoves79762 жыл бұрын

  Nice.. I have the pleasure of doing this myself today. ill do mine by hand. am using the old valves though :). great vid, very exited to see the motor running. as i bet you are ha ha.

• 
  @rapidstu012 жыл бұрын

  Thanks 👍, I hope yours goes well

• 
  @normanparks76792 жыл бұрын

  You need way more followers bro I don't understand why this information ifnt valuable to others

• 
  @rapidstu012 жыл бұрын

  Many thanks for your comment, I'm new to this a learning as I go!! If these videos help anyone that's good, many of us can't afford a specialist at £100+ per hour.

• 
  @normanparks76792 жыл бұрын

  @@rapidstu01 I agree, I want to also learn before I do it (a year in advance) so when I am ready and have everything I do it right instead of making a mistake that costed me hundred if not thousands

• 
  @hskajdhf59072 жыл бұрын

  🤣cute

• 
  @pamelaraffel91423 жыл бұрын

  This is raw, live and keepin it real. Cheers Stuart. Well done.

• 
  @mindofthewarrior14873 жыл бұрын

  This is horseshit

• 
  @rapidstu0110 жыл бұрын

• 
  @rapidstu0110 жыл бұрын

• 
  @oldmanofbarfighting10 жыл бұрын

  excellent knife disarm flow series. thank you sir!

• 
  @rapidstu0112 жыл бұрын

  Hi, the next one is in september but the day isn't decided yet, mike dunnage organises the event and you can get hold of him on youtube- call2arms regards stu

• 
  @fightsans12 жыл бұрын

  Hi this is great do you know when the next call2arms is taking place?

• 
  @rapidarnis14 жыл бұрын

  nice

• 
  @paulb84314 жыл бұрын

  Who's that young bloke? Nice one mate.