One would think by now somebody after ten years of this video would make a heel toe shifter to slide under the frame off the shaft and back up between the pegs and the kick stand. 2023 KLH 650 anyway.
@tonysoprano45878 ай бұрын
How do you remove the plastic cover over the spark plug?
@MrEdb1969Күн бұрын
It just pops off. The side cover has screws that come off easy.
@benmatthews72739 ай бұрын
Great video 🎉
@MJ-5k Жыл бұрын
FYI I would sand down those rusty spots and seal them with either some rust paint or touchup pen Eose the water will ALWAYS make its way in
@kimhorton6109 Жыл бұрын
Damn nice looking bags. The finish is killer. I wouldn’t know how to wire them
@vqfive Жыл бұрын
What is the overall width of the bags on the bike?
@MrEdb1969 Жыл бұрын
I don't have them anymore. I don't know. Sorry.
@kimhorton6109 Жыл бұрын
What company did you buy these from? They look a little light but look good on the bike.
@MrEdb1969 Жыл бұрын
I'm sorry, that was years ago. I cannot remember.
@calebgreen9753 Жыл бұрын
I have a 2007 mercury 90hp elpto that I’ve recently bought that was in salt water I tried a new starter, solenoid, and regulator rectifier, and a brand new battery bought 2 months ago and the starter spins the flywheel but won’t spin it fast enough to crank. If I take the pull rope and wrap it around the flywheel and pull it will crank after a few try’s. Did yours have any problems similar to that. If anyone has any ideas or know anything to fix that will be appreciated.
@MrEdb1969 Жыл бұрын
Geez, this is strange to me. My first thoughts are, is the battery the right one and have enough amp output? Are the positive/negative cables new, the right gauge/size and not corroded as well as having a solid connection?
@MrEdb1969 Жыл бұрын
kzread.info/dash/bejne/pWx3sNahp8LLlrQ.html
@calebgreen9753 Жыл бұрын
I haven’t checked the cables I’m going to do that after work today and the battery is way more that what I need to crank the 90
@calebgreen9753 Жыл бұрын
It wasn’t the battery cables do you have any other ideas
@calebgreen9753 Жыл бұрын
My starter spins and turns the flywheel just not fast enough to start it
@mrspin3315 Жыл бұрын
Don't tip over the generator to empty the fuel tank, not when it is full of oil! Break in oil should not be synthetic! Or it won't break in.
@MrEdb1969 Жыл бұрын
Considering I mentioned that if you were to do this, to turn the generator over just for a few moments, In order to get the one gallon of gasoline out of the tank, could you elaborate in detail, internally within the engine, what damage could be done?
@harryguy452 жыл бұрын
What page of instruction manual says 1hr break-in time?
@MrEdb19692 жыл бұрын
Just like any brand new machine, there's always a break in time. You will have the wear and tear of the piston rings on the cylinder walls. Microscopic shavings of metal are going to flow freely through the oil. Not to mention the bearings on the crank shaft and piston rod as well as the valves. All of it is metal on metal when the engine is running for the first time especially when you put a "load" on it. That means more "torque" will happen internally to the engine, thus probably shaving off more very small metal shavings. You want to change that oil 🛢 after the initial break in period of the brand new engine running for the first time. Flush out any metal shavings and start with new oil 🛢. This will help for the longevity of your generator.
@NotSoFast712 жыл бұрын
The fuel capacity according to the manual is 1.06 gallons, not 1.6 as stated in the video. I just got mine today and it's great. Very quiet compared to most larger generators and just a whisper in eco mode. I ordered the magnetic dipstick and an hour meter.
@acres902 жыл бұрын
$481 at home Depot....worth it?
@NotSoFast712 жыл бұрын
$429 on Amazon, and yes, it's well worth it.
@Dark-nq6bn2 жыл бұрын
What year is the car?
@MrEdb19692 жыл бұрын
2007
@masterful75742 жыл бұрын
WEN not WIN.
@bc40922 жыл бұрын
THANK YOU!!!
@ricbryandado21722 жыл бұрын
How much oil did you put?
@MrEdb19692 жыл бұрын
17.1 fl oz.
@ronaldeddins53602 жыл бұрын
Sounds like what I’m experiencing. Thanks
@verystupidhandle3 жыл бұрын
Why is your Video soo small in size? Squished? Odd
@MrEdb19693 жыл бұрын
I am not sure how that happened. I was using my LG cell phone at the time.
@grungestoryteller3 жыл бұрын
Thank you I have a question how come your video is like really long like up-and-down ways how did you get it to do that but anyways sorry I just wanted to thank you I've been trying to baby this generator I have the same exact one I bought it a couple years ago for my cotton candy business and my church boyfriend never really was helpful with it while with anything and I just finally left him he's like a textbook narcissistic gaslighting chode and he basically purposely didn't tell me a bunch of stuff so I'm kind of camping in my car so I can find an apartment here in Seattle or save money for an RV as what I really want to do but the stuff you told me probably save my generator without going into too much detail the only thing is I didn't understand what you were saying about this dipstick so I bought the metal thingy and yeah that's a good idea to get that timer thing I will listen to the video again and try to find it but on the dipstick how far should it go up it's just a bunch of lines I don't see like a part that says full
@grungestoryteller3 жыл бұрын
I hope there's not a bunch of crazy typos in there I'm using my microphone and just trying to make sure I'm using this right one thing I have to say this kind of weird is I have a really new phone that usually only takes like 20 minutes to charge on a landline and it literally takes 4 hours to charge plugged into the USB ports on this thing does that seem weird to you? Anyhow I don't know if you're even paying attention to this video you posted any more sometimes people post stuff and if it was years ago they're not even active on KZread anymore if I see that you're active on here I would love to actually call you and ask you some questions and I would be happy to compensate you I can send you some organic cotton candy or something some kettle corn- salmon jerky!? 😁
@MrEdb19693 жыл бұрын
Hi, about the video, I just used my LG cell phone to make the video and do not know why it did that format. As for the oil dip stick, you may have a couple of lines or dots on them. The fill mark should be in between them. Another good way to know when your generator is full of oil is when you put the new oil in the generator, make sure it is level and when you see oil come to the bottom of the threads for the oil dip stick, that is full. Not overflowing.
@willmeredith81733 жыл бұрын
Hello just saying your video I'll order the same bags what was your process
@MrEdb19693 жыл бұрын
I'm not sure what you mean by what was my process? I don't have the bike anymore with the bags. But I did like them.
@mgoody87823 жыл бұрын
$500 ? They saw you coming. I payed $399 , but prefer my Honda
@paulsosa18722 жыл бұрын
I have to kick myself I paid $400 for a used one & the jet was clogged I had to take apart the carb to get to the jet to clean it.
@NotSoFast712 жыл бұрын
@@paulsosa1872 Yeah, they are $429 now new on Amazon.
@JimmieJohn3 жыл бұрын
look nice!
@donalddday77413 жыл бұрын
mine stopped running after 6 months had no compression was checking it out and found that the air tube from filter box to carb on back side never put in filter box all the way so it was sucking dirt for six months in Quartzsite Az and just ate up the cylinder never again will i spend that kind of money on bad workmanship
@MrEdb19693 жыл бұрын
Thank you so much for letting me know this. I'm definitely going to be checking my now. I'm so sorry this happened.
@michaelevans72613 жыл бұрын
Great introduction :)
@chrisdark55683 жыл бұрын
Do you get a small puff of smoke when the generator is on eco mode idling.. Then it revs up when there is a load on it an the rpms increase! Just curious if that is normal! The puff of smoke only last a second and goes right away. Just happens when it rpms up under load. Thanks. My oil level is perfect!
@MrEdb19693 жыл бұрын
No I don't get that. If its just a puff of smoke, I wouldn't worry about it to much. It's just burning off a bit of oil coming through the o rings on the piston or leaking through the valve stem seal up on top of the engine. As long as the smoke is not long and consistent and your oil is not burning off to fast, you'll just have to live with it unfortunately but it won't hurt your motor. Just puffs smoke.
@MrEdb19693 жыл бұрын
Or your piston rings breaks are lined up and is allowing a tad of oil seepage into the chamber... Nothing you can really do about that either. It won't hurt as long as it's not too much.
@edwardhowell68753 жыл бұрын
Is this the short or tall folding rack? 21.5inch? Thanks for the video as well.
@MrEdb19693 жыл бұрын
It's the short one. That is why it close to the wall. I wanted the one closer to the wall so I could use my garage too.
@alexherman19873 жыл бұрын
What’s the warranty on it?
@MrEdb19693 жыл бұрын
Hey Alex, I'm not sure it's probably the standard one year warranty. I got it for hurricane season so in about 5 years time I'll probably have about 20 hours on it. Not much at all. For me it will be way past the warranty.
@The_Snowbike_Channel2 жыл бұрын
2 years
@user-zo1xc8mf5s3 жыл бұрын
Please talk to me
@user-zo1xc8mf5s3 жыл бұрын
Nice bike, thank you for this review. Where did you get these bags?
@MrEdb19693 жыл бұрын
I don't remember, it has been so long ago.
@ladykilla63 жыл бұрын
Great video, what kind of shims did you use to get legs even with garage floor?
@MrEdb19693 жыл бұрын
Just some small pieces of wood. That was it.
@ladykilla63 жыл бұрын
MrEdb1969 ty
@SwishRecordsInc3 жыл бұрын
I did the wire swap today and it worked beautifully. Thanks a million man
@SwishRecordsInc3 жыл бұрын
I have the same problem on my 115 .gonna do this
@haydlew3 жыл бұрын
Did it make any difference for your 115?
@DCGULL013 жыл бұрын
Thank you very much. Useful, functional review & usage/operation review- greatly appreciated. You seem to trust it within the limited testing performed, but- changing the oil, spark plug access, float bowl drain (Really happy to learn that!)- now, I'll buy it on sale along with a magnetic oil plug, an hour meter and create a run/stop sheet for my wife (which I'll zip tie to the handle) so even she can use it when I'm not around. Best functional review of any generator I've seen to date, by the way. Only the information we need, no silly unboxing....
@MrEdb19693 жыл бұрын
Thank you so much! Yes I have already done all of that and found it so time-consuming. 😆 It was exactly how I wanted to make the review, straight to the point.😉
@mgoody87823 жыл бұрын
Yeah , if doesn’t have a clock attached to it woman couldn’t use it
@rogercisneros61663 жыл бұрын
Thank you very detailed review, again thank you for sharing 👍🏽👌
@vasilisvosios89133 жыл бұрын
hi. i'm from greece.does anyone knows how must be the compession at this motor?thanks
@Cuongphubuo3 жыл бұрын
110 psi
@calichemorales4 жыл бұрын
I have a 1999 2 stroke 150 mercury outboard, it takes me several attempts before it starts. I replaced the fuel filter and fuel/water separator and still hard to start.. once it has been running for while and I turn it off, it'll start right away. Can this ge the battery cables? Thanks a lot.
@MrEdb19694 жыл бұрын
It doesn't sound like it. If there is corrosion towards the ends of your tables, this will reduce the amount of amperage your starter needs to turn the motor. The corrosion interface would be a consistent problem
@petelaflamme83464 жыл бұрын
Nice bags. Who's whistling in the video?
@Meatnewdadbod4 жыл бұрын
What did it sound like when you're trying to start it before? Did it make any noise? Or did it make no noise at all? I have a 2090 horsepower Mercury motor and right now I'm having a problem out of nowhere it just won't start. It has a bunch of new components basically completely rebuilt.
@natedkauffman4 жыл бұрын
Could you attach a rope to fly wheel and start it that way?
@MrEdb19694 жыл бұрын
There is one under my hood and I tried it one time. It's very difficult to pull that motor. But I guess it can be done.
@calebgreen9753 Жыл бұрын
@nathan Kauffman did this solve your issue I am having the same issue right now
@natedkauffman Жыл бұрын
@@calebgreen9753 I cleaned my lines. And played with idle. Seemed to work out alot better then. Also my inline filter had absolute mud inside it. So replaced that also
@calebgreen9753 Жыл бұрын
@ nathan Kauffman I cleaned and checked all wires they were fine I have a new battery and can start using the rope. But when I switch the key on and try that way the starter spins and spins the flywheel and the flywheel won’t spin fast enough to crank and starter get stuck
@natedkauffman Жыл бұрын
@@calebgreen9753 can you tighten your fly wheel at all? Does it sound like it's trying when you spin the wheel? Also can you find ur fuel line and just trace the steps making sure the fuel goes from point a to b with no clogs
@terrysmith74544 жыл бұрын
I HAVE A PROBLEM I HAVE A PONTOON BOAT WITH A 50HP 2 STROKE MERCURY OUTBOARD , WANT SAY ANYTHING ALL MY LIGHTS WORK FINE /MY DEBT FINDERS WORK BUT NO SOUND FROM THE ENGINE ,STARTER WAS CHECKED ITS GOOD , BATTERY NEW WHAT ELSE CAN I CHECK
@jorgeortizhernandez29514 жыл бұрын
Lo único que faltó, el color , la prefiero azul , x lo demás excelente, y completa .
@Hawkcrom4 жыл бұрын
Looks nice ! Question what does the spring do
@MrAtaripitbull5 жыл бұрын
I'm having that problem right now. Starter engages the flywheel but won't turn it. All my connections are clean and when I engage the starter, my on board chargers light turns from green to yellow on one try so I must have a dead cell.
@MrEdb19695 жыл бұрын
Either that or your cables have corrosion throughout them. Coming from the ends that are exposed mainly and not the ends that are inside the hood of the motor, considering it's a dry clean area. Maybe you could take a utility knife and cut the installation around the positive and negative cable, up about 4 to 6 in to see if there is corrosion in between the wires of the cable.
@MrEdb19695 жыл бұрын
kzread.info/dash/bejne/pWx3sNahp8LLlrQ.html
@noes.castillol.49355 жыл бұрын
I have a 2004 115hp mercury 4 stroke, turn on but it does't take off, I do not know what it would be, we already did the services (spark plugs, oil, oil filters and we thought that doing the service was going to be fixed, but it stayed the same. If any body has an idea of what it could be! Thanks
@bluebeema5 жыл бұрын
where is the choke on these engines?
@MrEdb19695 жыл бұрын
It is where the key ignition is. As you cold start, push in at the same time and hold for a second or two until ignition, then release the key.
@oldeskoolfool83605 жыл бұрын
Should be using lag bolts into the stringer, the holes for the wood screws are the initial adjustment.
@kkelley0555 жыл бұрын
Did you have a problem with the spacing between the barbell sleeve and jhooks?
@MrEdb19695 жыл бұрын
Not really. There is about an inch of play on both sides. Yes, when I'm done with the lift, it's sometimes hard to set it down perfectly but, the j hooks are big, so the bar won't slip off the j hook.
@futbol1972 Жыл бұрын
So the barbell does not fit right or it barely fits? Or should I purchased better jhooks?
@Nickraculous5 жыл бұрын
I'm looking into these, are they designed to match up to stud spacing in the wall? I'm curious about the initial installation
@MrEdb19695 жыл бұрын
You will need to put up a Stringer. That is what I have on my wall, a 2 x 6 that is 60 in Long. The Stringer is attached to the studs which happened to be 16 inches Center 2 Center. The folding rack then secures to that wooden Stringer.
@jc513735 жыл бұрын
pictures on their website show an additional lag into the stringer likely into a stud behind it or concrete. I wouldn't trust just the wood screws into the stringer for support.
@yournightmare99995 жыл бұрын
I have same wet spare tire and Jack stant to the half of water 💦 and dry carpet outside in Camry 2009 maybe I have same issue or t-light leak somewhere inside no idea
@MrEdb19695 жыл бұрын
I am finding out that the weather seal was the issue for me, having water in the trunk. We've already had rain since I siliconed the weather seal and it is dry back there.
@yournightmare99995 жыл бұрын
@@MrEdb1969 I also think this is probably seal I Park my car outside and I remember one day in winter cold day I try to open trunk it's hard but I opened wits seal like 1,1/2 foot maybe I should replace whole seal for new
@yournightmare99995 жыл бұрын
And one week ago I have accident I cut two right side tire on road construction and I wanna remove spare tire but jack stand and spare tire was a half frozen in ice ❄ 😂😂 and I can't remove spare tire
@cwwhite46854 жыл бұрын
@@MrEdb1969 what caused you to inspect under the trunk? We've developed a strange smell and the rubber/foam under the spare tire seems to be the culprit.
@grandfury56095 жыл бұрын
I have a 115hp same motor yesterday I was out on the water and it would start up for a few seconds then turn off so I waited 20 minutes started up fine so i took it around the lake everything seemed fine so I turned it off 30 minutes later I tried to start it and it didn't even crank, no sound nothing.. swapped batteries since I carry another one and nothing..jackplate, guages, radio are fine but nothing when I turn the key🤔🤔🤔
@MrEdb19695 жыл бұрын
Your cables could be corroded which would keep those amps getting to the starter. Then, it could be your solenoid also...
@grandfury56095 жыл бұрын
@@MrEdb1969 yea i was thinking it'd either be a starter problem or solenoid but i wonder why it was starting up and cutting off after 10 seconds and then starting up fine then just dead in the water.
Пікірлер
One would think by now somebody after ten years of this video would make a heel toe shifter to slide under the frame off the shaft and back up between the pegs and the kick stand. 2023 KLH 650 anyway.
How do you remove the plastic cover over the spark plug?
It just pops off. The side cover has screws that come off easy.
Great video 🎉
FYI I would sand down those rusty spots and seal them with either some rust paint or touchup pen Eose the water will ALWAYS make its way in
Damn nice looking bags. The finish is killer. I wouldn’t know how to wire them
What is the overall width of the bags on the bike?
I don't have them anymore. I don't know. Sorry.
What company did you buy these from? They look a little light but look good on the bike.
I'm sorry, that was years ago. I cannot remember.
I have a 2007 mercury 90hp elpto that I’ve recently bought that was in salt water I tried a new starter, solenoid, and regulator rectifier, and a brand new battery bought 2 months ago and the starter spins the flywheel but won’t spin it fast enough to crank. If I take the pull rope and wrap it around the flywheel and pull it will crank after a few try’s. Did yours have any problems similar to that. If anyone has any ideas or know anything to fix that will be appreciated.
Geez, this is strange to me. My first thoughts are, is the battery the right one and have enough amp output? Are the positive/negative cables new, the right gauge/size and not corroded as well as having a solid connection?
kzread.info/dash/bejne/pWx3sNahp8LLlrQ.html
I haven’t checked the cables I’m going to do that after work today and the battery is way more that what I need to crank the 90
It wasn’t the battery cables do you have any other ideas
My starter spins and turns the flywheel just not fast enough to start it
Don't tip over the generator to empty the fuel tank, not when it is full of oil! Break in oil should not be synthetic! Or it won't break in.
Considering I mentioned that if you were to do this, to turn the generator over just for a few moments, In order to get the one gallon of gasoline out of the tank, could you elaborate in detail, internally within the engine, what damage could be done?
What page of instruction manual says 1hr break-in time?
Just like any brand new machine, there's always a break in time. You will have the wear and tear of the piston rings on the cylinder walls. Microscopic shavings of metal are going to flow freely through the oil. Not to mention the bearings on the crank shaft and piston rod as well as the valves. All of it is metal on metal when the engine is running for the first time especially when you put a "load" on it. That means more "torque" will happen internally to the engine, thus probably shaving off more very small metal shavings. You want to change that oil 🛢 after the initial break in period of the brand new engine running for the first time. Flush out any metal shavings and start with new oil 🛢. This will help for the longevity of your generator.
The fuel capacity according to the manual is 1.06 gallons, not 1.6 as stated in the video. I just got mine today and it's great. Very quiet compared to most larger generators and just a whisper in eco mode. I ordered the magnetic dipstick and an hour meter.
$481 at home Depot....worth it?
$429 on Amazon, and yes, it's well worth it.
What year is the car?
2007
WEN not WIN.
THANK YOU!!!
How much oil did you put?
17.1 fl oz.
Sounds like what I’m experiencing. Thanks
Why is your Video soo small in size? Squished? Odd
I am not sure how that happened. I was using my LG cell phone at the time.
Thank you I have a question how come your video is like really long like up-and-down ways how did you get it to do that but anyways sorry I just wanted to thank you I've been trying to baby this generator I have the same exact one I bought it a couple years ago for my cotton candy business and my church boyfriend never really was helpful with it while with anything and I just finally left him he's like a textbook narcissistic gaslighting chode and he basically purposely didn't tell me a bunch of stuff so I'm kind of camping in my car so I can find an apartment here in Seattle or save money for an RV as what I really want to do but the stuff you told me probably save my generator without going into too much detail the only thing is I didn't understand what you were saying about this dipstick so I bought the metal thingy and yeah that's a good idea to get that timer thing I will listen to the video again and try to find it but on the dipstick how far should it go up it's just a bunch of lines I don't see like a part that says full
I hope there's not a bunch of crazy typos in there I'm using my microphone and just trying to make sure I'm using this right one thing I have to say this kind of weird is I have a really new phone that usually only takes like 20 minutes to charge on a landline and it literally takes 4 hours to charge plugged into the USB ports on this thing does that seem weird to you? Anyhow I don't know if you're even paying attention to this video you posted any more sometimes people post stuff and if it was years ago they're not even active on KZread anymore if I see that you're active on here I would love to actually call you and ask you some questions and I would be happy to compensate you I can send you some organic cotton candy or something some kettle corn- salmon jerky!? 😁
Hi, about the video, I just used my LG cell phone to make the video and do not know why it did that format. As for the oil dip stick, you may have a couple of lines or dots on them. The fill mark should be in between them. Another good way to know when your generator is full of oil is when you put the new oil in the generator, make sure it is level and when you see oil come to the bottom of the threads for the oil dip stick, that is full. Not overflowing.
Hello just saying your video I'll order the same bags what was your process
I'm not sure what you mean by what was my process? I don't have the bike anymore with the bags. But I did like them.
$500 ? They saw you coming. I payed $399 , but prefer my Honda
I have to kick myself I paid $400 for a used one & the jet was clogged I had to take apart the carb to get to the jet to clean it.
@@paulsosa1872 Yeah, they are $429 now new on Amazon.
look nice!
mine stopped running after 6 months had no compression was checking it out and found that the air tube from filter box to carb on back side never put in filter box all the way so it was sucking dirt for six months in Quartzsite Az and just ate up the cylinder never again will i spend that kind of money on bad workmanship
Thank you so much for letting me know this. I'm definitely going to be checking my now. I'm so sorry this happened.
Great introduction :)
Do you get a small puff of smoke when the generator is on eco mode idling.. Then it revs up when there is a load on it an the rpms increase! Just curious if that is normal! The puff of smoke only last a second and goes right away. Just happens when it rpms up under load. Thanks. My oil level is perfect!
No I don't get that. If its just a puff of smoke, I wouldn't worry about it to much. It's just burning off a bit of oil coming through the o rings on the piston or leaking through the valve stem seal up on top of the engine. As long as the smoke is not long and consistent and your oil is not burning off to fast, you'll just have to live with it unfortunately but it won't hurt your motor. Just puffs smoke.
Or your piston rings breaks are lined up and is allowing a tad of oil seepage into the chamber... Nothing you can really do about that either. It won't hurt as long as it's not too much.
Is this the short or tall folding rack? 21.5inch? Thanks for the video as well.
It's the short one. That is why it close to the wall. I wanted the one closer to the wall so I could use my garage too.
What’s the warranty on it?
Hey Alex, I'm not sure it's probably the standard one year warranty. I got it for hurricane season so in about 5 years time I'll probably have about 20 hours on it. Not much at all. For me it will be way past the warranty.
2 years
Please talk to me
Nice bike, thank you for this review. Where did you get these bags?
I don't remember, it has been so long ago.
Great video, what kind of shims did you use to get legs even with garage floor?
Just some small pieces of wood. That was it.
MrEdb1969 ty
I did the wire swap today and it worked beautifully. Thanks a million man
I have the same problem on my 115 .gonna do this
Did it make any difference for your 115?
Thank you very much. Useful, functional review & usage/operation review- greatly appreciated. You seem to trust it within the limited testing performed, but- changing the oil, spark plug access, float bowl drain (Really happy to learn that!)- now, I'll buy it on sale along with a magnetic oil plug, an hour meter and create a run/stop sheet for my wife (which I'll zip tie to the handle) so even she can use it when I'm not around. Best functional review of any generator I've seen to date, by the way. Only the information we need, no silly unboxing....
Thank you so much! Yes I have already done all of that and found it so time-consuming. 😆 It was exactly how I wanted to make the review, straight to the point.😉
Yeah , if doesn’t have a clock attached to it woman couldn’t use it
Thank you very detailed review, again thank you for sharing 👍🏽👌
hi. i'm from greece.does anyone knows how must be the compession at this motor?thanks
110 psi
I have a 1999 2 stroke 150 mercury outboard, it takes me several attempts before it starts. I replaced the fuel filter and fuel/water separator and still hard to start.. once it has been running for while and I turn it off, it'll start right away. Can this ge the battery cables? Thanks a lot.
It doesn't sound like it. If there is corrosion towards the ends of your tables, this will reduce the amount of amperage your starter needs to turn the motor. The corrosion interface would be a consistent problem
Nice bags. Who's whistling in the video?
What did it sound like when you're trying to start it before? Did it make any noise? Or did it make no noise at all? I have a 2090 horsepower Mercury motor and right now I'm having a problem out of nowhere it just won't start. It has a bunch of new components basically completely rebuilt.
Could you attach a rope to fly wheel and start it that way?
There is one under my hood and I tried it one time. It's very difficult to pull that motor. But I guess it can be done.
@nathan Kauffman did this solve your issue I am having the same issue right now
@@calebgreen9753 I cleaned my lines. And played with idle. Seemed to work out alot better then. Also my inline filter had absolute mud inside it. So replaced that also
@ nathan Kauffman I cleaned and checked all wires they were fine I have a new battery and can start using the rope. But when I switch the key on and try that way the starter spins and spins the flywheel and the flywheel won’t spin fast enough to crank and starter get stuck
@@calebgreen9753 can you tighten your fly wheel at all? Does it sound like it's trying when you spin the wheel? Also can you find ur fuel line and just trace the steps making sure the fuel goes from point a to b with no clogs
I HAVE A PROBLEM I HAVE A PONTOON BOAT WITH A 50HP 2 STROKE MERCURY OUTBOARD , WANT SAY ANYTHING ALL MY LIGHTS WORK FINE /MY DEBT FINDERS WORK BUT NO SOUND FROM THE ENGINE ,STARTER WAS CHECKED ITS GOOD , BATTERY NEW WHAT ELSE CAN I CHECK
Lo único que faltó, el color , la prefiero azul , x lo demás excelente, y completa .
Looks nice ! Question what does the spring do
I'm having that problem right now. Starter engages the flywheel but won't turn it. All my connections are clean and when I engage the starter, my on board chargers light turns from green to yellow on one try so I must have a dead cell.
Either that or your cables have corrosion throughout them. Coming from the ends that are exposed mainly and not the ends that are inside the hood of the motor, considering it's a dry clean area. Maybe you could take a utility knife and cut the installation around the positive and negative cable, up about 4 to 6 in to see if there is corrosion in between the wires of the cable.
kzread.info/dash/bejne/pWx3sNahp8LLlrQ.html
I have a 2004 115hp mercury 4 stroke, turn on but it does't take off, I do not know what it would be, we already did the services (spark plugs, oil, oil filters and we thought that doing the service was going to be fixed, but it stayed the same. If any body has an idea of what it could be! Thanks
where is the choke on these engines?
It is where the key ignition is. As you cold start, push in at the same time and hold for a second or two until ignition, then release the key.
Should be using lag bolts into the stringer, the holes for the wood screws are the initial adjustment.
Did you have a problem with the spacing between the barbell sleeve and jhooks?
Not really. There is about an inch of play on both sides. Yes, when I'm done with the lift, it's sometimes hard to set it down perfectly but, the j hooks are big, so the bar won't slip off the j hook.
So the barbell does not fit right or it barely fits? Or should I purchased better jhooks?
I'm looking into these, are they designed to match up to stud spacing in the wall? I'm curious about the initial installation
You will need to put up a Stringer. That is what I have on my wall, a 2 x 6 that is 60 in Long. The Stringer is attached to the studs which happened to be 16 inches Center 2 Center. The folding rack then secures to that wooden Stringer.
pictures on their website show an additional lag into the stringer likely into a stud behind it or concrete. I wouldn't trust just the wood screws into the stringer for support.
I have same wet spare tire and Jack stant to the half of water 💦 and dry carpet outside in Camry 2009 maybe I have same issue or t-light leak somewhere inside no idea
I am finding out that the weather seal was the issue for me, having water in the trunk. We've already had rain since I siliconed the weather seal and it is dry back there.
@@MrEdb1969 I also think this is probably seal I Park my car outside and I remember one day in winter cold day I try to open trunk it's hard but I opened wits seal like 1,1/2 foot maybe I should replace whole seal for new
And one week ago I have accident I cut two right side tire on road construction and I wanna remove spare tire but jack stand and spare tire was a half frozen in ice ❄ 😂😂 and I can't remove spare tire
@@MrEdb1969 what caused you to inspect under the trunk? We've developed a strange smell and the rubber/foam under the spare tire seems to be the culprit.
I have a 115hp same motor yesterday I was out on the water and it would start up for a few seconds then turn off so I waited 20 minutes started up fine so i took it around the lake everything seemed fine so I turned it off 30 minutes later I tried to start it and it didn't even crank, no sound nothing.. swapped batteries since I carry another one and nothing..jackplate, guages, radio are fine but nothing when I turn the key🤔🤔🤔
Your cables could be corroded which would keep those amps getting to the starter. Then, it could be your solenoid also...
@@MrEdb1969 yea i was thinking it'd either be a starter problem or solenoid but i wonder why it was starting up and cutting off after 10 seconds and then starting up fine then just dead in the water.
@@MrEdb1969 it was the solenoid. 👍