Пікірлер

• 
  @Konstantin419Күн бұрын

  Hello ! I need to replace the laser head with Harman Cardon HD-950. I can't take my head off ! The pull-out tray is in the way.

• 
  @josehugobarrerasanchez8350Күн бұрын

  Buena reparación, estos reproductores son muy buenos vale la pena repararlos tienen el audio clarito sin distorsion y potente, sí escuchamos una memoria USB se escucha HORRIBLE son una PORQUERIA las memorias.

• 
  @bosse43 күн бұрын

  I have the same machine that refused to start after a power outage. I was about to leave it for recycling when I saw this video. I just hit the reset button and it works again. Thank you!

• 
  @jasonpomare56394 күн бұрын

  Good work my friend 👍

• 
  @robertedmead36846 күн бұрын

  Hi The no sound problem you have is a problem in the power supply pcb.

• 
  @robertedmead36847 күн бұрын

  Hi the problem you have with this machine is normally caused by a problem in the power supply. Hope this helps

• 
  @julianround489310 күн бұрын

  Another nice new CDM4 transport wasted It's almost never the laser fyi

• 
  @davidmoss710910 күн бұрын

  Fantastic video

• 
  @dorian-gray14 күн бұрын

  Schwachsinnsvideo!

• 
  @jonathanyork897721 күн бұрын

  My original machine deck B exactly same problem, i can't fix it. Lazer ok, but not playing

• 
  @jonathanyork897721 күн бұрын

  VU meters for recording levels on deck B

• 
  @jonathanyork897721 күн бұрын

  I've got 2 of these machines, identical to yours. Got stuck drawers on deck A. Otherwise play perfectly after 20 years.

• 
  @robertjianu743421 күн бұрын

  Tradu text folosind camera foto greetings from Romania. i have watched your videos hundreds of times....my yamaha 810 won't turn on. I changed the 22uf capacitor but nothing. I don't have a k3850 and I can't find a close equivalent. I made contact between the relay pins on the 230 volt side and the surprise starts after I press the start button. I removed the relay, measured it and the coil is broken. I listened to music like this for hours at a moderate volume and it still works. My question for you is: after measuring the relay power point why do I have 10.4 volts only for 2 seconds when I press the start button then 0 volts? I specify that it still works very well, only that it must be removed from the power socket. I am waiting for an answer. Greetings

• 
  @weakbit63321 күн бұрын

  you can order it here www.ebay.at/itm/400672863535

• 
  @aletay904024 күн бұрын

  The problem with this compact unit is very strange. It sounds to me like the audio and reading capacitors are failing. It is a very typical problem for Technics and Pioneer. I am a technician and I know what I am talking about, especially if you have already changed the optic, the optic is not the audio capacitor. and reading in Technics and Pioneer, the capacitors that usually cause problems are the 1uf 50v 22uf 6.3v and 47uf 6.3v in 99 percent of the Technics and Pioneer that they brought me from other technicians who directly blame the optician with the recap of those 3 Capacitors came back to life and to this day they work without any problems. I would recap that compacter and you know how it comes back to life. That's probably the problem.

• 
  @galwaypat574424 күн бұрын

  Hi I just got an old Sony cdp 797 cd player but my problem is the volume is very low through the 2 sony speakers .I don't have the remote control .Any help would be appreciated .thanks

• 
  @AlexandrSvetlakov25 күн бұрын

  Hello! Denon DCM-500AE does not turn on after three years of rest. The display does not light up. What are the most likely causes?

• 
  @MohammedFaiz-r4i26 күн бұрын

  how to pair remote

• 
  @uzvarbАй бұрын

  Tip for silver. This symptom is when procesor have problems with communication with BD board under mechanism.

• 
  @uzvarbАй бұрын

  Original battery is rechargeable! And it's charge when unit is in AC.

• 
  @marcosvilca7360Ай бұрын

  Espero me pueda ayudar un saludo desde Arequipa Perú gracias

• 
  @MrNeilypopsАй бұрын

  Is the GigaBlue Trio software stable? Is it easy to update the software?

• 
  @razzman2987Ай бұрын

  I wish i have the skills nice man

• 
  @alimobaseri652Ай бұрын

  Hello, when I bought this device, it had exactly the same problem. After watching your training clip, I first replaced the belt and the 1000 microfarad 35V capacitor. The problem was solved by about 95%, and it only gave errors sometimes, but after replacing the 6800 microfarad capacitor, I replaced it, the device no longer works and only gives error messages, what is the reason?

• 
  @DigitalJunior2003Ай бұрын

  My first CD player ❤

• 
  @mireillepinzuti183Ай бұрын

  Hello Mr Weakbit, so sad that WE have not New vidéos from you... Hope you are well. Give us some news please

• 
  @John-so4fqАй бұрын

  Have you (mr weakbit) got a beef with everything british we wouldn't want to start another war now would we now.

• 
  @weakbit633Ай бұрын

  Is Philips a British company? in this Mission is all from Philips built in. so what?

• 
  @Nesha_insАй бұрын

  One of the reasons laser pickup is skipping tracks at the end of CD is that the ribbon (especially OEM ribbon) comes in close proximity/contact with the transformer. The EM field from the transformer interrupts the work of the laser via the ribbon, so the laser skips/stops. You can verify this by placing some protective plastic between the transformer and the ribbon: it skips less.

• 
  @KaJluHuHrpagАй бұрын

  great install))

• 
  @williamwong5627Ай бұрын

  I found this Cambridge CD player in the trash bin. I would like check inside as the CD drawer won't open. Could you please let know the type of screw driver for the screws on the top cover. Thank you.

• 
  @weakbit633Ай бұрын

  I think I remember it was a Torx T6.

• 
  @alynicholls3230Ай бұрын

  I. Can't decide if you a playing for laughs, or you really are just pratting.

• 
  @alynicholls3230Ай бұрын

  Why not just fit the entire working drive into. The working unit?

• 
  @wowermanАй бұрын

  I have fault with Crx550 ot powering up.I left it on with pasused.music from USB.Protection is active as relqy cklick and nothing on diaplay is shown.

• 
  @delarocquejean-jacques5792Ай бұрын

  Cec has made belt transport for different brands. I have an Yba cd delta 3 with a Cec mechanical. It's high end Hifi. Weight is to avoid vibrations. Not the kind of construction you'll find on 500€ cd player. Thanks for your video.

• 
  @janzacek9996Ай бұрын

  perfect video, I subscribe. I have the same yamaha and the same error. dead. apparently it will be the same transformer... some weakness of these yamaha... how did you solve it? do you need to get a new transformer? or how is it going in the video, it works even without a transformer. thank you

• 
  @darkshutter7245Ай бұрын

  Hi! Your repair is great and clean work. I also have a TEAC A-H500 with an issue, so would you help let me know your idea? The left channel on my A-H500 is always outputing at maximal level, however the right channel is good. This affects all input signals, and I have to eliminate the left channel with the balance knob. Some pro guy told me that this might be something wrong with the volume motor. Is is such and could it be replaced with similar spare part? Thanks.

• 
  @HiFiMaan2 ай бұрын

  I sink I can sank you too 😉

• 
  @boomboxforever95672 ай бұрын

  Hi, I have not the Din cord... Can I use alone the CD player ? Thanks a lot

• 
  @weakbit6332 ай бұрын

  no

• 
  @boomboxforever95672 ай бұрын

  Thanks a lot. This is classic din cord or specific yamaha ?

• 
  @alistairmackinnon42162 ай бұрын

  Interesting, but you are kinda scary with the innards. 😯 😄

• 
  @jordanch682 ай бұрын

  Check the motor that positions the laser head to ensure it moves freely. If it's seized it cannot put the laser head unit in first position so the drive motor won't turn on and spin. Usually you'd need to remove the laser head position motor (long silver one on the head gear) apply a few drops of oil and provide it some power for several minutes to free it and see that it moves freely over time.

• 
  @samankumara74612 ай бұрын

  Great job sir 👍

• 
  @constantintanasescu95492 ай бұрын

  👍👍👍

• 
  @davidash10082 ай бұрын

  Thanks for filming this, a local repairer told me I needed to try and source an entire DVD loading deck, now obsolete, but your video enabled me to pull everything apart, clean it all and put it back together. All working fine now! 👍👍

• 
  @winny68922 ай бұрын

  Warum nicht in Deutsch?

• 
  @ChikodiliNnagbo2 ай бұрын

  Pls my Sony hcd md-373 volume break and cant work again, pls can it be constructed or even send me diagram on how to bypass it

• 
  @norbertauer73672 ай бұрын

  Wie kann jemand so viel Blödsinn reden und dauernd lachen (über seine eigene Blödheit). Entlöten/löten kann der Typ auch nicht.

• 
  @ctrlzyx22 ай бұрын

  I have an av570 that needs the integrated output amp chip. I think a lot of these replacement stks may be counterfeit. My sony will sit as i have multiple better spare receivers to use instead. Hope to find a cheap sony at goodwill someday to donate the stk. These sonys have very poor resale value

• 
  @drazenjurkovic31462 ай бұрын

  I have a 340C. I changed the belt, cleaned, and adjusted the drawer to open and close smoothly. After that, the opening and closing worked fine, but when I press Play, it does not play. I noticed that the laser head constantly vibrates, and the transistors on the Precision servo board become hot, emitting a noticeable smell. Can anybody give me some advice on how to fix it? I cannot find a serviceman who is willing and able to fix it. I might attempt to do something on my own with a little help from someone else.

• 
  @SamiJumppanen2 ай бұрын

  Just fixing a CRX-332. It does not click. T2 (secondary transformer) is giving voltages (standby, 3.3 and 6 but it's sometimes varying from 8 to 12 or so) and the microprocessor is doing something. When I plug in AC and measure EEPROM chip data or clock with multimeter in TTL position, I can hear a short burst. Also when doing system reset via the programming port at the back. Standby switch has voltage, it is going to the MCU when pressing. MCU does not seem to output the RY1 control (relay for main transformer). The situation is that I don't see the problem. EDIT: relay coil has failed. I missed the relay control signal because the logic only tries to turn power on for three times. Then need to cut the AC and try again. Facepalm. But these are not difficult to disassemble and put together. Removing the relay now.

• 
  @spiderchord2 ай бұрын

  @weabkit I found a solution. I have exactly this model with exactly this problem. I was about to buy new laser but then found your video. The only thing you need to do is clear all plastic gears and relubricate them with silicon grease and glue the main problem is this metal shift. Remember how hard it was to get it out! Laser should move on this shift freely and smooth as butter. So lubricate it as hell with like lubricant for metal parts like razor blades. If it not going freely it will stuck when laser trying to move. Which lead to skip. Also clean old laser with IPA aka isopropyl. Mine started working.

• 
  @samd323110 күн бұрын

  Je viens de regarder la vidéo j'ai pensé la même chose que vous un nettoyage et un re graissage des parties mobiles engrenage et guide laser

• 
  @Techelfe2 ай бұрын

  Ich habe drei aufgeblähte Kondensatoren gesehen. Standardfehler bei diesem Modell.