Lost Visions Performance is an Automotive Service Company, We Are based out of Mesa, AZ. We offer Services that rang from Basic Maintenance to Overhauling Your Race Engines. Services We offer are not limited to, Mobile Repair, Pick Up and Delivery, Restorations, Modification, Basic Automotive Repair and Diagnostics, etc..
We hope that These How to or DIY videos helps You With Your Projects, In the case that We can not physically.
Thanks for Checking Out Our Channel.
Пікірлер
Thanks so much! Excellent!
Very good video, and instructions, great job. ❤
This method does not work on a V50 D2 from 2011. Or, basically it does work, however, the way to remove the clutch is different. The holes are not 5mm bolt holes, but just holes. There are 3 holes, and there's a tool which fits these holes to be able to hold the clutch to remove the nut. So you need a different tool and a different method.
I have a 2005 Volvo S60 do you think this fix will work on my AC compressor? I'm having the same issues currently
Will that hood fit on my 07 Yukon Denali????
Hi :) What about check engine after ??
U a bad chick !
Where did you purchase the dash from?
Help help. So what can my problem be on my 04 maxima if I replaced both oxygen sensors bank 1 and 2, the mass air flow sensor and cleaned the throttle body, what can be the reason it still stalls out?
If only the Bank 1 O2 sensor was that easy on the '07 3.5L Altima. The clown who designed that engine and the connector for that sensor should look for another line of work. The space behind the intake manifold can barely fit a fist. So disconnecting with removing the intake manifold is pretty much impossible. It's a totally different type of connector.
What is the torque spec for the subframe/ crossmember and torque spec for all the stuff?
Might vary by year. Probably best to grab a Haynes or Chiltons for $20 off ebay.
Good Clear video. Thank You.
Why isn’t the warning of pulling the axle shaft out and possibly getting a vibration in the factory instructions? All that happened to me on my 2020 rav4 XLE AWD
Did that cause knocking noise or any misfire in a cylinder ?
So you used that sealer and nothing else? No gasket? No gasket maker? Just the sealer?
Where dit you put your spare tire with same size you put on your car?? It will fit on tire compartment??
Is this the same as a 7th gen install?
Can you put a remote switch on the BD to trigger the parallel for all batteries to be available?
*PromoSM*
Very helpful! Thanks!
Man's installing headers yet is still rocking the OG airbox with paper filter. At least pop in a K&N cotton filter to let the engine breathe a little better. As I comment on a 3 year old video lol
The one thing he didn’t even touch was how to get the bridge off wtf
Not gunna show us how it sounds?
Just installed mine!! Any tips to get these flanges to seal? every flange leaks, so I need to loosen and redo, but they look straight!
What a F.ken mess!!😅 I really don’t want to do it..🥴🥴🥴
Good job bro
nothing was covered
it helps to show the cover auctlly coming off and how or what you did to break the seal
I've got an idea what to do when my tires need to be changed
Nice, the PT's engine bay is so crowded I'm researching this for our 05 GT. What gauge wire did you use for the relocation and brand/type of terminals and fuse/breaker on both ends. I also saw you used a spray in the trunk area, and by the end of the video it was all black, was that something spraid only or laid on top? Curious on types, brands, etc for everything! Because ebay kills old links unfortunately. Thanks for sharing!
Hi! I wanna install the same kit in my Rav4, any issue so far with the lifting?? Greetings from Chile, South America.
Nope just get it aligned afterwards and enjoy the added ground clearance!
Amazon, 40.00 for the tool kit
Gotta love amazon
Did this on a 2010 maxima, b1s1 02 sensor unfortunately was frozen, so had to remove the intake manifold, and spray wd40, then torch. After i was able to free it, the threads were damaged so i had to rethread it, for it to work. Its a job that can either be easy if your able to free it or extremely difficult.
Sorry to hear that it fought you so badly. Glad you were able to get it going tho
Is the exhaust stock besides the resonator delete and catless downpipe?
Yes it is.
P r o m o S M
Mr beasting this one.
I have a green wire red wire black and blue wire on my summit box
Was it the same layout?
Me thinking it would be difficult putting headers on because of the amount of work needed, it looks like an easy 5 hour job times my experience making it an 8 to 10 hour work 😭😭😭😭
We can call it "quality time" with our cars...
Thank you for this tutorial. It helped me a lot today when I completed my bank 1 sensor 1 change. I thought it through for about a month during other Maintainance to the same area. The brainstorming time lead to doing the repair from the top and moving the mass air flow manifold to access the 02 sensor with and extended socket, torch wrench and swizzle connection. Bought a new jack from auto zone just to familiarize myself with the best wire route to take to execute the change without cutting the wire or keeping the car jacked up without jack stands. 🫡 @OnlyTheArts_
Thanks for the video! I just did this job this afternoon on my S40. I didn't replace the oil cooler hoses, so I didn't have to drain the coolant and just left the cooler hanging. No problems.
Glad it went smoothly 😌
Is that the turbo or non turbo? I saw some motor mounts just like that on ebay.
This was the turbo. Those mounts were amazing 👏
How long did this take you to install?
I absolutely positively hate the hard CHEAP plastic dash in my 2012 sierra Denali. If I were to replace the dash when it cracked, I would look at covering it with faux leather and French stitching.
Exhaust leak in rear
Hey is this the same process for the 2.5t t5 ?
Yes same setup.
Why do you need to drain the coolant?
Coolant runs to the oil cooler at the back of the oil pan. Drained to remove the pan and replace hoses
Are OEM spark plugs required?
No just a quality brand plug. These ones were replaced with a lower heat range plug because of the tune setup.
Thanks, awesome video. What do you think about an AC that just doesn’t come on at all, but DOES come on (system actually works) when you (manually) engage the clutch? The gap could then be again too big, right? Would this fix work for that?
Yes could be a clearance issue. This one would disengage with any kind of load on the engine. We have fixed a few of these this way so far with similar issues and are still going today.
anyone have an idea how much decibels is this exaust? is it more than 94Db until 3000 rpm?
Its 99/100 Db at 4.5k
Gives me courage to attempt this on my Silverado. I do a lot of towing, and I am thinking of doing a built-in guage pod or monitor screen extension where the middle speaker cut out is too. You have had this in a few years now - I am curious how the new dash has held up and where you got it from? Thanks!
Still going strong thankfully. This was a oem replacement dash from GM.
Best video ever