Thanks for this video, good job, no time wasting intro and straight to the point.
@EdmundTarin3 күн бұрын
Mickey Mouse, that’s the wrong way😂
@bhekidlamini11995 күн бұрын
I think most of these comments comes from people who have never set their foot in the mining field 😂
@pratiksachani70957 күн бұрын
Thanks Man
@doctorstrange847815 күн бұрын
Explain what you're doing verbally. It would make the video better
@beltsplicertech860816 күн бұрын
Good job..is it alegator MR2..
@dualaccumulator19 күн бұрын
The second item you tried removing with the puller is called a locking collar, its supposed to be loosened before its removed.
@lukasz20i4Ай бұрын
to me you are amateurs. the first sleeve must be knocked off. This bearing model is clamped with this bushing. the end of the shaft was beaten with a hammer, you can see it. and this shaft is damaged, lack of alignment, replacing the bearing will help for a while
@jambasicskills1970Ай бұрын
Absolutely your correct if we go on proper fixing this bearing but for the situation depends in the time you need it must, so we go how just to run that conveyor asap. Thank you for your precious comment.
@AverageCitizen3332 ай бұрын
honestly, this is kinda subjective and all, but i spotted several things that should be done differently.
@jambasicskills1970Ай бұрын
Yes you are correct. There are unnecessary need to fix on that bearing but because no available parts to use in that time so we're just fix it temporary permanent lol
@AustinShockSS2 ай бұрын
Thank for the tip. I used a dremel to do the same thing. Sucks you can’t pull the hub since it’s a single sealed unit. Honda should have left a slot or clearance to pull the stud out.
@jambasicskills1970Ай бұрын
You're correct I can pull that hub but need some part to remove. I did this for rush job for this old car lol. Thanks for your comment
@m.kultra41012 ай бұрын
Lock out safety?
@jambasicskills1970Ай бұрын
Yes I was but ms to included in my video clip sorry. Next time I will promise. Thanks Buddy
@bhekidlamini11995 күн бұрын
Another OSHA idiot 😂 how the hell is he going to work on an energized mechine that can start up at any time plus some conveyors have local isolation , you just wanted to point out the overly safe comment that nobody ever needed 😂
@bhekidlamini11995 күн бұрын
By the way you cannot centralize the conveyor when it's not in motion 😂😂😂 your comment wasn't needed old man😂
@jeffdiaz7783 ай бұрын
are you guys ilocanos? lol
@jambasicskills19702 ай бұрын
yep. I'm from Mt. Province from north😍
@chazchampion42813 ай бұрын
So the bearings don’t need washers?
@jambasicskills19702 ай бұрын
Nope but its up to you if need so
@Middleton1193 ай бұрын
What a hacker ! Damn man shim ? Nah grease? Nah cmon this is awful
@jambasicskills19702 ай бұрын
Thanks for your comment made me aware on my jobs. Every jobs varies mostly from the book written to follow, that is basic, but we need to think in a situations where we at. We do sometimes modifying called by nature if we must need so. I'm happy to teach you in related into that job. Appreciated much thanks
@user-mz6xe5ym3w3 ай бұрын
Container loading varieties also for grains😂
@jambasicskills19702 ай бұрын
Thank you Sir
@apr62453 ай бұрын
Excelente!
@jambasicskills19702 ай бұрын
Thank you Sir
@user-mz6xe5ym3w3 ай бұрын
Good job buddy👌
@jambasicskills19702 ай бұрын
Thanks for the visit
@user-qb1ps1ky7r2 ай бұрын
Do you buy the alligator splices in bulk?? I can’t find them in bulk anywhere!
@SimDeck4 ай бұрын
Did anyone use saftey padlocks to lock off the main power and isolate it?
@jaeden_T0pia4 ай бұрын
yeah we call it lock out tag out
@jambasicskills19703 ай бұрын
Yes sir, but I've showed only shutting off circuit breaker and not included LOTO in my video. Thank you for reminding me and hoping next not to forget LOTO include in my video. Thanks appreciated much.
@mikewatt87064 ай бұрын
and don't worry about locking off the power supply
@jambasicskills19703 ай бұрын
I ms to include it in my videos
@mikewatt87064 ай бұрын
heat gun ffs
@jambasicskills19703 ай бұрын
@michaelmcfadden68254 ай бұрын
Lets just cut the shit out of the whole assembly and fix the stud, you sir are a piece of work .....
@user-ip3to9xm6w4 ай бұрын
Looks good, not just basic but also advanced lol 😅
@jambasicskills19703 ай бұрын
Thanks much
@hoplam97174 ай бұрын
That shaft has wore.
@jambasicskills19703 ай бұрын
Yes correct, Just want to run that machine asap for lots of farmers waiting to unload their product
@youdandee15 ай бұрын
I have never used fasteners like that just the flexco fasteners
@jambasicskills19703 ай бұрын
Ye, flexco fastener is better for this kind of conveyor belt. Thanks for your comment
@apr62455 ай бұрын
They probably have no many to remplace that pulley. And the other bearings!!
@jambasicskills19703 ай бұрын
No available parts that time just modified to run it very badly
@MiquelGorbiviUS5 ай бұрын
honda sure makes these difficult. An easy job and they don't provide the space it. I have the same issue, I'm going to have to grind that section
@jambasicskills19703 ай бұрын
That is the easy way and maybe cheapest way lol Thanks Bro
@vishyandypurandat62085 ай бұрын
Nice job only one thing I'll do differently is using a brass hammer.
@jambasicskills19703 ай бұрын
Yes Buds, you can use any hammer as long as you are comfortable using it. Thanks
@gumin72126 ай бұрын
감사합니다 !! 회사에서 베어링이 가끔 고장나서 교체를 해야하는데 하는 방법을 몰라 혼났었는데 덕분에 배웠습니다 !
@jambasicskills19703 ай бұрын
Thank you Sir
@cyh89534773 ай бұрын
^^
@pierrereneerkens76716 ай бұрын
First time working on Bearings?????? kzread.info/dash/bejne/oouctaOrY6zPYaQ.html
@lanceadventure64897 ай бұрын
Informative 😮
@jambasicskills19703 ай бұрын
Thanks appreciated
@danmcgiveron67387 ай бұрын
Dude even my lazy eyed cousin can see the shaft is worn or you have wrong size bearing or collar forcyhe bearing lol Better luck next time I guess
@jambasicskills19707 ай бұрын
Yes you're correct. Shaft was worn out and because we need to run that machine and their was no available roller that time so, nothing else we can do just to made it like that lol
@billcastro20937 ай бұрын
How to remove stuck up shafting of drive roller?
@jambasicskills19707 ай бұрын
use penetrating fluid if doesn't work torch it or else otherwise cut worn-out bearing
@cristiangutierrez21728 ай бұрын
I want to do this for my Honda I only payed $300 for it and I need to get my winter tires on before it’s to late 😂
@jambasicskills19707 ай бұрын
Don't let winter chase you, do it while still behind you
@endolfdaise51688 ай бұрын
Hoping there was LOTOTO after power was shut off
@jambasicskills19707 ай бұрын
LOTO is must before start your job. I ms to include it in my video lol. Thanks for reminding me Bro
@endolfdaise51687 ай бұрын
@@jambasicskills1970 worked maintenance at Michelin and LOTOTO was a Cardinal Rule... fail to do it and get caught... you were marched to gate and terminated on the spot... like wearing arc-flash jacket with open electrical cabinets with 480VAC 3ph power
@Benj708 ай бұрын
Good job Bro 👏
@Benj708 ай бұрын
Informative Buds
@danknoll36138 ай бұрын
He forgot to grease the new bearing.
@danknoll36138 ай бұрын
And also forgot to put his personal lock on the disconnect.
@jambasicskills19707 ай бұрын
Yes Buddy. I ms to show in my video about installing LOTO before starting the project. Thanks for reminding me appreciated.
@3d-rambler7958 ай бұрын
F**d the job
@tengzturiagaiii31858 ай бұрын
Mali po yan pag cutting nyo. Tanyo na sira pa yung part sa gilid at likod. Pwedi lang po yan pokpokin palabas sa likod.
@jambasicskills19707 ай бұрын
Tama po kyo. Pag popokpokin nyo pwede pong masira ung center hub bearing at lalaki and gastos kaso dahil luma na po itong kotset pinakita ko na pwedeng e cut kaso dapat gagamit ng maliit na cutter disk at sinabi ko po na wag gagawin pag bago ang kotse or may nag pagawa lng po sa inyo tiyak magagalit hehe
@tengzturiagaiii31857 ай бұрын
Sabagay may point kayo. Nag hanap po ako ng video pano alisin yang bali na stud. Wala madaming ganyan din po ang ginawa. Kesa mag baklas ka ng buong hub at wheel bearing. Which ang pangit ng desenyo ng honda sa kinalabasan ng ganyan. Kasi may ibang sasakyan po na sa likod gaya ng pinutulan nyo para mailabas ang bali na stud. May inukit o desenyong pwedi itulak palabas dun. Sorry po kung may nasabe akong mali sa unang mensahe ko.
@jambasicskills19707 ай бұрын
@@tengzturiagaiii3185 Opo< kasi kung gusto nyong walang sira or cut ung likod tatanggalin mo ung center hub at possible na masisira sya kaya magiging doble gastos mo. ginagawa ko lng ito sa personal ko at lumang sasakyan, Salamat sa time po kabayan🙂
@dailydad63355 ай бұрын
@@jambasicskills1970 kuya na grinder nyo pala ung likod kasi 2hrs ako nag.ubos para lg matanggal ung luma kaya huminto muna ako sa sunod gawin ko ung ginawa nyo 2003 civic sakin
@Benj708 ай бұрын
Informative Buddy😊
@jambasicskills19707 ай бұрын
Glad you liked it
@robbieblaze888 ай бұрын
The vibration gonna be Willy Nelson high now
@jambasicskills19707 ай бұрын
Maybe your right buddy but as this time it is still properly working lol
@Benj709 ай бұрын
Awesome Buddy😮
@theronwinsby9 ай бұрын
duh.
@A1_filmsss9 ай бұрын
Next time use a soft face hammer to drive your bearings on and that’s an eccentric locking collar on the bearing. You’re suppose to use a punch in the hole that the set screw doesn’t go into and tap it around in the direction of shaft rotation.
@jambasicskills19707 ай бұрын
Your correct buddy. video shows how to do it in basic ways but it's up to maintenance guy how they provide proper tools for every project available.. in that time we did just to run it for it will needed it very badly in the middle of busy operation..
Пікірлер
Thanks for this video, good job, no time wasting intro and straight to the point.
Mickey Mouse, that’s the wrong way😂
I think most of these comments comes from people who have never set their foot in the mining field 😂
Thanks Man
Explain what you're doing verbally. It would make the video better
Good job..is it alegator MR2..
The second item you tried removing with the puller is called a locking collar, its supposed to be loosened before its removed.
to me you are amateurs. the first sleeve must be knocked off. This bearing model is clamped with this bushing. the end of the shaft was beaten with a hammer, you can see it. and this shaft is damaged, lack of alignment, replacing the bearing will help for a while
Absolutely your correct if we go on proper fixing this bearing but for the situation depends in the time you need it must, so we go how just to run that conveyor asap. Thank you for your precious comment.
honestly, this is kinda subjective and all, but i spotted several things that should be done differently.
Yes you are correct. There are unnecessary need to fix on that bearing but because no available parts to use in that time so we're just fix it temporary permanent lol
Thank for the tip. I used a dremel to do the same thing. Sucks you can’t pull the hub since it’s a single sealed unit. Honda should have left a slot or clearance to pull the stud out.
You're correct I can pull that hub but need some part to remove. I did this for rush job for this old car lol. Thanks for your comment
Lock out safety?
Yes I was but ms to included in my video clip sorry. Next time I will promise. Thanks Buddy
Another OSHA idiot 😂 how the hell is he going to work on an energized mechine that can start up at any time plus some conveyors have local isolation , you just wanted to point out the overly safe comment that nobody ever needed 😂
By the way you cannot centralize the conveyor when it's not in motion 😂😂😂 your comment wasn't needed old man😂
are you guys ilocanos? lol
yep. I'm from Mt. Province from north😍
So the bearings don’t need washers?
Nope but its up to you if need so
What a hacker ! Damn man shim ? Nah grease? Nah cmon this is awful
Thanks for your comment made me aware on my jobs. Every jobs varies mostly from the book written to follow, that is basic, but we need to think in a situations where we at. We do sometimes modifying called by nature if we must need so. I'm happy to teach you in related into that job. Appreciated much thanks
Container loading varieties also for grains😂
Thank you Sir
Excelente!
Thank you Sir
Good job buddy👌
Thanks for the visit
Do you buy the alligator splices in bulk?? I can’t find them in bulk anywhere!
Did anyone use saftey padlocks to lock off the main power and isolate it?
yeah we call it lock out tag out
Yes sir, but I've showed only shutting off circuit breaker and not included LOTO in my video. Thank you for reminding me and hoping next not to forget LOTO include in my video. Thanks appreciated much.
and don't worry about locking off the power supply
I ms to include it in my videos
heat gun ffs
Lets just cut the shit out of the whole assembly and fix the stud, you sir are a piece of work .....
Looks good, not just basic but also advanced lol 😅
Thanks much
That shaft has wore.
Yes correct, Just want to run that machine asap for lots of farmers waiting to unload their product
I have never used fasteners like that just the flexco fasteners
Ye, flexco fastener is better for this kind of conveyor belt. Thanks for your comment
They probably have no many to remplace that pulley. And the other bearings!!
No available parts that time just modified to run it very badly
honda sure makes these difficult. An easy job and they don't provide the space it. I have the same issue, I'm going to have to grind that section
That is the easy way and maybe cheapest way lol Thanks Bro
Nice job only one thing I'll do differently is using a brass hammer.
Yes Buds, you can use any hammer as long as you are comfortable using it. Thanks
감사합니다 !! 회사에서 베어링이 가끔 고장나서 교체를 해야하는데 하는 방법을 몰라 혼났었는데 덕분에 배웠습니다 !
Thank you Sir
^^
First time working on Bearings?????? kzread.info/dash/bejne/oouctaOrY6zPYaQ.html
Informative 😮
Thanks appreciated
Dude even my lazy eyed cousin can see the shaft is worn or you have wrong size bearing or collar forcyhe bearing lol Better luck next time I guess
Yes you're correct. Shaft was worn out and because we need to run that machine and their was no available roller that time so, nothing else we can do just to made it like that lol
How to remove stuck up shafting of drive roller?
use penetrating fluid if doesn't work torch it or else otherwise cut worn-out bearing
I want to do this for my Honda I only payed $300 for it and I need to get my winter tires on before it’s to late 😂
Don't let winter chase you, do it while still behind you
Hoping there was LOTOTO after power was shut off
LOTO is must before start your job. I ms to include it in my video lol. Thanks for reminding me Bro
@@jambasicskills1970 worked maintenance at Michelin and LOTOTO was a Cardinal Rule... fail to do it and get caught... you were marched to gate and terminated on the spot... like wearing arc-flash jacket with open electrical cabinets with 480VAC 3ph power
Good job Bro 👏
Informative Buds
He forgot to grease the new bearing.
And also forgot to put his personal lock on the disconnect.
Yes Buddy. I ms to show in my video about installing LOTO before starting the project. Thanks for reminding me appreciated.
F**d the job
Mali po yan pag cutting nyo. Tanyo na sira pa yung part sa gilid at likod. Pwedi lang po yan pokpokin palabas sa likod.
Tama po kyo. Pag popokpokin nyo pwede pong masira ung center hub bearing at lalaki and gastos kaso dahil luma na po itong kotset pinakita ko na pwedeng e cut kaso dapat gagamit ng maliit na cutter disk at sinabi ko po na wag gagawin pag bago ang kotse or may nag pagawa lng po sa inyo tiyak magagalit hehe
Sabagay may point kayo. Nag hanap po ako ng video pano alisin yang bali na stud. Wala madaming ganyan din po ang ginawa. Kesa mag baklas ka ng buong hub at wheel bearing. Which ang pangit ng desenyo ng honda sa kinalabasan ng ganyan. Kasi may ibang sasakyan po na sa likod gaya ng pinutulan nyo para mailabas ang bali na stud. May inukit o desenyong pwedi itulak palabas dun. Sorry po kung may nasabe akong mali sa unang mensahe ko.
@@tengzturiagaiii3185 Opo< kasi kung gusto nyong walang sira or cut ung likod tatanggalin mo ung center hub at possible na masisira sya kaya magiging doble gastos mo. ginagawa ko lng ito sa personal ko at lumang sasakyan, Salamat sa time po kabayan🙂
@@jambasicskills1970 kuya na grinder nyo pala ung likod kasi 2hrs ako nag.ubos para lg matanggal ung luma kaya huminto muna ako sa sunod gawin ko ung ginawa nyo 2003 civic sakin
Informative Buddy😊
Glad you liked it
The vibration gonna be Willy Nelson high now
Maybe your right buddy but as this time it is still properly working lol
Awesome Buddy😮
duh.
Next time use a soft face hammer to drive your bearings on and that’s an eccentric locking collar on the bearing. You’re suppose to use a punch in the hole that the set screw doesn’t go into and tap it around in the direction of shaft rotation.
Your correct buddy. video shows how to do it in basic ways but it's up to maintenance guy how they provide proper tools for every project available.. in that time we did just to run it for it will needed it very badly in the middle of busy operation..
That's good idea Buddy😮
Glad you like it
Okay, that's actually easier to follow 😮
Yap.. If frequently or your routine in field
Good job 👏
Thank you! Cheers!
Informative Buddy😮 Thanks for sharing🎉
So nice of you
Top
Top. Thanks
Thank you too!