Пікірлер

• 
  @anhdaodanh561818 сағат бұрын

  Do you have a video on replacing the suspension rods? My machine keeps going off balance and the spin cycle shakes really hard sometimes

• 
  @tammygould268219 сағат бұрын

  He is the only one that I found on KZread that knows what he was talking about I followed his directions and it worked perfect

• 
  @alizegarciafritz357421 сағат бұрын

  I have the exact same washer, did all the steps right. Only difference while recalibrating is yours are blinking randomly with the lock on. Mines has all the same lights are just on, with the lock on. Yours is making noise and running through mines is quiet and then unlocks. In the coarse of a month I’ve had the motor, lower harness, lid lock, acu board, damper, actuator, parts replaced in increments 4 different techs. The last guy finished the job yesterday and said it was done but all the light are just on when you move the dial. I tried to do a load thinking that’s just how it was gonna be and the lights run through the cycle but the washer doesn’t actually wash. The water fills up, goes quiet for a bit then when it says wash & you hear a spin sound randomly but not like it’s actually washing.. drains and then unlocks but the clothes and soap look how it looked when I put them inside.

• 
  @douglundy5755Күн бұрын

  Just to get the back off! Need to clean the pump!

• 
  @WILLRATH2 күн бұрын

  THANK YOU!!

• 
  @charleskuder39683 күн бұрын

  Whirlpool is junk, I have one of these so called washing machines and your clothes come out just

• 
  @nightwave37823 күн бұрын

  This video is a life saver

• 
  @linseylove96514 күн бұрын

  In the middle of the wash it says DRN I have a load of clothes in there they're just sitting in water and it won't spin it out.

• 
  @andrewgentile24114 күн бұрын

  Thank you. Great demonstration.

• 
  @linseylove96514 күн бұрын

  Thank You, I don't have any instructions on how this works. I just got it yesterday for free. When I put my first load in it won't drain out so I recalibrated it it's washing again I hope I can get it to rinse and drain also. Thank You, I appreciate you.❤

• 
  @escapegrl15 күн бұрын

  I miss the 80’s washers with the push buttons! 😭😭😭 They were tanks.

• 
  @johnshaw28105 күн бұрын

  I have tried every combination on your videos to no avail. On 1st calibration attempt when i get to the rinse light being illuminated it doesn't blink it stays lit up. What d I do now. Thanks!

• 
  @seanhook8916 күн бұрын

  What do I do if it’s stuck in wash mode and won’t drain 😢😢

• 
  @applianceflipper85905 күн бұрын

  kzread.info?search_query=whirlpool+washer+stuck+in+wash+mode

• 
  @seanhook8916 күн бұрын

  I replaced my actuator and put brand new dogs in. But now it’s not doing anything once it fills and goes to wash mode pleeeease help sos

• 
  @slimbaby91375 күн бұрын

  I'm the lead technician at an automotive supplier. I work on all and every type of equipment. Just because the part is new doesn't mean it's good! Especially if it came from amazon or 7:56 They are hit and miss when it comes to electronics. Buy another replacement part then your issue will be resolved. Just FYI even if you had assembled the dogs incorrectly, your washer still would function. Maybe not for long, but it would. Lol. So concentrate on a replacement part

• 
  @bruceparker61426 күн бұрын

  My washer does not have a normal setting. There is nothing at the 12 o'clock setting

• 
  @montgomerycowan68736 күн бұрын

  Thanks

• 
  @jsmall59526 күн бұрын

  What about these stupid all touchscreen HUGE MISTAKE on my part .,,,is there a way to reset mine? It a pos Whirlpool Cabrio top loader . I have never had as much trouble in any washing machine. I had my mothers when I 1st moved out I know that washer lasted 30 years or more. I’m going back to the old school ones

• 
  @Dave_Hrabosky7 күн бұрын

  I am pretty handy and am simply short on time. I looked at new dryers and mine with the bad wheels is probably 10 or 12 years old. Nope. Like my old dryer better than the new ones out there. Your video is great. I am going to do the repair myself. Thanks!

• 
  @7H3P1A6U37 күн бұрын

  This video made the job much less intimidating than I expected it to be, thank you for saving me a couple hundred dollars!

• 
  @andrewsceurman55087 күн бұрын

  This was very helpful in figuring out how to get to the door catch - which had broken.

• 
  @kathyk-d18027 күн бұрын

  Forgot to hook drain back up. Otherwise pretty clear and straightforward

• 
  @gwenniepoo-p1i8 күн бұрын

  so grateful for your help, this worked when i'd almost given up. love your explanation and easy direction. my 12 year old maytag washer is running again!

• 
  @bbruosta8 күн бұрын

  This video saved me! Thanks for sharing.

• 
  @jasonmerrill-yv9xo9 күн бұрын

  Nice job!

• 
  @TheElmatatan289 күн бұрын

  This is gonna sound dumb! But what is the capacitor job? My washer is a Whirlpool but it won't get out of wash cycle. I recalibrated the washer and looked for cloggings but nothing. Its stressful to not know what in the blue hell is going on.

• 
  @Wondereose10 күн бұрын

  I was so confused I couldn't find the latch one video was talking about. You helped a lot thank you!

• 
  @RicardoGonzalezJr12 күн бұрын

  I WOULD LIKE THIS BECAUSE MY FREEZER HANDLE broken last night.

• 
  @HeydaCarreras12 күн бұрын

  My washer works the same after replacing parts, so I don't know what this Calibrates for. I did nothing and it work perfectly

• 
  @aarongrainger254513 күн бұрын

  Thank you for this video, I have always had a hard time putting these belts on before, but with your help, took me about 5 minutes, even with big arms and hands

• 
  @krisfuller280413 күн бұрын

  Absolutely wonderful video. Very helpful. You are wonderful. Thank you.

• 
  @gwenwilson645313 күн бұрын

  Thanks !

• 
  @rolandrogers14 күн бұрын

  3:07 This is the secret NO ONE ELSE has figured out. Spent a long time wrestling with the idler arm wondering if it was supposed to be so tight. This is such a good tip to get the right position for easy belt installation!!

• 
  @carllewis638515 күн бұрын

  Mine stuck at 17?

• 
  @chaos827316 күн бұрын

  Thank you! Very helpful video.

• 
  @TuesdayDavis-v6f16 күн бұрын

  Mines stayed on and tried to spin

• 
  @HeydaCarreras16 күн бұрын

  Calibration? Do I need that after replacing the gearcases? I have some drops leaking at the bottom by rear legs.

• 
  @mykingofharts17 күн бұрын

  Once you've done the diagnostic - then what? Mine was pretty silent during 18/19 when yours was making a sound. Does that mean the agitation/spinning is not working? I don't see what the diagnosis actually is right now.

• 
  @williamhanna522417 күн бұрын

  Excellent

• 
  @chrisbswaby17 күн бұрын

  Excellent video 🎉!!

• 
  @lonnieknight918718 күн бұрын

  No other video said anything about the placement of the pully to help with the excess slack. Was about to lose my mind. Thank you. Now to put it back together 😩😞

• 
  @rc3100318 күн бұрын

  Thank you so much

• 
  @joevara260018 күн бұрын

  You are the Best! Thank you.

• 
  @augustinecouch277819 күн бұрын

  Thanks

• 
  @problemsulfer20 күн бұрын

  will it work with propane?

• 
  @applianceflipper859019 күн бұрын

  Yes it will

• 
  @kristisaxonwithredchutechi568920 күн бұрын

  Thank you

• 
  @tammyleewilder383121 күн бұрын

  Thank you!

• 
  @gabrielkoerner704521 күн бұрын

  Where is his link I need to buy parts and stuff

• 
  @GerardoRH24 күн бұрын

  I am getting a E1 F2 code, what dies it mean and do i press power button to exit

• 
  @masskayaexodus890725 күн бұрын

  U just saved my parent $800. THANK YOU. Watched 20 other videos the require a phd in washer mechanic science ( Lol ) to complete. This was was straight to the point, quick and easy! Ty!

• 
  @DaughterofJudah187426 күн бұрын

  Thank you so much...❤ single mom!!!