Such a waste of material over 50% is waste on hecarry strip, a Eylet maching could produce that way much cheaper and faster production speeds. Truly
@aliyigitale3 ай бұрын
its really atwork ! absolutely
@tigerlin98934 ай бұрын
偷工減料短壽命的模具構造
@user-oh2pi9bj7b5 ай бұрын
asmr求む。
@user-ef4ew4zg2g Жыл бұрын
Красиво но если что-нибудь сломается то конец
@user-yq7sd9uw4f Жыл бұрын
すごい
@Halloguys84 Жыл бұрын
Sugoi 🎉🎉🎉🎉🎉🎉
@KT-ml3ce2 жыл бұрын
ただの順送プレス‼︎
@venkataramanaupadhya52772 жыл бұрын
Please tell and show, what is it finally.
@richardhead82643 жыл бұрын
_It's fascinating to see the extent to which one can draw what was once flat sheet!_ 😲 _And it begs the question, is there any limit to the length that one may obtain?_ 🤔
@alfielao77103 жыл бұрын
It pains me to watch such system. Hydraulic press movement is too high and it can be improved by adding 1 level sensor to lower the movement (upper section of the press). By doing this, the travel time is shortened (means higher productivity) and saves power (shorter movement means lower power requirement to move the press).
@aleksandersuur94753 жыл бұрын
You sure it isn't a type of press with a crankshaft on top providing the power? The travel distance is what it is on these, can't change it like that.
@user-oh2pi9bj7b3 жыл бұрын
この機会いくらくらいですか？
@paulbfields82843 жыл бұрын
Imagine building this die before wire Edm existed(?) !
Пікірлер
Very good. Veri good veri 👍
Such a waste of material over 50% is waste on hecarry strip, a Eylet maching could produce that way much cheaper and faster production speeds. Truly
its really atwork ! absolutely
偷工減料短壽命的模具構造
asmr求む。
Красиво но если что-нибудь сломается то конец
すごい
Sugoi 🎉🎉🎉🎉🎉🎉
ただの順送プレス‼︎
Please tell and show, what is it finally.
_It's fascinating to see the extent to which one can draw what was once flat sheet!_ 😲 _And it begs the question, is there any limit to the length that one may obtain?_ 🤔
It pains me to watch such system. Hydraulic press movement is too high and it can be improved by adding 1 level sensor to lower the movement (upper section of the press). By doing this, the travel time is shortened (means higher productivity) and saves power (shorter movement means lower power requirement to move the press).
You sure it isn't a type of press with a crankshaft on top providing the power? The travel distance is what it is on these, can't change it like that.
この機会いくらくらいですか？
Imagine building this die before wire Edm existed(?) !
Yup did itmany times
この機会1つでいくらくらいするんですか???
いちこめ(((o(*ﾟ▽ﾟ*)o)))
いちこめヽ(ﾟ∀｡)ﾉｳｪｨwww
like a poem
灰皿作ってるのかと思った
我々無知なトーシローが見ると まるで魔法だっ！ 素晴らしいっ！！
1コメw