Пікірлер

• 
  @MilasDragan21 сағат бұрын

  Efekta nema. Izgubljeno vrijeme😂

• 
  @GruzDrajwerКүн бұрын

  Is the LCD from another vehicle? Did you make them yourself?

• 
  @user-xl5np5dp8n17 күн бұрын

  Thanks. Very helpful. Rather tasty music. Usually I hate music.

• 
  @barenekid969528 күн бұрын

  WD40 is NOT lubricant !

• 
  @anthonybrown795928 күн бұрын

  What exactly was the reason for you replacing the master cylinder. In my case the pedal feels like its beginning to stick when you hold the pedal down for any length of time. Think its loosing pressure.

• 
  @diy2world28 күн бұрын

  Pedal low position.

• 
  @maxleng4785Ай бұрын

  is this a mirror swap between 207s? or 207 dimming mirror to 206?

• 
  @diy2worldАй бұрын

  This is for 207 (old/new mirror).

• 
  @Harshavardhan-xh3rjАй бұрын

  Which led light did u use

• 
  @diy2worldАй бұрын

  Watch video part 1!

• 
  @vladimirdjordjevic42142 ай бұрын

  Great video! Can you please tell what do I need to take out from the engine bay in order to come to the master cylinder?

• 
  @diy2world2 ай бұрын

  You need remove battery box.

• 
  @vladimirdjordjevic42142 ай бұрын

  @@diy2world Thank you for answering me so fast!

• 
  @ghostridergr82592 ай бұрын

  What was the symptoms?

• 
  @diy2world23 күн бұрын

  Clutch pedal low position.

• 
  @yarasrinivas38082 ай бұрын

  6 pin how to check

• 
  @JamesLee-dr3nq2 ай бұрын

  I like to know the power and time how to use!, i have try to use the dent not recovery but the paint is burn, so can you share to me how to use the time & power to control the temperature too high and can make the dent gone please?

• 
  @brandonblake17232 ай бұрын

  What kind of cleanser did you use with the water?

• 
  @Harlembfs33 ай бұрын

  thanks bro

• 
  @nan_88833 ай бұрын

  have 3 terminal.you have check 2 terminal..other 1 terminal use for what?tq

• 
  @Tropical1574 ай бұрын

  How long will it last ?

• 
  @h4nw4 ай бұрын

  清洗干净后要浸泡在机油里用细小杆子伸到孔里顶压小圆珠直到没有气泡预先填满油，用手压不动才是好的。液压补偿器如果可以被轻松压缩即失去补偿功能

• 
  @crc16014 ай бұрын

  👍👋👋👋👋👋👋💪💪💪💪

• 
  @emmanuelocran524 ай бұрын

  Can it causes noise on the top of engine head inside?

• 
  @diy2world4 ай бұрын

  Yes.

• 
  @emmanuelocran524 ай бұрын

  @@diy2world ok thanks

• 
  @adhemelfaiky60474 ай бұрын

  My gauges screen in the middle the number part isn’t working properly

• 
  @djeridanemakhlouf33345 ай бұрын

  You need to fill up with oil and confirm good luk

• 
  @Certainblind5 ай бұрын

  Kamay lng nakikita ko😅

• 
  @brak78786 ай бұрын

  Hello, one of the rear sensors is defective. If I replace it with another brand, will it be compatible with the others and work?

• 
  @paulseacroft91456 ай бұрын

  Very clear, step by step instructions. I will have a go changing mine based on these instructions. Cheers guys!

• 
  @hanifiparay89806 ай бұрын

  👍

• 
  @deanjagger11907 ай бұрын

  Seems to be easy enough to do. How about testing the moguals?

• 
  @deanjagger11906 ай бұрын

  My back up sensors work, but the blind spot doesn't work. They both look in good shape. I wonder how to get the conecters of, this was the problem on checking the out. Does anyone know how since the clips are so small?

• 
  @videobreakers-uq4bh7 ай бұрын

  Don't use music for background

• 
  @justaskinquestions4 ай бұрын

  Or mute button? The music is pry the free youtube stuff. I like it better than dead air. Jmo

• 
  @pinpunka7 ай бұрын

  how did you get it off so easily? I tried to move it left and right, pull it down with both hands, but it won't come off.

• 
  @diy2world6 ай бұрын

  You must have strong hand :-)

• 
  @AlexAlex-ru8nx7 ай бұрын

  That posting is SPAMMY, and idiotta music, because can't speak English 😢

• 
  @JasonfromMinnesota8 ай бұрын

  thanks for posting

• 
  @EusGeorge8 ай бұрын

  Hi, they are ultrasonic sensor or electromagnetic?

• 
  @rbarr12009 ай бұрын

  When you buy those lifters from the dealer, they will not compress like that.

• 
  @maksutazil8 ай бұрын

  Yeah same story. Now I'm puzzled shall I or shall not replace them. Was doing my BMW a month ago and they were hard but new exactly the same. Now doing LR and lifter kind a soft

• 
  @rbarr12008 ай бұрын

  If they’re hard to compress by hand , they’re good. If they are easy to compress by hand, they are not good and will break/collapse soon.

• 
  @sagotremi63366 ай бұрын

  Jamais vu de tuto avec autant d’erreurs. En fait c’est plus un tuto sur ce qu’il ne faut surtout pas faire. Le bon poussoir hydraulique est celui qui ne se compresse pas à la main et non le contraire..! Celui qui se compresse rien qu’en le serrant entre les doigts est HS.

• 
  @barenekid969518 күн бұрын

  Lifters Only compress when they have No oil in them. When the lifters are gummed up, the check valve ball is unable to move and the things are rock solid.. Constantly

• 
  @rubenproost25529 ай бұрын

  The metal shavings make me just want to replace it.

• 
  @NoName-DonKai9 ай бұрын

  Thanks 🎉🎉🎉🎉

• 
  @sandeepkamalasanan662010 ай бұрын

  Bent nose plier is good for this job

• 
  @ktpzima89211 ай бұрын

  Most kerültem ide, mert a kerti talicskám fogantyúja leesett! Úgy döntöttem kitolom a szemétgyűjtőbe! Helló

• 
  @muntderpubg2258 Жыл бұрын

  OEM?

• 
  @kennethmetzler-xl7hf Жыл бұрын

  Where and what caused all the metal shavings on the vvt?

• 
  @metaproxy Жыл бұрын

  Thanks!

• 
  @aggelosskapinakis3622 Жыл бұрын

  In order to remove the rear panel you also removed the rear seats?

• 
  @diy2world Жыл бұрын

  Yes, you need remove rear seats.

• 
  @ochoamanuel5710 Жыл бұрын

  Thanks for share....really thaks

• 
  @miosz2368 Жыл бұрын

  Hi I need your help. Could you tell me where on those 3 cables is + , + from rear bulb and ground? Nect question what is the voltage for this mirror? 12 or 5V?

• 
  @diy2world Жыл бұрын

  Wiring has ben inslalled factory, only change mirror, that all. Sorry, all about wiring you must check in Peugeot SEDRE Backup.

• 
  @tuxnoel Жыл бұрын

  Show how u used the spanner

• 
  @makestuffwork9205 Жыл бұрын

  I have two sensors that measure 10k resistance but are still faulty.

• 
  @vilhelm8166 Жыл бұрын

  Could it be the connector, or maybe some wirering issue, bad ground or 12v to it. Because the two sensors should be fine if you get 10k ohm

• 
  @makestuffwork9205 Жыл бұрын

  The wiring is good. If I put a good sensor on the same connector that the bad one was one then it works and clicks. I also have a merc scan tool that shows each sensor's distance information. So unfortunately bad sensors can still show 10k resistance but have a fault elsewhere.

• 
  @makestuffwork9205 Жыл бұрын

  The wiring is good. If I put a good sensor on the same connector that the bad one was one then it works and clicks. I also have a merc scan tool that shows each sensor's distance information. So unfortunately bad sensors can still show 10k resistance but have a fault elsewhere.

• 
  @myshitonyoutube2 ай бұрын

  @@makestuffwork9205 Yes, that's true. I also have 1 bad sensor out of 4 and they all show the same resistance.

• 
  @therealclassic3805 Жыл бұрын

  Is there a name for tage rear seatbelt cover?

• 
  @diy2world8 ай бұрын

  No name.

• 
  @franciscomartinez2551 Жыл бұрын

  Genial

• 
  @kawasakiinitful Жыл бұрын

  thanks for posting this i found one of my sensors had a small amount of physical damage and indeed tested faulty but i guess not all faulty ones have visible damage . liked and subscribed 👌

• 
  @guidofeliz8282 Жыл бұрын

  can it fit a 2005 jetta

• 
  @CesarAugustoRibeiroAroeira Жыл бұрын

  do you have for jetta mk6?

• 
  @diy2world8 ай бұрын

  Sorry no.

• 
  @CrebitKarma Жыл бұрын

  Thank you so much for this video

• 
  @medalalon Жыл бұрын

  Should this work on golf mk4 maybe? 😁