Hello everyone, my name is Claudio and this is my channel El Gallo built. This channel originally started just to document the process of my old build from the ground up. A 2006 Chevy Silverado bagged and bodied on 26s. The truck was nearing the point of reassembly until COVID pandemic made me have to sell it due to economic reasons. Two years of hard work had to be let go.
But now here we are exploring a new route rebuilding a 1968 Chevrolet C10 long bed with a 305 SBC. Lots of work lies ahead, let’s see where we end up! Thank you for your continued support in the channel and for the OGs who were there from the first videos.
Пікірлер
what solder wire did you use?
Good stuff!
Best how to video ever. Courtesy of me😂 and my welding skills
Snitches get stitches!
Was this a long bed converted to short bed or are the beds different
Do you Instagram
How can I contact you señor?
Tienes el link para compare todo el kit
Can you tell us how to lock them in correctly
How much closer do the bars move in vs the leaf springs ? Thinkn of doing this kit but curious if a 12” wheel will fit
Terrible walk thru
Good video thanks!!!
Did you had to eliminate the parking brake
i forgot to buy the pinion shims and i’m installing my flip kit tomorrow can i still install it without them or are they necessary?
Why is it that when I turn my high beams on my low beams turn off?
Im doing a 2007 silverado reg cab short stepside bed took a extended cab frame and shorten it
beautiful work...
Gallo - have you done a 96 converison ?? long bed to short ?? Those frames are wacky
Nice work
Cuanto le corto al chasis
How much did it cost I got a long bed I want to do a short bed conversation
21:10 i laughed too man that difference is ridiculous 😂
That sounds like some fat ass cheeks clapping after a good fart😂
How much for something like this bro
Mamalon viejon yo estoy planeando en hacer una single cab long bed a cortita crewcab
Perfect thank you.
Por nadie tiene explicación como se ase en español
How much does something like this cost
Loving the build Sir couple questions for ya 1. What’s the width of rims and what’s the offset (should say ET on rear of rim that’s your offset #)… 2. what arm kit setup do you have and what are they narrowed ?
Dude used a cherry picker for a cab that’s rad af props if there is a will there is a way!!
How you get the pinion angle?
Hey, love the videos, would like to do this to my truck. I have a few questions like kind of kit and your ball part price installation.
She needs duals
Tire size
Tried to watch it but the music 🤪
how many amp welder?
Step notch was ridiculously huge for a suspension they won't go up any higher. Top links will hit the bed mounts with a 2" bump. Definitely good work overall. Looks nice. At least
U wanna sell the frame table u had made for the crew cab?
is it just one bulb for high and low beam or is it still 2 bulbs
What are those spacers? What do I need to order
Hope you or someone in the comments answer my question do 2006 spindles fit my 08 I already ordered and I’m stressing about them not fitting
What 4 link kit are you using...have a link or part number...great video
Nice video, thanks! I have a 2012 4.3 reg cab long bed and plan on a 2/2 drop. Fair winds and following seas to all.
I think the need to be clocked since the factory bulbs sit in a weird position. You should have read the little manuals.
I have the same problem, I was able to get my high beams to the vertical position but no luck with the low beams, I can't see crap.
Man what ever happened to this truck. Did you ever finish it?
Well one thing to do is the support just needs to be notched bro! 👍🏽
I’ve got the same truck in white I love it so far. Going to install these headlights as well this week. Thank you for the video!
What are all the drops from highest to lowest? I’m getting a drop but idk how low each one is
I like the single potato cannon ❤
Thanks for sharing.