I just got mine today and didnt read fhd instructions until after i had them fully extended and boy are they nice!
@Sly_Wolf_14 ай бұрын
Just an idea to help cut your slot for the blade to through... Cut material almost to size. Stick it to insert with double sided table, replace insert with material attached and raise blade to cut slot. Route edges with guided profile bit, seperate material from factory insert, cut underside notches and now it will fit clearing the blade allowing a full height cut to be raised through it. As for the slit for the RK just use a jigsaw with a straight edge as it doesn't need to be zero clearance.
@solarwinds-4 ай бұрын
Great job and you're super cute!
@AlS.-kn3cq4 ай бұрын
Thank you for the great video, I had lost the instructions manual so your video was very helpful. Once again, thank you
@post1mark7 ай бұрын
Thanks for the video. I just bought a set of these and couldn't/didn't see the instructions tucked inside. As you know, I struggled to figure out how to open for use. Thanks to you, I can finally put these to use.bed to your channel so I can see what other interesting things you've simplified.
@Hansaman587 ай бұрын
Thank you for posting. There is a seller on Etsy making zero clearance inserts for this saw. In Germany so $25 shipping on top of $33 for the insert. Much less expensive to make one.
@Amy_McFarland9 ай бұрын
You should really keep making videos! Finally someone did a vid with the same saw I have! Yeah, now I feel much more confident to make my own zero clearance plate. Thank you!
@abboudworkshop94049 ай бұрын
Thank you! I hope to make more in a couple of months
@55realitycheck11 ай бұрын
man...where are your safety glasses when using the router??? Spectacles, are not the same thing!!!
@LFichna11 ай бұрын
I will follow your steps except all of the safety mistakes.
@alvaroandresbarrazaromero5454 Жыл бұрын
Buenas y saludos desde colombia, a este modelo de sierra se le puede colocar el riel deslizante TS?
@abboudworkshop9404 Жыл бұрын
I do not know what is a TS sliding rail.
@JB-hx3jr Жыл бұрын
Are you still pleased with it after 2 years?
@abboudworkshop9404 Жыл бұрын
Yes. It still works well. I do recommend it.
@Parvindk Жыл бұрын
Thank you for the video, it's great you show the mistakes so we can learn better with you!
@ksplays8652 жыл бұрын
Weaving
@abboudworkshop94042 жыл бұрын
You are on to something
@Sigmaalopha2 жыл бұрын
A table?
@abboudworkshop94042 жыл бұрын
It is flat, but no legs
@jameslund2212 жыл бұрын
Can you put a dado blade on the saw?
@iabboud2 жыл бұрын
Yes, I used a 6" dado stack in it. I think I could do an 8" too.
@jameslund2212 жыл бұрын
@@iabboud how do I remove the riving knife
@iabboud2 жыл бұрын
@@jameslund221 checkout this video to learn how to remove the rising knife. I used an ocilating saw. kzread.info/dash/bejne/Ymilt7qcqMXNf6w.html
@brich2929 Жыл бұрын
@@jameslund221 you have to cut the notch in the knife with a saw. Dremel or oscillating tool
@abboudworkshop9404 Жыл бұрын
Yes i had an 6" dado
@adamik622 жыл бұрын
An instructive film. You could still show what a cut with a factory insert looks like and how with the one with zero clearance made by you in the video. Greetings from Poland Adam
@bobbyshobbies84222 жыл бұрын
Thanks for sharing. And don’t worry about the “mistakes”, I learned from it too! Appreciate it!!!
@abboudworkshop94042 жыл бұрын
Thank you
@shivshah87542 жыл бұрын
Great video . I am new to woodworking . I made this but my keep coming out from the back. Blade is lifting my insert so I am not using it . Can you make one for me ?
@djwill91662 жыл бұрын
great video. Thank you.
@abboudworkshop94042 жыл бұрын
Thank you!
@rubeng.13092 жыл бұрын
Are you happy with the saw? I find lots of reviews of the older model, but nog about this one and i'm seriously in doubt between this one and the dewalt 4792 (similar but a lot more expensive). Best regards
@abboudworkshop94042 жыл бұрын
I have been happy with it. I had it a little over a year now and have used it a lot. Has been a good investment. And for the money, you can't go wrong.
@rubeng.13092 жыл бұрын
@@abboudworkshop9404 thanks for the quick response! If you ever think about making a review with your likes and dislikes, don't hesitate tot inform me 😅 Think you would help out a lot of people in Europe and i would love to share the link ;)
@markyoloup2 жыл бұрын
☕🎁 I bought this coffee maker for myself as a Christmas present and I am very happy with my purchase ! 🎁☕
@solarwinds-4 ай бұрын
I love 'em too.
@chuckberry76922 жыл бұрын
Does the saw still roll over to 45^
@abboudworkshop940411 ай бұрын
No
@nhellman842 жыл бұрын
Nice review!
@abboudworkshop94042 жыл бұрын
Thank you
@YulRun3 жыл бұрын
Learnt a lot thanks, I have the C10RJ not C10RJ(S) only difference I noticed, is mine does not have that lock for the plate, my plate locks in with a little lever on the plate itself.
@ateliemaritom3 жыл бұрын
Uma bela obra de arte parabéns meu amigo🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷
@phuckdatacollection58823 жыл бұрын
Have watched many board vids. This was the first one that made me actually laugh!. And you did cover all the crucial stages. Kudos.
@abboudworkshop94043 жыл бұрын
Thank you:) I mean, what else do you need to know in a Tik tok world :) i do have a longer video on how to glue it :)
@samueladams5843 жыл бұрын
You can use the saw horse as scaffolding with a smaller board 12 x 24
@abboudworkshop94043 жыл бұрын
I am not sure what you mean by 12x24 or how you mean to place it... Can you clarify?
@jasonchuc3 жыл бұрын
When you switched the circular saw blade with the table saw blade, did you have the blade in reverse order?, I noticed the blade brand facing the wrong side and saw dust came out on your side of the table saw.
@abboudworkshop94043 жыл бұрын
You made me look closely... it was in the correct orientation :)
@johnjordan42953 жыл бұрын
Just bought 3 PAIRS of these clearance at a Lowe’s store for $13.06 PER PAIR. Score!!!
@iabboud3 жыл бұрын
That is a fantastic deal
@samhoskins37563 жыл бұрын
I did a thumbs down on the Kobalt sawhorses, not on the gentleman’s video. He did a great job, however these sawhorses seem Clunky and difficult to operate, as he said himself Bora makes a much better product!
@daneyuleb2 жыл бұрын
Dude. Downvote on the Lowes home page. If he did a great job showing you the product that's what you're voting for.
@rusticmusicnj37743 жыл бұрын
Fantastic! Not only do I now know how to make my zero clearance throat plate, but I'm also happy to see someone using the same router table I use!
@abboudworkshop94043 жыл бұрын
Glad it was helpful!
@TheBikersurgeon2 жыл бұрын
I love my Kobalt router table too! tossed my Bosch one in the junk pile.
@MYT1FL2 жыл бұрын
@@TheBikersurgeon you must be joking
@PaganWizard3 жыл бұрын
I have this saw, and really appreciate you posting this video. Can you please do a video detailing how you removed the riving knife??? Thanks in advance!!!
@abboudworkshop94043 жыл бұрын
I actually saw it on another youtube video but I don't have the link handy
@troyfromwork9952 жыл бұрын
The only way I saw was to use a Dremel to cut the bottom of the riving knife.
@azizborashed3 жыл бұрын
Nice video, the music was a tad too loud. Whats the groove for?
@JerryPonds Жыл бұрын
The idea of the groove is that it catches the juices of whatever you are cutting up.
@DominikV2353 жыл бұрын
Awesome stuff. Keep it up man
@abboudworkshop94043 жыл бұрын
Thanks! Will do!
@herbertchung1093 жыл бұрын
You could use your fence to hold insert to make the cut instead of clamps
@abboudworkshop94043 жыл бұрын
That would have been a good idea for me to do :)
@joshuataylor73243 жыл бұрын
How’s it working? Do you notice a difference in dust around the shop?
@abboudworkshop94043 жыл бұрын
It is working well. Filter keeps getting dirty so I know it is taking the dust out of the air! I clean the outer filter every 2-3 weeks using a shop vac. The inner filter is still clean.
@joshuataylor73243 жыл бұрын
@@abboudworkshop9404 Thanks! And I’m enjoying your videos!
@jeffdorrity56093 жыл бұрын
I like your attention to safety (with you camera person’s help)
@abboudworkshop94043 жыл бұрын
Camera people are the best :)
@123goodweb3 жыл бұрын
It is very nice
@socalcraigster3 жыл бұрын
I have the same saw. Thank you for the post.
@denverrenfro29333 жыл бұрын
How are the replacement costs for the filters?
@abboudworkshop94043 жыл бұрын
Filers are about $24 per pair give or take. But you don't have to replace the inside filter as often.
@denverrenfro29333 жыл бұрын
I have been wanting to do this for my Delta saw. Congrats on starting a channel!!
@abboudworkshop94043 жыл бұрын
Thanks Denver! Go for it! It was a fun little project and I got to learn about some intricate details about my saw in the process.
@tanker2423 жыл бұрын
Haha, I saw you doing #1 first and was like, "Oh no! Wait for it.". What did you choose this model over the adjustable version? I heard they might not be as sturdy as this model.
@abboudworkshop94043 жыл бұрын
Yeh, I am sure it won't be the last time I make that mistake! I chose this one because it was on sale and honestly, I don't need more strength than this. My old set were plastic ones from Harbour freight so this is a gigantic improvement!
@tanker2423 жыл бұрын
@@abboudworkshop9404 I got in on the same sale, but if you bought it in person the deal was even better probably because it was clearence. I'm picking my set up tomorrow.
Пікірлер
I just got mine today and didnt read fhd instructions until after i had them fully extended and boy are they nice!
Just an idea to help cut your slot for the blade to through... Cut material almost to size. Stick it to insert with double sided table, replace insert with material attached and raise blade to cut slot. Route edges with guided profile bit, seperate material from factory insert, cut underside notches and now it will fit clearing the blade allowing a full height cut to be raised through it. As for the slit for the RK just use a jigsaw with a straight edge as it doesn't need to be zero clearance.
Great job and you're super cute!
Thank you for the great video, I had lost the instructions manual so your video was very helpful. Once again, thank you
Thanks for the video. I just bought a set of these and couldn't/didn't see the instructions tucked inside. As you know, I struggled to figure out how to open for use. Thanks to you, I can finally put these to use.bed to your channel so I can see what other interesting things you've simplified.
Thank you for posting. There is a seller on Etsy making zero clearance inserts for this saw. In Germany so $25 shipping on top of $33 for the insert. Much less expensive to make one.
You should really keep making videos! Finally someone did a vid with the same saw I have! Yeah, now I feel much more confident to make my own zero clearance plate. Thank you!
Thank you! I hope to make more in a couple of months
man...where are your safety glasses when using the router??? Spectacles, are not the same thing!!!
I will follow your steps except all of the safety mistakes.
Buenas y saludos desde colombia, a este modelo de sierra se le puede colocar el riel deslizante TS?
I do not know what is a TS sliding rail.
Are you still pleased with it after 2 years?
Yes. It still works well. I do recommend it.
Thank you for the video, it's great you show the mistakes so we can learn better with you!
Weaving
You are on to something
A table?
It is flat, but no legs
Can you put a dado blade on the saw?
Yes, I used a 6" dado stack in it. I think I could do an 8" too.
@@iabboud how do I remove the riving knife
@@jameslund221 checkout this video to learn how to remove the rising knife. I used an ocilating saw. kzread.info/dash/bejne/Ymilt7qcqMXNf6w.html
@@jameslund221 you have to cut the notch in the knife with a saw. Dremel or oscillating tool
Yes i had an 6" dado
An instructive film. You could still show what a cut with a factory insert looks like and how with the one with zero clearance made by you in the video. Greetings from Poland Adam
Thanks for sharing. And don’t worry about the “mistakes”, I learned from it too! Appreciate it!!!
Thank you
Great video . I am new to woodworking . I made this but my keep coming out from the back. Blade is lifting my insert so I am not using it . Can you make one for me ?
great video. Thank you.
Thank you!
Are you happy with the saw? I find lots of reviews of the older model, but nog about this one and i'm seriously in doubt between this one and the dewalt 4792 (similar but a lot more expensive). Best regards
I have been happy with it. I had it a little over a year now and have used it a lot. Has been a good investment. And for the money, you can't go wrong.
@@abboudworkshop9404 thanks for the quick response! If you ever think about making a review with your likes and dislikes, don't hesitate tot inform me 😅 Think you would help out a lot of people in Europe and i would love to share the link ;)
☕🎁 I bought this coffee maker for myself as a Christmas present and I am very happy with my purchase ! 🎁☕
I love 'em too.
Does the saw still roll over to 45^
No
Nice review!
Thank you
Learnt a lot thanks, I have the C10RJ not C10RJ(S) only difference I noticed, is mine does not have that lock for the plate, my plate locks in with a little lever on the plate itself.
Uma bela obra de arte parabéns meu amigo🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷
Have watched many board vids. This was the first one that made me actually laugh!. And you did cover all the crucial stages. Kudos.
Thank you:) I mean, what else do you need to know in a Tik tok world :) i do have a longer video on how to glue it :)
You can use the saw horse as scaffolding with a smaller board 12 x 24
I am not sure what you mean by 12x24 or how you mean to place it... Can you clarify?
When you switched the circular saw blade with the table saw blade, did you have the blade in reverse order?, I noticed the blade brand facing the wrong side and saw dust came out on your side of the table saw.
You made me look closely... it was in the correct orientation :)
Just bought 3 PAIRS of these clearance at a Lowe’s store for $13.06 PER PAIR. Score!!!
That is a fantastic deal
I did a thumbs down on the Kobalt sawhorses, not on the gentleman’s video. He did a great job, however these sawhorses seem Clunky and difficult to operate, as he said himself Bora makes a much better product!
Dude. Downvote on the Lowes home page. If he did a great job showing you the product that's what you're voting for.
Fantastic! Not only do I now know how to make my zero clearance throat plate, but I'm also happy to see someone using the same router table I use!
Glad it was helpful!
I love my Kobalt router table too! tossed my Bosch one in the junk pile.
@@TheBikersurgeon you must be joking
I have this saw, and really appreciate you posting this video. Can you please do a video detailing how you removed the riving knife??? Thanks in advance!!!
I actually saw it on another youtube video but I don't have the link handy
The only way I saw was to use a Dremel to cut the bottom of the riving knife.
Nice video, the music was a tad too loud. Whats the groove for?
The idea of the groove is that it catches the juices of whatever you are cutting up.
Awesome stuff. Keep it up man
Thanks! Will do!
You could use your fence to hold insert to make the cut instead of clamps
That would have been a good idea for me to do :)
How’s it working? Do you notice a difference in dust around the shop?
It is working well. Filter keeps getting dirty so I know it is taking the dust out of the air! I clean the outer filter every 2-3 weeks using a shop vac. The inner filter is still clean.
@@abboudworkshop9404 Thanks! And I’m enjoying your videos!
I like your attention to safety (with you camera person’s help)
Camera people are the best :)
It is very nice
I have the same saw. Thank you for the post.
How are the replacement costs for the filters?
Filers are about $24 per pair give or take. But you don't have to replace the inside filter as often.
I have been wanting to do this for my Delta saw. Congrats on starting a channel!!
Thanks Denver! Go for it! It was a fun little project and I got to learn about some intricate details about my saw in the process.
Haha, I saw you doing #1 first and was like, "Oh no! Wait for it.". What did you choose this model over the adjustable version? I heard they might not be as sturdy as this model.
Yeh, I am sure it won't be the last time I make that mistake! I chose this one because it was on sale and honestly, I don't need more strength than this. My old set were plastic ones from Harbour freight so this is a gigantic improvement!
@@abboudworkshop9404 I got in on the same sale, but if you bought it in person the deal was even better probably because it was clearence. I'm picking my set up tomorrow.
Just got me a pair. Good review. Thank you sir.