Пікірлер

• 
  @robertkwiatkoski12923 күн бұрын

  Bayliss builds a beautiful boat! Paint job doesn't do it justice. Sorry mike.

• 
  @randalldugan18173 күн бұрын

  Which model Carolina Skiff is it?

• 
  @wnd7113 күн бұрын

  ? Lake

• 
  @74nova363 күн бұрын

  Just gonna send it!!

• 
  @fireballsoutherner16 күн бұрын

  Oil contaminated with water...

• 
  @Phillipsmarine202216 күн бұрын

  Fuel has water and sludge in it

• 
  @Odinsoneye17 күн бұрын

  Why in the world did you remove all the lower components? The 2 water seals and oil seal can be replaced from the top after you removed the oil pump gears???

• 
  @Odinsoneye17 күн бұрын

  And curious why you didn't change the plastic shift rod bushing while head off?

• 
  @Phillipsmarine202217 күн бұрын

  I removed the oil pan due to fact the coupling for the oil pump drive gear had come apart and there were pieces in the oil pan I could not see so I pulled it apart to make sure I got all the pieces out.. I have done many of the water seals and oil seal I understand you can do this job with out doing what I did but I had my own reasons why I pulled it further down!!!!!!

• 
  @Phillipsmarine202217 күн бұрын

  @Odinsoneye because it was no issue I greased it and didn’t see the need to replace that

• 
  @Odinsoneye17 күн бұрын

  @Phillipsmarine2022 oh, never had that happen. Good catch

• 
  @Odinsoneye17 күн бұрын

  @Phillipsmarine2022 seems like all the 2015 L6s are having shift rod bushing problems at once. I have them lined up

• 
  @KillinTimeHuntingFishing22 күн бұрын

  What is the size of boat ?

• 
  @Phillipsmarine202222 күн бұрын

  31ft

• 
  @aaronjuan483522 күн бұрын

  Was it overheating at idle or not peeing? I have a 115 thats overheating at 4k rpm but pees fine with 0 psi water pressure. Did water pump, lower unit driveshaft seal etc. Stumped.

• 
  @Phillipsmarine202217 күн бұрын

  Did you check the popper valve it is located in the mid section behind cowlings

• 
  @user-ix2hd5ub3r26 күн бұрын

  Pitch of prop ?

• 
  @Phillipsmarine202217 күн бұрын

  Honestly I do not remember most likely a high pinch due to these have a lower rev limiter

• 
  @alexbernal498828 күн бұрын

  Hi. How to prevent it from happening? Thanks

• 
  @Phillipsmarine202228 күн бұрын

  Maintenance fresh was flush under hood 6-56 spray on shift shaft and components.

• 
  @geoffreyjakab7744Ай бұрын

  Is the Crusty Crab Restaurant still there?

• 
  @Phillipsmarine2022Ай бұрын

  It is not crusty crab any more it has new people leasing it and opened a new restaurant called harbors end

• 
  @06nemoxАй бұрын

  For the price of one, a robot should fly out when you open the hood and fix itself.

• 
  @surftherapymorocco1952Ай бұрын

  Come to Morocco 🇲🇦 😅

• 
  @nf4833Ай бұрын

  My trash can does the same thing and it was like 25 bucks.

• 
  @dmnddyАй бұрын

  that release sounds EXACTLY like my 2000 Audi’s trunk 💀

• 
  @floridaripper817Ай бұрын

  Awsome. While it works lol

• 
  @chrisroberts500Ай бұрын

  Check it out! I have so much money to spend!

• 
  @mikeshoemake6965Ай бұрын

  Well that’s about 250k..

• 
  @grimm2748Ай бұрын

  V12’s wow. Impressive

• 
  @frettbuzz1911Ай бұрын

  Finally a button auto open since that lid was so heavy 🤣🤣

• 
  @angelllamas8409Ай бұрын

  I swear at first I thought it was one of those automatic door trash cans

• 
  @sentradynamics8889Ай бұрын

  I want to pet the Loon

• 
  @terrybusinelle1771Ай бұрын

  I think he did a fantastic job

• 
  @Phillipsmarine2022Ай бұрын

  Thank you!

• 
  @colerivault5196Ай бұрын

  Where u located need some help with mine

• 
  @Phillipsmarine2022Ай бұрын

  I am on the eastern shore of maryland

• 
  @ronjohngameonАй бұрын

  Good day! I know of a Suzuki dealer that sells lots of these DF300AP from 2019 to current 2024, how crucial and how often should valve clearances be checked on these engines? These engines are normally bullet proof and the dealer has been having lots of these coming back with issues all DF300AP with cracked port side heads between valves on cylinder 4. Any feedback would be appreciated! Nice video BTW!

• 
  @Phillipsmarine2022Ай бұрын

  Should be done every 1000hrs

• 
  @user-hp1fh5hr3nАй бұрын

  This is a useless video.

• 
  @billboy95022 ай бұрын

  Music was painful

• 
  @johnhamilton92293 ай бұрын

  Sunblock to rock

• 
  @rebeltrooper02403 ай бұрын

  What year is that motor?

• 
  @Phillipsmarine2022Ай бұрын

  2004

• 
  @trentbuquoi8033 ай бұрын

  What year is that motor?

• 
  @lhfdetailing26283 ай бұрын

  Just needs a T Top

• 
  @gaetanobuttari85914 ай бұрын

  I also have a DF200 and took the prop shaft out. Unfortunately, I couldn't tell how the the spring and ball bearings went into the prop shaft. Does the spring and bearings go into the shaft first then the pin so there is always forward springed pressure of the dog clutch into the forward gear? Or, does the shift selector do all the work into forward and reverse. Thanks for the video.

• 
  @alwaysaway694 ай бұрын

  One of the most useless videos I’ve ever seen. Seriously! Why bother even uploading it? Just watched it again at slow speed. Yup! Still the worst how to video I’ve ever seen. KZread should delete crap like this.

• 
  @eastcoastangler83904 ай бұрын

  Thanks for taking the time to show others. Did you replace the silicone on the divider and what Size/pitch prop are you running and top speed?

• 
  @Phillipsmarine20224 ай бұрын

  Yes always put new silicone on the exhaust divider. As far as prop and speed I’m not sure. That job was little while ago and don’t remember prop size unfortunately

• 
  @tristanschaper2814 ай бұрын

  Great Video! It's actually amazing that this newer engine with all of the electronics, can still be flushed and fire up. Boy, that sure made a TON of steam! Mine has steam but nothing like this. Maybe it was the weather/temp/humidity when you were filming it. What sensors did you have to disconnect? Did you end up having to replace any components/sensors? Even the starter and alternator survived?

• 
  @morganmyers46034 ай бұрын

  My great uncle 87 and I have done the exact same thing. We are about to fire her up and see if this fixed it! A lot of material was found, gritting and calcified! I’ll be back to let you know if it was successful! Your video was extremely helpful!!!

• 
  @geofix5004 ай бұрын

  Do you have a full length version of this video?

• 
  @fishermansfriend61974 ай бұрын

  Hello, I have 175 ap Suzuki and never touched to the valves... 850 running hours on it. Can You show this job done littlebit (very much) slower. And if you have that inline 4 ,150-175-200 hp Suzuki , can you make new video please :) I think you use special shimming tool here? Greetings from Finland!

• 
  @Phillipsmarine20224 ай бұрын

  Yes I have a pair of 200s coming up that I will do a video on. And yea there is a special tool also you need a thin long flat head screw driver and a magnetic to catch the shim once you pop it out

• 
  @tristanschaper2814 ай бұрын

  Great video, thank you!

• 
  @ismail65005 ай бұрын

  Ini 300 bukan 250

• 
  @chadchemersin36585 ай бұрын

  That bwehwlh on start up is amazing no doubt

• 
  @tristanschaper2815 ай бұрын

  Great video, thank you! Can you elaborate on the 85 ft lbs on the "fat shaft" lowers? I have a 225 Pro XS with the For Torq SSR and it states 55 ft lbs. Do you also recommend replacing the Nylock lock nut every time, as there is no cotter pin, and it's the only thing holding the prop on, combined with the Belleville washer.

• 
  @milanqaibxanov16566 ай бұрын

  Neciyə almag olar .

• 
  @milanqaibxanov16566 ай бұрын

  Salam satılır.

• 
  @trumpet17836 ай бұрын

  the engine has been standing for 4 years and has 550 hours..the problem was in the white wire, but I solved that and the engine started. I started it for a few days for 10-15 seconds and everything was fine and now it won't anymore..the pump works but there is no spark..it gives me the error 2 4 CMP sensor..bought a new one and the same thing..I doubt if the chain can skip? I would like to check that but I don't know how? what positions should be on the FLYWHEEL COVER and on the hole when the CMP sensor is removed? Th

• 
  @tybrady89126 ай бұрын

  Why do so many American boat companies supply their boats japanese outboards. We invented the outboard!!!

• 
  @hankd19186 ай бұрын

  Most NGKs don’t take antiseize per recommendation from manufacturer

• 
  @roquemarcos46596 ай бұрын

  Tem que andar com barco tanque atrás 😂😂😂😂

• 
  @pascualperrino40716 ай бұрын

  excelent video

• 
  @jonathonstapels76567 ай бұрын

  Wondering if this boat is trailerable with the wrap on or if the wind would tear it off?

• 
  @Phillipsmarine20227 ай бұрын

  I’ve had boats go from my place on eastern shore to California and make it there with everything still intact. This boat actually traveled 35 miles to its owners places at 60mph and still intact so really never had an issue with them coming apart in the wind or travel if they are done correctly.