Пікірлер

• 
  @tubaduk4 күн бұрын

  There’s no way this is 200 % efficacy, first thing you increasing the back pressure on “death gas” which is soooo bloody dangerous, also increasing back pressure reduces efficacy

• 
  @dr_faizanali7 күн бұрын

  What are these filters? What material should be inside.

• 
  @theaussienurseflipper.81138 күн бұрын

  Interesting video mate, why do you have the gas going against the flow through the filters and not following the arrows. Cheers Graham

• 
  @user-pv4ld1je5x17 күн бұрын

  Very good video s. Learn alot from you guys. Take care from Ontario. ❤❤

• 
  @vidili6818 күн бұрын

  Hi there Did see it work 👎👎👎👎👎👎🇺🇸

• 
  @andrewbutler639019 күн бұрын

  That's a terrible soundtrack!

• 
  @SpYucaipaSoCal21 күн бұрын

  Could use a coil of any metallic tubing for the radiator and small fan to push air past it. Or the coil in a box and push output air from heater. Or the heat exchanger from a home furnace.

• 
  @dayleedwards352121 күн бұрын

  That is not a 200 percent efficiency at all. The exhaust gas can only heat a small section of your radiator, the bottom remains cold, indicating the hot exhaust gas flow is small. Yes, you are recovering a little more heat, but certainly not the amount you hoped for. To achieve a 100 percent increase over the 5 kW initial output would require another 5kW of exhaust heat, they do not waste this amount ever.

• 
  @57energon22 күн бұрын

  I wonder if you can recirculate room air to heat through your cast iron radiator. I mean holding the heat yes. However removing the heat into the room using other than natural convection.

• 
  @thenextpoetician6328Ай бұрын

  Well, look what the algorithm offered up. In case you read comments from older videos, you should have at least one off-sight cold-storage drive, one on-sight, and a couple of warm-storage drives, and the working drive where nothing is stored. VOE. ;)

• 
  @dustinfrost5214Ай бұрын

  Good idea but what happens when its all clogged up

• 
  @57energon22 күн бұрын

  Flush out the radiator with water or even brush it out woth the ends removed.

• 
  @STRUTZKOFFКүн бұрын

  @@57energonyou cant with this style

• 
  @mainlittlerock5422Ай бұрын

  I liked (not "looked"... edited) watching you create this most handy device. My pasture is filled with river rock & our gophers & voles keep pushing them to the surface. I've only got a few undamaged windows left. Lol. It would have been more enjoyable for me without the music or maybe just set at a lower volume, because I struggled to hear & understand you many times throughout the video... just my opinion. Your implement definitely turned out beautiful. Very nice skills & finish work! I hope you're enjoying easier potato pickins.

• 
  @willfromthevalleyАй бұрын

  what if you put a smaller radiator , like small car or motor bike boxed it up and made ducting so heater outlet blows through it duct ==< rad >== duct= =heater if that makes sense

• 
  @TheTorkermanАй бұрын

  You made a fantastic thing! Enjoyed watching

• 
  @yousircantknow8987Ай бұрын

  What a pointless video.

• 
  @daviddavis6231Ай бұрын

  The set up in my conservatory is much the same ,with the exaust going through a normal radiator ,very little heat wasted . I dont know why most folks put the heaters on the outside,

• 
  @davidpatrick1813Ай бұрын

  Where is the 200% more efficient time stamp?

• 
  @k9roadАй бұрын

  ...meaning, if you can fit a kettle you will have hot water... nice one..

• 
  @k9roadАй бұрын

  Hi there, I am very interested in this improvement. Now after 4 months, I would love to know, did you alter anything or is it running fine as is? Many thanks and Greeting from Ireland.

• 
  @drpipeАй бұрын

  Get a carbon monoxide detector in the space

• 
  @bradrowe7131Ай бұрын

  Battery under exhaust outlet , lot of heat generated there

• 
  @joeleon5617Ай бұрын

  Thanks! I love it

• 
  @electricalfive22482 ай бұрын

  if anyone wants a cheap super simple way to extract heat from the exhaust, just buy a pack of scotch bright stainless steel scrubbers. You can expand them from the middle and slip them onto the exhaust pipe. They have a ton of surface area and conduct heat from the pipe really well. they work pretty well already by passive heating, but you can add a fan to help a little. You can buy a 16 pack for $10. Thats all you need.

• 
  @harryphotos1Ай бұрын

  Nice idea

• 
  @mystic241002 ай бұрын

  I volunteer to drive the tractor.

• 
  @fido83662 ай бұрын

  And how it works...😢

• 
  @kennethtibbitts4142 ай бұрын

  awesome idea

• 
  @DougAlft2 ай бұрын

  I'm curious about where you got the fire box.

• 
  @jeanlefebvre64582 ай бұрын

  What’s your address I’d love to go visit this summer I have a small camping trailer I could camp close to your place thanks again write to me in private

• 
  @jeanlefebvre64582 ай бұрын

  That’s a great idea réal happy thanks

• 
  @jeanlefebvre64582 ай бұрын

  Can make me couple stone and 1 bushing

• 
  @dsfarmns28232 ай бұрын

  Use this email and tell me exact what you want [email protected]

• 
  @user-cj4to2us2i2 ай бұрын

  The one fault with the system is that the heater and exhaust pipe is below the entrance to the radiator creating a trap for moisture

• 
  @tomvanthienen37162 ай бұрын

  Indeed...I have the same system..my heater is placed outside in a plastic nice box and the exhaust pipe is coming in at the top of the radiator and goes out at the bottem. My heater is at the highest point and the exhaust pipe is running down so water can run out at the bottom of the radiator.

• 
  @harryphotos1Ай бұрын

  Yes exactly, everything has to flow downhill or you could have water build up and flow restriction.

• 
  @anttik8191Ай бұрын

  That exitpipe is so hot that it will vaporize any water/moisture there

• 
  @mistercab072 ай бұрын

  Muy bueno, pero me gustaría poder construir uno igual en mi país (Panama), y faltan las medidas para hacerlo.... muchas gracias

• 
  @niklar552 ай бұрын

  The back pressure on the exhaust could cause problems. You need to keep a check on the heater. .

• 
  @tomvanthienen37162 ай бұрын

  With that system , I also use it there is no problem with back pressure. The exhaust air can run free thru the radiator..no problem at all. The connection are all 3/4 and the are a fine bit bigger then the exhaust pipe that is 1mm smaller.

• 
  @niklar552 ай бұрын

  @@tomvanthienen3716 I have no idea of the exhaust size, but it is the resistance to the exhaust that can cause a problem, by slowing gas flow..

• 
  @patricklavery5144Ай бұрын

  @@niklar55 Would be a better idea to have the inlet at the bottom of the rad as heat naturally rises and will have less resistance

• 
  @MrAzulikit2 ай бұрын

  If the heat tape was temporary. What are you using now to connect the end of the exhaust to the radiator piping?

• 
  @quintonduplessis6052 ай бұрын

  Please mute the radio in the background cant hear anything you say. Bye

• 
  @user-mg5mh2jl9u2 ай бұрын

  If there's something you don't want to do with a combustion heater, it's to obstruct the exhaust. Smothering the exhaust can lead to disaster sooner or later. You must ensure that exhaust fumes can easily and without restriction exit the building. If you wish to recover some heat, attach a vertical chimney to your diesel heater. Do not reduce the diameter of the chimney!

• 
  @joachimschreiber78352 ай бұрын

  i totally get the concept. but: 1) why make the inlet so far up that you need a chair to fill it? 2) how do you get the gas into a storage container like a rubber boat, a truck tire-hose or a big PVC Baloon? 3) why is there no shutter in the input or fertilizer extraction pipe to keep gas from escaping or creating explosive atmosphere with incoming atmospheric air? thx!

• 
  @Herzeleydt_Diesentrueb3 ай бұрын

  Where is that smell of sowercrowt coming from ?

• 
  @donhutton26413 ай бұрын

  I don’t think diesel heaters make sense, unless you can use red diesel, that is for off-road vehicles. No road taxes built in. Also, the noise, and the ticking would bug me lol. I use a heat pump in my garage. Quiet, efficient.

• 
  @tsi87supr603 ай бұрын

  🤔 pluming it through the top and exhausting at the bottom. You are losing 90% of the heart Plum the entry to the radiator at the bottom and exhaust at the top. That way way it heats the entire radiator before exhausting.

• 
  @bsimpson62043 ай бұрын

  Heat rises so to keep the heat in the radiator feed the hot exaust in top left, this makes the hot gases pass through the radiator giving up it's heat before escaping bottom right

• 
  @tomvanthienen37162 ай бұрын

  No...the water needs to go from the top to the bottom or else your radiator will fill up with condense water.

• 
  @harryphotos1Ай бұрын

  As stated, you can't do that because water will collect.

• 
  @ebrassy3 ай бұрын

  why don't you use a diesel generator and cool it with your radiator from inside the house and while you make electricity

• 
  @tslim2503 ай бұрын

  you could totally do this too but a generator won't really produce a ton of heat

• 
  @brucea5503 ай бұрын

  You’re adding heat storage instead of just warming air directly, so maybe more efficient that way but the heater’s efficiency didn’t change. You just added thermal mass.

• 
  @joachimschreiber78352 ай бұрын

  only if he added the radiaor on the OUTLET. but he added it on the EXHAUST which gives indeed extra heat that woud normally be lost.

• 
  @brucea5502 ай бұрын

  @@joachimschreiber7835 yup, I skipped through it too fast and missed that detail. Wonder how much soot will build up in the radiator over time? Otherwise a good idea.

• 
  @ralph18812 ай бұрын

  ​@@brucea550would matter more if it still had liquid flowing in it...but just exhaust air will last longer without issues.

• 
  @EdwardVanNatta3 ай бұрын

  Iam looking for about your products place lace me a massage.when I post this, I am looking for more information on this. Work small a little tiny house for a houseboat or a shipping container

• 
  @madwaxer833 ай бұрын

  ❤ I'd propose to turn the heat exchange sideways or flat. to allow the soot to flow out from the radiator coils and prevent long-term use blockage. thanks for your experiment ❤

• 
  @dncook19553 ай бұрын

  Great idea. Good thinking on putting inlet at top so that condensables can drain out the bottom.

• 
  @MrBobWareham3 ай бұрын

  Input should be at the bottom as heat rises!!

• 
  @camillosteuss3 ай бұрын

  not per se... if you put it at the bottom, and have a forced air from the furnace, then the inlet at the top forces the hot air to go down the radiator due to increasing pressure, thus extracting more heat from the air... If the inlet is at the bottom, then the hot air just naturally surges upwards to the exit hole, extracting less heat from the air... Generally what you say is true, but not categorically...

• 
  @tslim2503 ай бұрын

  the heated air is being cooled, cooler air falls.

• 
  @tomvanthienen37162 ай бұрын

  Not with this system...the condens water needs to fall down and exit at the bottom.

• 
  @rjright73733 ай бұрын

  Good job, I would have bought the metal pipe from a recycling yard for a few bucks tho. Where I’m at we can wander a bit around the yard, pick things up, put them on the scale and pay double or triple what they buy it for, much better than buying from a retail store. @ $250/ton #1 steel it makes that 4lbs of steel worth a few bucks at best.. Cheers!

• 
  @stevenstiles51123 ай бұрын

  Loved the video. Thanks.

• 
  @jimmytate75873 ай бұрын

  are you using indoor air for combustion?

• 
  @daveunderwood64983 ай бұрын

  Now that is an awesome idea! If you find you need more heat at the griddle, you can insulate the pipe.

• 
  @daveunderwood64983 ай бұрын

  I have to say that this is one of the best ideas I have seen on KZread. Of course condensation will form in the rad, but being cast iron and the exhaust low, it will drip out the bottom. Those heaters burn so efficiently that you won't have to worry about soot collecting in the rad. To test for this possibility, when it's new, record the temperature drop from top of rad to the bottom. After running it for months, or years, keep testing the temperature difference. If soot is forming on the inside of the rad, the temperature difference will become less. The exhaust temperature, at the floor will increase. The soot will act as an insulation. I can't see that happening though because of the burn efficiency. I only thing I would do differently is a more positive, sealed connection between the iron pipe and the heaters' flex line. Easy fix. As for the haters in the comment section, these people are shocking ignorant to basic science. You can tell they have done nothing in life. Nice job. It has given me some ideas.👍

• 
  @grahammaclure57226 күн бұрын

  I totally agree with @daveunderwood6498. The only comment I would make, and I'm being picky , are the 90 degree elbows but they do save space and that's the only a minor restriction .