The Slipstream S-03 windshield used to mount differently on my 1992 750 Nighthawk, so I had to watch your video to make sense of the new instructions. The brackets used to attach to the headlight bracket bolts on the fork, the windshield was positioned in front of the brackets, and the mounts on the handlebars used to be rotated 180 degrees so the thumbscrews were facing the back of the bike. Why they can't include photos of the way it's supposed to be mounted in the instructions, rather than paying someone to drawing confusing diagrams, makes no sense to me. Thanks for the video.
@tylerm12418 күн бұрын
Will it pull just an inner race?
@GaryFiАй бұрын
Had the same exact bike (minus the fairing) back in ‘82. Rings back a lot of memories, thanks!
@chadbinette32013 ай бұрын
My dad had this exact bike when I was kid, same color and all.
@ibdribbles71283 ай бұрын
Loopy thing? Dude, you’re killing me
@robinhood90365 ай бұрын
Why do i not see that cable in the engine bay for my o2 sensor? I pulled the black cover off but the place where your connector is mine is empty
@kaikourasunshine72058 ай бұрын
Hi! Is this safe for the rod bearing? I need to do this in my Rotax max.
@mustaphaessahihi17629 ай бұрын
Hi is there any new video about this project I am thinking about turning my bike into electric
@dinot719 ай бұрын
Do you know if 1 Liter of oil is enough to do both rear shocks?
@jimbyrne90719 ай бұрын
Thx Marty your videos are a great help im starting on my 74B
@FightFilms10 ай бұрын
$20? I buy those seals in Ecuador for a buck, each. Crazy.
@jesusvillalobos657711 ай бұрын
Where did You Buy it at??
@Corn-ped11 ай бұрын
You finish this yet?
@rosesbite Жыл бұрын
nobody knows :)
@latinrider1809 Жыл бұрын
where did you buy it at,..???
@jimbyrne9071 Жыл бұрын
Nice work Marty
@kbcamino7693 Жыл бұрын
I’m so confused. How do the spacers go on???
@BaconGampo6 ай бұрын
Through the hole that the long bolt goes in on the subframe
@motogstylus3260 Жыл бұрын
Any feedback on how this hitch held up?
@LukeSkywalker-zn1xv Жыл бұрын
Don't u need electrical installation for the trailer brakes lights just wondering or you can just get away with no lights
@SCOTTYD-gz9qm Жыл бұрын
After this video the MG was never seen again
@timromano7085 Жыл бұрын
You skipped over the hardest part: putting the hitch onto the bolts without knocking the bolts out. Any tips on doing that without someone helping?
@michaelmaxwell568 Жыл бұрын
The whole front fairing is missing
@litocordova9753 Жыл бұрын
Todavía la tienes? Vendemela $$
@thequadzillaking Жыл бұрын
I had one in ‘89. Awesome dash/gauge cluster. My friends liked it. Crashed into Cadillac. Had for 2 years.
@mariestick6636 Жыл бұрын
nice
@rickrandom6734 Жыл бұрын
It would look better with round headlight. Of course you had to get rid of the original tank and side panel, and replace them with nice ones to make it look good. Probably seat would not fit then.
@eduardodias4661 Жыл бұрын
Hello, Is one complete revolution of the tool equal one millimeter? thank you
@No_Malarky Жыл бұрын
U-joints are great little implements in conjunction with the extension of choice.
@alexjimenez732 жыл бұрын
According to specifications I found on the internet the engine has only 54 HP. This is true? The question is why there is a huge difference to the competitors of the time. CBR had 85.
@Hpynos2010 Жыл бұрын
The FZ 600 had a simpler engine design, air-cooled with 2 valves per cylinder and smaller carbs. The CBR and other competitors sported bigger carburetors, liquid cooling and 4-valve engines that made substantially more power. The FZ was quite simply outgunned in the horsepower wars.
@alexjimenez73 Жыл бұрын
@@Hpynos2010 You're right. But what a strange strategy from Yamaha. They used the XJ series engine (standard bikes) in a race replica and, instead of increasing the power, they reduced it.
@Hpynos2010 Жыл бұрын
@@alexjimenez73 The FZ600 was based on the 1987 Japanese market FZ400. The FJ600-based air-cooled engine (with its smaller carbs) was the only thing around at the time that would fit the small confines of that frame.
@Marv_rvpe_u2 жыл бұрын
Do they fit with the stock Bosch flywheel?
@danielgirouard32872 жыл бұрын
Frein avant
@alexsfetcu9462 жыл бұрын
did you fix it ? I am so curious, i have same problem as you. I think it might be the clutch, was it the clutch ?
@triedandtruefoo2 жыл бұрын
Do you still have the MG? Cool video. I'm putting my 78 MGB wipers on a toggle switch.
@puch27282 жыл бұрын
Thanks for showing us how to use this tool. I never found any videos explaining how. Now I found out.
@pnw_element98222 жыл бұрын
Thanks I did mines today very easy after watching this
@rtchow30002 жыл бұрын
first off, i want to thank Marty for his great tips on MG classic! you all are welcome to go my youTube channel check out my 1971 MGB/GT without the filter housing. I do miss the MGA, love the beautiful body style. I never own an MGB, only this GT. Other British made were the 1957 and the '58; Austin Healey Sprite.
@fzdreamz87362 жыл бұрын
Did you get it figured out?
@thomasgronek64692 жыл бұрын
dip it in a tub of water, , , If it stalls, it has a leak
@milojanis73762 жыл бұрын
Hi do you stick the spacers to the frame first or put them in position first ? Does any one know
@xrtgx222 жыл бұрын
Hey, I’ve been thinking about converting my Vespa Grande to electric. Roughly how much have you spent on the conversion?
@historichomestead2 жыл бұрын
Why convert it? The Grande is a great moped. And with a few cheap upgrades can do 45 and climb some pretty good hills with a 234 pound rider. And gas is a whole lot quicker to get you back on the road than batteries.
@canuckfixit77222 жыл бұрын
Can a kit like this also be used in reverse fashon to "pull" bearings and gears back on instead of using a hydraulic shop press?
@joshmeyer52803 жыл бұрын
How bad was it to fit the polini kit and was the power gain noticable?
@juanvillalobos20843 жыл бұрын
I know this video is old but I have a 2001 Volvo v40 1.9t where is bank 1 sensor 1
@channelfransiskus92173 жыл бұрын
hai ! saya menyukai video ini alat pembuka berings membuat saya terinsfirasi untuk membuat sesuatu
@runandplay3 жыл бұрын
Second of three motorcycles in my life. This is the one that gave me fin marks on my inner thigh. Damn front caliper.
@MrCamwow3 жыл бұрын
Floppy thing tube spacer things loopy things gold tooth washers 😂😂👍🏻👍🏻👍🏻
@sayit43693 жыл бұрын
Thank you, very helpful on what hitch to purchase and DIY installation.
@bernardmauge66283 жыл бұрын
Douche!
@RandallChase13 жыл бұрын
My front end was squeaky thinking I need to add oil.
@stratac303 жыл бұрын
Install the harness from the engine side. if you can, it would be useful to have a helper in the cockpit to help pull it through.
Пікірлер
The Slipstream S-03 windshield used to mount differently on my 1992 750 Nighthawk, so I had to watch your video to make sense of the new instructions. The brackets used to attach to the headlight bracket bolts on the fork, the windshield was positioned in front of the brackets, and the mounts on the handlebars used to be rotated 180 degrees so the thumbscrews were facing the back of the bike. Why they can't include photos of the way it's supposed to be mounted in the instructions, rather than paying someone to drawing confusing diagrams, makes no sense to me. Thanks for the video.
Will it pull just an inner race?
Had the same exact bike (minus the fairing) back in ‘82. Rings back a lot of memories, thanks!
My dad had this exact bike when I was kid, same color and all.
Loopy thing? Dude, you’re killing me
Why do i not see that cable in the engine bay for my o2 sensor? I pulled the black cover off but the place where your connector is mine is empty
Hi! Is this safe for the rod bearing? I need to do this in my Rotax max.
Hi is there any new video about this project I am thinking about turning my bike into electric
Do you know if 1 Liter of oil is enough to do both rear shocks?
Thx Marty your videos are a great help im starting on my 74B
$20? I buy those seals in Ecuador for a buck, each. Crazy.
Where did You Buy it at??
You finish this yet?
nobody knows :)
where did you buy it at,..???
Nice work Marty
I’m so confused. How do the spacers go on???
Through the hole that the long bolt goes in on the subframe
Any feedback on how this hitch held up?
Don't u need electrical installation for the trailer brakes lights just wondering or you can just get away with no lights
After this video the MG was never seen again
You skipped over the hardest part: putting the hitch onto the bolts without knocking the bolts out. Any tips on doing that without someone helping?
The whole front fairing is missing
Todavía la tienes? Vendemela $$
I had one in ‘89. Awesome dash/gauge cluster. My friends liked it. Crashed into Cadillac. Had for 2 years.
nice
It would look better with round headlight. Of course you had to get rid of the original tank and side panel, and replace them with nice ones to make it look good. Probably seat would not fit then.
Hello, Is one complete revolution of the tool equal one millimeter? thank you
U-joints are great little implements in conjunction with the extension of choice.
According to specifications I found on the internet the engine has only 54 HP. This is true? The question is why there is a huge difference to the competitors of the time. CBR had 85.
The FZ 600 had a simpler engine design, air-cooled with 2 valves per cylinder and smaller carbs. The CBR and other competitors sported bigger carburetors, liquid cooling and 4-valve engines that made substantially more power. The FZ was quite simply outgunned in the horsepower wars.
@@Hpynos2010 You're right. But what a strange strategy from Yamaha. They used the XJ series engine (standard bikes) in a race replica and, instead of increasing the power, they reduced it.
@@alexjimenez73 The FZ600 was based on the 1987 Japanese market FZ400. The FJ600-based air-cooled engine (with its smaller carbs) was the only thing around at the time that would fit the small confines of that frame.
Do they fit with the stock Bosch flywheel?
Frein avant
did you fix it ? I am so curious, i have same problem as you. I think it might be the clutch, was it the clutch ?
Do you still have the MG? Cool video. I'm putting my 78 MGB wipers on a toggle switch.
Thanks for showing us how to use this tool. I never found any videos explaining how. Now I found out.
Thanks I did mines today very easy after watching this
first off, i want to thank Marty for his great tips on MG classic! you all are welcome to go my youTube channel check out my 1971 MGB/GT without the filter housing. I do miss the MGA, love the beautiful body style. I never own an MGB, only this GT. Other British made were the 1957 and the '58; Austin Healey Sprite.
Did you get it figured out?
dip it in a tub of water, , , If it stalls, it has a leak
Hi do you stick the spacers to the frame first or put them in position first ? Does any one know
Hey, I’ve been thinking about converting my Vespa Grande to electric. Roughly how much have you spent on the conversion?
Why convert it? The Grande is a great moped. And with a few cheap upgrades can do 45 and climb some pretty good hills with a 234 pound rider. And gas is a whole lot quicker to get you back on the road than batteries.
Can a kit like this also be used in reverse fashon to "pull" bearings and gears back on instead of using a hydraulic shop press?
How bad was it to fit the polini kit and was the power gain noticable?
I know this video is old but I have a 2001 Volvo v40 1.9t where is bank 1 sensor 1
hai ! saya menyukai video ini alat pembuka berings membuat saya terinsfirasi untuk membuat sesuatu
Second of three motorcycles in my life. This is the one that gave me fin marks on my inner thigh. Damn front caliper.
Floppy thing tube spacer things loopy things gold tooth washers 😂😂👍🏻👍🏻👍🏻
Thank you, very helpful on what hitch to purchase and DIY installation.
Douche!
My front end was squeaky thinking I need to add oil.
Install the harness from the engine side. if you can, it would be useful to have a helper in the cockpit to help pull it through.