Un Cuarto de HORA de Vídeo = 15 minutos, para ver como enchapa, un Corte de Ala de/en FOAM.
@Chris-vc1dh Жыл бұрын
what glue is that please?
@changoav1860 Жыл бұрын
what glue do you use?
@tzachus2 жыл бұрын
Dear sir lovely work, how do you conect both half wind together with dihedral?
@spammerscammer2 жыл бұрын
I wouldn't buy into the carbin fiber info you heard. Carbon fiber gets its strength from multiple cross hatched layers held together with epoxy. Better off using just Monikote or typical laminating film.
@kielabkh19584 жыл бұрын
It great 👍 🙏❤️🛎❤️❤️❤️❤️
@redbaron19541005 жыл бұрын
is balsa sheeting a couple of pieces glued together
@redbaron19541005 жыл бұрын
what is thickness ok balsa sheeting
@dirkgrobler21795 жыл бұрын
Where is the rest of the video?
@jaimecrespimiralles26855 жыл бұрын
Hi from spain, what kind of glue do you use in order yo joint the balsa to the foam core ¿?
@user-tk9ug2rj3z5 жыл бұрын
ចង់ធ្វើយន្តហេាះដែររៀននៅណាពួ
@marceloferreira65635 жыл бұрын
friend you make helicopter blades? you send pro Brazil? I'm crazy wanting one of these
@ginoalongi13746 жыл бұрын
ciao Joe, what brand and type of glue do you use?
@michaelupton15036 жыл бұрын
Common sense stuff I had never thought of. The compass and the way you used it to mark the lightening holes.
@NickSmith-hv9zi6 жыл бұрын
I have a set of similar foam balsa covered wings. Too heavy and wounder if there is an easy way to cut holes to lighten the wing.
@jdj624646 жыл бұрын
What brand and type of glue do you use?
@pratimatripathy66117 жыл бұрын
can man fly with these wings?
@wdlima7 жыл бұрын
What material is this dark that you cut at the beginning of the video? thanks..
@XFBO3 жыл бұрын
carbon fiber veil, lightweight material that adds a bit of strength to wing.
@joedunnaway8 жыл бұрын
The Adhesive is Elmers Glue All - it is a polyurethane adhesive activated by moisture.
@ThomasGreenhill8 жыл бұрын
What thickness balsa is this?
@camaro920266 жыл бұрын
Thomas Greenhill 3/32
@joedunnaway47284 жыл бұрын
16th inch Balsa... There are 4 more videos prior to this one showing sheeting and foam core preparation.
@x.a.m19602 жыл бұрын
I'am no balast you balast?
@f_nc8 жыл бұрын
i just destroyed one fully due to reverse connection of the aeleron servos. so this is good job, good landing.
@joedunnaway8 жыл бұрын
The carbon fiber is .007 unidirectional carbon laminate available through ACP Composites.
@joedunnaway8 жыл бұрын
Hi Dave... I usually install aileron hinge line as 2 quarter inch pieces in the foam before I sheet the wing. I mark the hinge line with a T-Pin at each end of the hinge line, cut off so they just protrude through the balsa skin. After the sheeting glue has dried, you can line up a straight edge with the pins and cut through the skin on both sides to free up the aileron.
@aircreative4 жыл бұрын
Hi broo.use wayer for whats?
@kmekrine11698 жыл бұрын
What kind of carbon fiber material are you using?
@joedunnaway8 жыл бұрын
The Carbon Veil weighs .3 oz per yard and is available through ACP Composites.
@davidsanford40798 жыл бұрын
How do you create, prepare, and install the control surfaces on your balsa covered foam core wings?
@Dionatronics8 жыл бұрын
Great video, thank you for uploading it! Couple questions....What kind of fiberglass and and casting resin are you using? What are you going to coat the balsa with?
@joedunnaway8 жыл бұрын
The wing can be fiberglassed and painted after sheeting but I usually cover the wings with Monokote. The wing shown in this video ended up weighing 11.9 oz with a JR 9411 servo and linkage (Ready to Fly).
@lookylou63332 жыл бұрын
can the wing be repaired after a crash if the 2 halves fit ? if so how?
@giffy57759 жыл бұрын
3:03 balsa dust cough, I know it well.
@gripchion9 жыл бұрын
Hey Joe did u see the alien spacecraft at about 2:34:)
@yasmanimartinez41179 жыл бұрын
Hello! Can you help me to send a plan over what I need. Or were on the Internet I can download? ? ? ? ? ? ? ? ? ? ? ? ?
@mohamednacir79898 жыл бұрын
+Moh e amed Nacir
@gripchion9 жыл бұрын
Good job Joe!
@sumerianrcpilot888910 жыл бұрын
Hi Joe, You are so professional in what you do this videos are so inspiring man. Thanks for posting them.
@yeahitworks10 жыл бұрын
nice. are you using precision leadscrew? or just screw rods from hardware store?
@BobiR-bl9fc11 жыл бұрын
awesome job ,,
@Heyemeyohsts12 жыл бұрын
HAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAha hahaha HA HA !!! HAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaH!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
@sbtflyhi12 жыл бұрын
Love your building style. I'd love to see how you put the skin on now that the wing and skins are prep'd also how you open the skin for the servo and separate the aileron from the wing.
@solkim13312 жыл бұрын
I especially liked the spar preparation/installation thanx again
@kielabkh19584 жыл бұрын
solkim13 hi brother please how are you ❤️🙏❤️🛎☝️
@solkim13312 жыл бұрын
Hi Joe, that's very impressive .You 've got some very nice machinery there.I made a small handheld version but I could use that large one that cut out that rod shape .Your is very nice very professional. Loads of useful information and tricks of the trade. Keep up the good work Miki
@Lawiah012 жыл бұрын
My build differs slightly, by keeping as much 'Grain' as possible running the length of the Wing.
Great video's , did you post the part of finishing the cuts after the sheeting ? like how you cut the ailerons ?
@joedunnaway13 жыл бұрын
I'm using GMFC.
@monkeyking11413 жыл бұрын
nice! which software do you use to control the cnc?
@gripchion13 жыл бұрын
Your shop is alot cleaner than normal Joe HAHAHAHA!
@gripchion14 жыл бұрын
Joe wrecked in the beans. Maybe by only about 2 inches, but he did touch the beans!!!!!!
@rlbrining14 жыл бұрын
The only damage was the left wheel pant that was broken by a large weed just before the plane came to a stop! Joe just plugged in the ailerons and flew it again. lol Good example of how skill and a little (or maybe a LOT) of good luck can sometimes overcome carelessness! :)
@TejasRCpilot14 жыл бұрын
mark went bipe and electric.....never thought he'd go electric
Пікірлер
Un Cuarto de HORA de Vídeo = 15 minutos, para ver como enchapa, un Corte de Ala de/en FOAM.
what glue is that please?
what glue do you use?
Dear sir lovely work, how do you conect both half wind together with dihedral?
I wouldn't buy into the carbin fiber info you heard. Carbon fiber gets its strength from multiple cross hatched layers held together with epoxy. Better off using just Monikote or typical laminating film.
It great 👍 🙏❤️🛎❤️❤️❤️❤️
is balsa sheeting a couple of pieces glued together
what is thickness ok balsa sheeting
Where is the rest of the video?
Hi from spain, what kind of glue do you use in order yo joint the balsa to the foam core ¿?
ចង់ធ្វើយន្តហេាះដែររៀននៅណាពួ
friend you make helicopter blades? you send pro Brazil? I'm crazy wanting one of these
ciao Joe, what brand and type of glue do you use?
Common sense stuff I had never thought of. The compass and the way you used it to mark the lightening holes.
I have a set of similar foam balsa covered wings. Too heavy and wounder if there is an easy way to cut holes to lighten the wing.
What brand and type of glue do you use?
can man fly with these wings?
What material is this dark that you cut at the beginning of the video? thanks..
carbon fiber veil, lightweight material that adds a bit of strength to wing.
The Adhesive is Elmers Glue All - it is a polyurethane adhesive activated by moisture.
What thickness balsa is this?
Thomas Greenhill 3/32
16th inch Balsa... There are 4 more videos prior to this one showing sheeting and foam core preparation.
I'am no balast you balast?
i just destroyed one fully due to reverse connection of the aeleron servos. so this is good job, good landing.
The carbon fiber is .007 unidirectional carbon laminate available through ACP Composites.
Hi Dave... I usually install aileron hinge line as 2 quarter inch pieces in the foam before I sheet the wing. I mark the hinge line with a T-Pin at each end of the hinge line, cut off so they just protrude through the balsa skin. After the sheeting glue has dried, you can line up a straight edge with the pins and cut through the skin on both sides to free up the aileron.
Hi broo.use wayer for whats?
What kind of carbon fiber material are you using?
The Carbon Veil weighs .3 oz per yard and is available through ACP Composites.
How do you create, prepare, and install the control surfaces on your balsa covered foam core wings?
Great video, thank you for uploading it! Couple questions....What kind of fiberglass and and casting resin are you using? What are you going to coat the balsa with?
The wing can be fiberglassed and painted after sheeting but I usually cover the wings with Monokote. The wing shown in this video ended up weighing 11.9 oz with a JR 9411 servo and linkage (Ready to Fly).
can the wing be repaired after a crash if the 2 halves fit ? if so how?
3:03 balsa dust cough, I know it well.
Hey Joe did u see the alien spacecraft at about 2:34:)
Hello! Can you help me to send a plan over what I need. Or were on the Internet I can download? ? ? ? ? ? ? ? ? ? ? ? ?
+Moh e amed Nacir
Good job Joe!
Hi Joe, You are so professional in what you do this videos are so inspiring man. Thanks for posting them.
nice. are you using precision leadscrew? or just screw rods from hardware store?
awesome job ,,
HAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAha hahaha HA HA !!! HAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaHAHAhaH!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Love your building style. I'd love to see how you put the skin on now that the wing and skins are prep'd also how you open the skin for the servo and separate the aileron from the wing.
I especially liked the spar preparation/installation thanx again
solkim13 hi brother please how are you ❤️🙏❤️🛎☝️
Hi Joe, that's very impressive .You 've got some very nice machinery there.I made a small handheld version but I could use that large one that cut out that rod shape .Your is very nice very professional. Loads of useful information and tricks of the trade. Keep up the good work Miki
My build differs slightly, by keeping as much 'Grain' as possible running the length of the Wing.
┏━━┳━━┳━┳━━┓ ┃┏┓┃┏━┫┏┻┓┏┛ ┃┗┛┃┗┓┃┗┓┃┃ ┃┏┓┫┏┛┗┓┃┃┃ ┃┗┛┃┗━┣┛┃┃┃ ┗━━┻━━┻━┛┗┛
Great video's , did you post the part of finishing the cuts after the sheeting ? like how you cut the ailerons ?
I'm using GMFC.
nice! which software do you use to control the cnc?
Your shop is alot cleaner than normal Joe HAHAHAHA!
Joe wrecked in the beans. Maybe by only about 2 inches, but he did touch the beans!!!!!!
The only damage was the left wheel pant that was broken by a large weed just before the plane came to a stop! Joe just plugged in the ailerons and flew it again. lol Good example of how skill and a little (or maybe a LOT) of good luck can sometimes overcome carelessness! :)
mark went bipe and electric.....never thought he'd go electric
Thanks Joe!
Looks good Joe thanks for all the help!