Пікірлер

• 
  @HamzehJazzar4 күн бұрын

  i keep getting this error although i tried 5 different tutorials Firmware Version: 0x0 = (unknown) WARNING: Communication failure, is the MFRC522 properly connected? Scan PICC to see UID, SAK, type, and data blocks...

• 
  @HamzehJazzar4 күн бұрын

  I KEEP GETTING THIS ERROR I TRIED 5 TUTORIALS SO FAR 7 HOURS OF MY LIFE WASTED PLEASE HELP MEEEEEEEEEE I UNINSTALLED AND REINSTALLED ARDUINO, FIXED THE WIRING, AND TRIED EVERYTHING PLEASE HELPPPP Firmware Version: 0x0 = (unknown) WARNING: Communication failure, is the MFRC522 properly connected? Scan PICC to see UID, SAK, type, and data blocks...

• 
  @ufa6218 күн бұрын

  Will this be able to handle 120v 60hz 11.8A ?

• 
  @IllInformedHuman8 күн бұрын

  120V*11.8A=1,416W Which is greater that the 175W this unit is capable of supplying.

• 
  @ufa6217 күн бұрын

  @@IllInformedHuman thank you

• 
  @wwulftange21 күн бұрын

  best video on the internet tbh

• 
  @matthewgaines1024 күн бұрын

  Leaving the wipers up is convenient but the loss of it isn’t the end of the world. You can have your wipers up or remote start but not both. The wiper spring isn’t designed for long term extension. They will stretch over time. There is a wiper park procedure in the manual that you’re not using and should be used if you’re leaving your wipers up. What you’re doing isn’t recommended. Read your manual. I’m sure the Maverick Hybrid handles like other FWD cars in the snow. Tires for both FWD and AWD make the difference. More so on the FWD as far as getting started and maintaining forward movement.

• 
  @IllInformedHuman22 күн бұрын

  I assume you are talking about what the manual refers to as the "service position". They say to run the wipers while in accessory mode until they are in the middle of the windshield unless obstructed with snow and ice. For "wiper park" it states that the mode will be active whenever you switch on the side mirror heat. The only precautions for wipers are to leave them off when going through a car wash and to not run them on a dry windshield. It does not state that they cannot be left in the service position. It also does not bring up that you can leave them in service position, thus the debate. I will assume you don't actually own a maverick since you have clearly not READ YOUR MANUAL!

• 
  @myshticaanimo216929 күн бұрын

  If this is cheap than my multimeter is homeless

• 
  @IllInformedHuman27 күн бұрын

  😂

• 
  @myshticaanimo216927 күн бұрын

  @@IllInformedHuman but now it's resistance meter not working after I open it😭

• 
  @IllInformedHuman27 күн бұрын

  @@myshticaanimo2169 It might have never been working!

• 
  @myshticaanimo216927 күн бұрын

  @@IllInformedHuman hum I'm going to buy new one

• 
  @stevenhooten4275Ай бұрын

  Massey for me with his choices jd is a rich man throw away tractor have way too many problems motor wise and too expensive. Kubota is way too cheap and breakdown like crazy for people who use them for how they are made to be used a relative has a kioti and he loves it but doesn't work it like a tractor just once in awhile id prefer a case emax or new holland workmaster 25s

• 
  @paaaoАй бұрын

  For some additional insight here... Everywhere power is generated, or transformed, you need to establish a ground reference. For example, you may have single phase 240Vac coming into your house from the power company. Where the voltage and current are transformed (the transformer on the utility pole for instance), a ground/neutral bond is established to create a reference that is common to both sides. Same thing in commercial control applications where you may take 3 phase 480V and grab one leg of it to a 480:120Vac xfmer. The low side of that transformer will have two wires that read 120Vac between the two. One of them will be bonded directly to ground on that secondary side in order to maintain a common reference to the same ground on the high (480v) side. The ground bonded leg will now be the secondary's ground (green wire) and neutral (white wire). After that point, the two will never join each other again, and if another xformer was added down stream to say, drop 120Vac down to 24Vac, the process would continue. The ground wire to ground, hot and neutral to high side of transformer, then on the low side, two wires will exit, with one wire being bonded to ground to maintain the common earth reference that began all the way back at the turbine that spun up to create the power in the first place. Long ramblings just to explain that if you measure without ground off the secondary side of an inverter that is internally bonded to the negative side of the battery supplying the power, you're not going to get completely accurate results. Thank you for catching this.

• 
  @IllInformedHumanАй бұрын

  Thank you for the info!

• 
  @JamesOcran-mf6tqАй бұрын

  Hi am James from west Africa. I want your contact

• 
  @user-ft3oc7ks9zАй бұрын

  What tractor model?

• 
  @IllInformedHumanАй бұрын

  Kubota MX6000

• 
  @user-hx9tp9cn2hАй бұрын

  Did you consider using a Zip-Lock bag iwth the Oven Cleaner process?

• 
  @IllInformedHumanАй бұрын

  The thought did cross my mind, I did not have a zip lock when I filmed this video 🥲

• 
  @wearethelandrovers9014Ай бұрын

  I have been driving for about 60 years and have lived in places where it gets to MINUS 40 and a foot or more of snow in a single night. I have never even heard of leaving wipers up like you show here. Your method is guaranteed to burn out the wiper motor if you have an inch of ice on the arms with the blades up.

• 
  @qzorn4440Ай бұрын

  A most interesting adventure. 😎 Thank you.

• 
  @IllInformedHumanАй бұрын

  Adventure is a good description, thank you!

• 
  @philwood97602 ай бұрын

  My uncle bought a Ford Tractor in the 70's. He's RIP but the tractor is still going. Another thing to consider is that tractors will last longer than you.(insert disclaimer here) so get what you can get parts for down the road. Kubota engines made in Illinois. They have 2 factories in Georgia.

• 
  @IllInformedHuman2 ай бұрын

  Excellent point!

• 
  @inkylumine89672 ай бұрын

  I'm confused why you have to be condescending against the chinese language and the country itself 😕 im from hong kong so i hate china but its not very nice to be racist

• 
  @michaelchyles2 ай бұрын

  oh hell yes keep it up

• 
  @IllInformedHuman2 ай бұрын

  I am pretty sure I have no choice at this point!

• 
  @spinesales3 ай бұрын

  Nice job. Can you share measurements?

• 
  @IllInformedHuman3 ай бұрын

  I just posted an image of the stand with the dimensions on my "Community" tab. Please reference that for more detail. Key dimensions are: 26" wide, 66" tall with the bottom of the bracket being 4" from the top of the footing.

• 
  @andrewbutlin85023 ай бұрын

  Great breakdown. Thank you.

• 
  @IllInformedHuman3 ай бұрын

  Glad the video was was of use!

• 
  @hawaiivolcanosquad33223 ай бұрын

  The important thing to know is electronic equipment can be damaged or destroyed or even explode if connected to that SHAPE of power wave. There is a story of an audio equipment repair technician friend of mine called to service an expensive studio mix board that was being modified by the studio owner. Tech asked studio owner; "Before you power it up, are you sure you know what you are doing?' Owner said "Yes". Tech: "Okay, its your board sir." Owner powers up his mix board then all 96 channels of his $million dollar SSL mix board blow up in sequence, one at a time, smoke rising over each channel one at a time. Next, tech was hired to fix it (after it stopped smoking). He made a lot of $ off that guy.

• 
  @IllInformedHuman3 ай бұрын

  Definitely! Expensive stuff should have filtering, even with a reliable mains supply. Though... In your example, it sounds like there was more going wrong than just dirty power. Thanks for sharing!

• 
  @user-nf2pi8fr9k3 ай бұрын

  Do you think with a 12v Milwaukee battery Does it posible to use paint sprayer

• 
  @IllInformedHuman3 ай бұрын

  The device in the video needs an 18V battery. For the 12V battery, they only have something that gives you USB power.

• 
  @gbltheolechurch5acrehomestead3 ай бұрын

  🚜👷🏻‍♂️👨‍🌾⚠️🇨🇦Removed my snowblower yesterday and reinstalled the backhoe!

• 
  @IllInformedHuman3 ай бұрын

  I love my backhoe! That thing is the only reason we kept the sub compact around after buying a bigger tractor!

• 
  @gbltheolechurch5acrehomestead3 ай бұрын

  I wonder can those augers be rented? I need to install lots and lots of fence posts.

• 
  @IllInformedHuman3 ай бұрын

  I have seen them around my local stores. You might have something near you as well. The thing comes in handy, you probably wouldn't be upset if you bought one.

• 
  @ethanstorey34853 ай бұрын

  Cartridges are extremely over priced for heat shrink tubing $80 a cartridge?!?!?! That’s ridiculous!!!

• 
  @IllInformedHuman3 ай бұрын

  They are not priced competitively, that is for sure!

• 
  @oxynnyxo27633 ай бұрын

  Is there a way to edit data that are saved into database or to send wrong data?

• 
  @IllInformedHuman3 ай бұрын

  You can edit what is on your card using this method. You wouldn't be able to effect the database that references the card.

• 
  @oxynnyxo27632 ай бұрын

  @@IllInformedHuman Can we make a clone card that sends data for entry and exit in a same time for example and to make 8hours difference in between entry and exit. ?

• 
  @IllInformedHuman2 ай бұрын

  @@oxynnyxo2763 It sounds like you want to change something on the Database side of the card reader. Most card reading systems only record when the card was swiped by a reader and which reader. Forcing the reader to change what time it read a card is not possible from the reader itself. You would need database access to alter that.

• 
  @user-pu7mc7pk8s3 ай бұрын

  please one video for cloning 125khz card also

• 
  @user-ve3yg9vw5j3 ай бұрын

  The easiest way to keep snow out of the windshield wiper valley is use a windshield cover it covers the opening and keeps the valley clean no worries of it getting filled with snow and you do not need to raise the wipers I have not had any problem with snow here in Ontario Canada

• 
  @IllInformedHuman3 ай бұрын

  Interesting concept, I have not hear of that. I will have to check it out!

• 
  @binnad70913 ай бұрын

  Citristrip, my dude. It's less caustic, fast, and easy. Stripped the lacquer off my rusted typewriter in no time!

• 
  @IllInformedHuman3 ай бұрын

  Thanks for the tip!

• 
  @michaelchyles3 ай бұрын

  I WANT TO SEE MORE!

• 
  @IllInformedHuman3 ай бұрын

  ☺ There might be something in the works.

• 
  @MrExlege3 ай бұрын

  How is the concrete ballast weight working out? Is 1,300 the right amount? Seems like most people only get to 800-1000 lbs with concrete. I will be getting an MX soon and thought 800 probably was not enough.

• 
  @IllInformedHuman3 ай бұрын

  It is still holding up! I did put concrete sealer a few months after it was cast. Since the rear can lift over a ton, I would say the right amount would have been just below that 😉. Though... a bigger weight probably would be annoying to drive around with. The size of the one I made feels just right. I usually only have to hook up the weight when I am unloading off a flatbed. I was able to pick up a 1,500lb plow to about half height. I still felt a little light in the rear... so if you could get more weight without it being unwieldy, go for it! if you are planning on moving large round bales, 800lbs would likely be fine. To be safe, fill the tires or add wheel weights as well. Happy tractoring!

• 
  @irvingfelker53843 ай бұрын

  The wiper issue is user error not the vehicle

• 
  @IllInformedHuman3 ай бұрын

  Falling off a staircase without a railing is user error, that doesn't mean the staircase should remain without railings.

• 
  @t0fast3 ай бұрын

  I clicked on this vid cause I wanted to see how it would fare New England winters and you made that clear by trying to back up a 2 degree hill with less than an inch of snow and not being able to w/o having to do something the make it work. I would love the hybrid, but we have 6 months of winter here and it just wouldn't make sense, unfortunately.

• 
  @IllInformedHuman3 ай бұрын

  That was the worst snow storm we had here this year. Sorry bud. Not every solution works for everybody.

• 
  @clubhouseacademy3 ай бұрын

  best setting for just regular labeling- office

• 
  @IllInformedHuman3 ай бұрын

  My recommendation would be Horizontal text

• 
  @user-vp5vf3er3n4 ай бұрын

  Can you still use your old one, (the one you coppied)?? Or only the new one? I hope you can still answer!!

• 
  @IllInformedHuman4 ай бұрын

  You can use either the original or the new copied badge as long as they only reference the block 0 or UID. If they add anything else to any other block each time you swipe, you can only use one of the cards that were copied.

• 
  @Luaramuffin4 ай бұрын

  As an electrician's apprentice you just saved my hide! Thanks!!!

• 
  @IllInformedHuman4 ай бұрын

  Glad to be of help. Enjoy learning your trade!

• 
  @riverdigger24974 ай бұрын

  used one of those for a bit. It worked ok. Never great cuts. Just used an Alaskan mill for the first time amd i wont go back. for 80$ the lumber turned out better and it was much easier to run. Thanks for 411!!

• 
  @IllInformedHuman4 ай бұрын

  And thank you for dropping the name Alaskan Mill, I might have to pick one up!

• 
  @marcovaldovinos50094 ай бұрын

  I use this for soldering and dremel when installing car audio. ❤

• 
  @IllInformedHuman4 ай бұрын

  Excellent uses!

• 
  @secpac58chichi4 ай бұрын

  LOL - the Ford CE-NotKnow lives in Miami and could careless about cold weather and the RealWorld as that is why they spent $15B on the EV's that they have now abandoned - can you imagine being a low level manager and doing that - you would have been fired day two - shout out to the Ford "C" Suite and the moron board of directors - its good to be rich and stupid

• 
  @uphunter55555 ай бұрын

  It would be nice to see the video in real time, the sped up video gives me a headache

• 
  @randylloyd99475 ай бұрын

  I went with the Massey GC1725M. Does everything I need to do. Haven't had any problems. Bought it New,with bucket and backhoe, Great price.

• 
  @IllInformedHuman5 ай бұрын

  Awesome, glad you found something that suits you perfectly!

• 
  @markweese27205 ай бұрын

  Hey brother... please don't let any of your wiring lay against the metal of your container. Drill holes in all of your studs and pull it through them. Looking good! BTW, the way you wedged your ceiling framing to the upper container wall with the studs underneath makes your walls way stronger than you realize. Good job. I'm going to use 2x6 for my ceiling so I can install insulation and some sort of board material above.

• 
  @IllInformedHuman5 ай бұрын

  Its a little late for rewiring 😘 If you want ceiling insulation, consider putting something on top of the container (an insulated party deck?), the interior is only 7'8". Dropping it as much as I did with the 2x4s was almost a little too much... Leaving it open at least makes it feel bigger in there. If you bought a high cube container, you would have plenty of head room! I wish you well on your build!

• 
  @vb98215 ай бұрын

  No idea what you said or what im looking at but ive used the top off to charge everything from m12 batteries for my heated jacket to my phone and laptop. All i want to know is if i can use the top off with my coffee pot. Guess i could plug it in and try but im scared.

• 
  @IllInformedHuman5 ай бұрын

  No you cannot, the smallest drip coffee maker needs ~500watts. This thing can only produce 175W :(

• 
  @jaekoletzky50455 ай бұрын

  My Kubota M7060 tractor started this past Saturday in South Dakota with overnight lows down to -24F. I glow plugged it 3 times and it started. The tractor was parked outside and not plugged in either. Blew me away!

• 
  @IllInformedHuman5 ай бұрын

  Thinking on why my MX starts so much better than my BX, I think it has to do with the placement of the fuel tank. The MX has it right above the engine while the BX has it by the operator! I'd be curious to see how well a grand L performs, since they have the tank below the engine 🤔

• 
  @FLEMZZY5 ай бұрын

  Great choice on best tractors Kubota never lets u down 👍👍

• 
  @IllInformedHuman5 ай бұрын

  Ah, I see you are a man of culture as well! Yep, the Kubota has yet to let me down!

• 
  @ivanestrada34685 ай бұрын

  I still don't know what "presize"means

• 
  @IllInformedHuman5 ай бұрын

  It sounds like some sort of "condition" you wouldn't want!

• 
  @jamesmaccari91285 ай бұрын

  My new Maverick is doing awesome here in the Pennsylvania hills. Of course my CMax was great in the snow too but the Maverick with the extra ground clearance is the bomb.

• 
  @IllInformedHuman5 ай бұрын

  I have also been appreciative of the ground clearance :)

• 
  @brianmccarthy13225 ай бұрын

  Ironic that the site is called ILL-INFORMED HUMAN!! Diesels HATE cold weather. Battery warmers and block heaters help. Diesel can turn syrupy in cold too. Too many failed starts works wonders for the engine oil too!

• 
  @IllInformedHuman5 ай бұрын

  Hopeful this was informational, since it sounds like you wouldn't dare attempt a cold start yourself!

• 
  @vduval525 ай бұрын

  Unprofessional and unprepared. Gross.

• 
  @IllInformedHuman5 ай бұрын

  sorry?

• 
  @user-pp4ve6qo1b5 ай бұрын

  Unwatchable.

• 
  @IllInformedHuman5 ай бұрын

  Thanks for the view!

• 
  @thndr_54685 ай бұрын

  If that is your biggest problem then it must be a pretty good vehiche!

• 
  @IllInformedHuman5 ай бұрын

  Oh yea, You would have to offer 5X sticker for me to even consider trading it in!

• 
  @barney19415 ай бұрын

  do you have a block heater? $55 kats usa made. easy install dont buy any add ons from dealer. amazon any questions just ask

• 
  @IllInformedHuman5 ай бұрын

  I don't have a block heater, I have been able to start it up is -10F weather with no issues.