Bro in my flame sensor don't have ao pin so how I do run my project please give me a perfect code and circuit diagram for ao pin for I run my project perfectly please
@saadinnovativeideas4 минут бұрын
Brother AO is not needed to connect for this project. Mine one was having an extra and that goes alone. Connect them all according to circuit diagram for sensor shown in video at duration 03:21 . Check out
@haziqizzuddin4377Күн бұрын
how to use relay module instead of using transistor
@saadinnovativeideas10 минут бұрын
With same circuit diagram
@andrijastojkovic88152 күн бұрын
Is ut posible to use Submersible pump 2.5-6VDC Instead of the one you used?
@saadinnovativeideas2 күн бұрын
Of course you can use that
@ashadalmahmud16553 күн бұрын
How much valu zener diode needed?
@saadinnovativeideas3 күн бұрын
1N4148 silicon switching signal diode
@I.M.Genius3 күн бұрын
which wire is used to connect flame sensor please tell I want to make this
@saadinnovativeideas3 күн бұрын
Jumper wire.. I did not got what you actually mean
@I.M.Genius3 күн бұрын
@@saadinnovativeideas Sir I want to know which type of wire is used to connect flame sensors with Arduino is it jumper wire or other if other then tell the name please
@saadinnovativeideas3 күн бұрын
I have used jumper wire but I have trimmed its one end to solder it. You can do the same or otherwise use male to female jumper wire but then your breadboard connection will be little bit more complex
@I.M.Genius2 күн бұрын
@@saadinnovativeideas The trimmed jumper wire is male to female ?
@saadinnovativeideas2 күн бұрын
Whichever, but when you trim you should select the one having one side male and the other side is to be soldered
@theoldknowledge67783 күн бұрын
Oh... I thought it was a flame thrower robot
@saadinnovativeideas3 күн бұрын
No it is anti-flame thrower
@elight_editz014 күн бұрын
Mashallah I am very happy to see your project
@saadinnovativeideas4 күн бұрын
Jazakalah❤️
@hermanasmartinez18074 күн бұрын
Did you use battery charging for your batteries?
@saadinnovativeideas4 күн бұрын
Yeah li-ion Rechargeable cell
@hermanasmartinez18074 күн бұрын
Everything works except the wheel motors, the problem would be the battery
@saadinnovativeideas4 күн бұрын
Which battery have you used and how much is the total output voltage
@NicedayNice-wp1bp4 күн бұрын
Thank you for replying fast. But in the video u said 102 pf And in comments 104 uf. Which should i buy. And thank you again
@saadinnovativeideas4 күн бұрын
Always welcome brother. As I tell you before an average limit, you can use 104 if you avail that. But if you did not got that you can do parallel connections of small valued capacitors to reach the desired value.
@NicedayNice-wp1bp5 күн бұрын
Great work. Can I use 100 uf instead of 104 uf ?
@saadinnovativeideas5 күн бұрын
Yes of course. You can use from 90 upto 110 uf and a little round about that
@aminuabdulrazaqozovehe2825 күн бұрын
This is a good idea...Brilliant i must say
@saadinnovativeideas5 күн бұрын
So nice of you brother. Glad you like it
@rupamabasumatary52005 күн бұрын
Kitne range taq sense karega ?
@saadinnovativeideas5 күн бұрын
1-1.2 meters tak
@user-iu1lc5dx3z5 күн бұрын
very inspiring. can you make a video on how to use the every pin of the arduino uno OR ESP32 board, i mean explaination of the pins what's their pupose which pin can serve which task either transmissionm recieving , direction control or input supply ? I have the board unable to reconize their pins which pin i can use for which pupose. can you make a video on that ? i have searched on google a sheet appear but that is also a fixed notions .
@saadinnovativeideas5 күн бұрын
Thats interesting brother Arduino uno board have multiple pin including; digital pins, analog pins, power pins and some other like RESET and AREF… but this require vast explanation and require a video… but brother I am a student of intermediate (FSC) and I am having final exams currently so I apologise, I could not make such video now. I will work upon it when exams comes over
@Funwithsciencetechnyks6 күн бұрын
bro can u explain me why u used a transistor
@saadinnovativeideas6 күн бұрын
As I haven’t used relay module for driving water pump. So TIP transistor is used to regulate current and voltage to the pump so it could not be damaged
@marcelocartagena8347 күн бұрын
I bought the same materials but when I connect the 5V cable to the arduino, it does not turn on. What could be the problem?
@saadinnovativeideas7 күн бұрын
When you connect connect *Arduino uno* with laptop/Computer through arduino cable it should turn with red led blinking
@BhavaniVlogs828 күн бұрын
Bro please tell how to connect water pump with external capacitor and transistor
@saadinnovativeideas8 күн бұрын
Connect them according to circuit diagram. Use jumper wires and breadboard *or* solder it
@teo_net29delvalle688 күн бұрын
Súper!!!
@nishanthreddy50368 күн бұрын
Bro code not working please help me out
@saadinnovativeideas8 күн бұрын
Have you selected right *port* and *board* . Text me the error
@nishanthreddy50367 күн бұрын
For me its showing only 1 port COM3
@nishanthreddy50367 күн бұрын
In the robot flame are working but servo and tyres are not moving
@saadinnovativeideas7 күн бұрын
Select *com* in tool-serial port which ever is showing
@saadinnovativeideas7 күн бұрын
How much voltage and amps have you given to the motor driver, I mean which battery have you used
@opmido13318 күн бұрын
HELLO SAAD I HAVE PROBLEM IN YOUR CODE BEFORE FIRE DETETCTION THE RELAY WORK BEFORE DETETCTING FIRE AND WHEN FIRE IS DETETCTED THE RELAY NOT WORKING AND PUMP IS OFF
@saadinnovativeideas8 күн бұрын
Which circuit diagram and code have you followed?
@opmido13316 күн бұрын
I Didn't use your circuit in youre relay i have a mini pompe 5 v branched with 5 v relay but i changed youre code to have the servo work with pump but the motors work in the beginning until the flamme is detected they stop i think maybe they need a High voltage and last question how much they need in ampetage and voltage 4 dc motors
@saadinnovativeideas6 күн бұрын
No brother that would not require more voltage. The problem could be the incompatibleness of circuit diagram and code. So cannot guess your circuit diagram. Recorrect the code according yo circuit diagram
@opmido13315 күн бұрын
@@saadinnovativeideas now its working I discover that the sensor detectie the light of window i still have the problem in the direction of the motor
@saadinnovativeideas5 күн бұрын
Yeah brother it has a little drawback that the sensor detects light rays, so could be disturbed in the open light
@opmido13318 күн бұрын
hello my freind good job i want ask you a favor could you add a obstacle avoiding in the same servo please i couldnt make it im new in arduino projects and god bless you
@saadinnovativeideas8 күн бұрын
Thanks brother.. Yeah you can add ultrasonic sensor but the circuit diagram as well as code will differ by little modification. I am gonna make fire fighter with obstacle avoidance, I will upload the video
@DevineniHarika9 күн бұрын
Hi , The given code is it correct or do we need to make any changes on it ? getting below error on uploading the code Sketch uses 3368 bytes (10%) of program storage space. Maximum is 32256 bytes. Global variables use 196 bytes (9%) of dynamic memory, leaving 1852 bytes for local variables. Maximum is 2048 bytes. avrdude: ser_open(): can't open device "\\.\COM6": The semaphore timeout period has expired. Failed uploading: uploading error: exit status 1
@saadinnovativeideas9 күн бұрын
Yeah the code is correct. If you follow the circuit diagram as it is I provided so don’t do any changes. In case of changes in circuit diagram, modify code accordingly with that one
@DevineniHarika9 күн бұрын
We need help to setup the diagram, if possible we can connect for 5 min
@saadinnovativeideas8 күн бұрын
Brother the text you have sent for error is not the error in code. Error is in the uploading procees; you have not selected the right *PORT* Download *driver* to connect port
@saadinnovativeideas8 күн бұрын
I did not got, what you want to connect for 5 minnutes?
@DevineniHarika8 күн бұрын
5 min to show our project photo,so that you can check weather we built it correctly or not
@user-jd8oy4vs9s9 күн бұрын
Please send the code by text message
@saadinnovativeideas9 күн бұрын
Can you access it by the link provided in the video description.. if not then let me known
@kaptuinabel407210 күн бұрын
So in short no smoking anymore?
@surjeetyadav252412 күн бұрын
Sir why you dont use relay module
@saadinnovativeideas11 күн бұрын
Because I was not having that... you can use relay module
@surjeetyadav252412 күн бұрын
Kon kon si library install krni pdegi please help
@saadinnovativeideas11 күн бұрын
Bhi me ne full set of code ka description me de dia hai download karda.. koi additional library ki zarorat nahi hai
@Hacer-yk6ce13 күн бұрын
😂😂😂çok güzel olmuş
@saadinnovativeideas13 күн бұрын
🤗
@JenDabhi13 күн бұрын
Good work bro.❤️ But my flame sensor is not working
@saadinnovativeideas13 күн бұрын
Thanks… Make sure have connected them well according with circuit diagram.. if flame sensor’s red led are not turning on then change connections if there are turning on and still not work with project then let me know
@dianaapriatin337814 күн бұрын
Why does mine make a continuous sound when it hits the light and when it hits the light it doesn't make a sound, that's why, si
@saadinnovativeideas14 күн бұрын
When light strikes LDR the buzzer doesn’t make sound, when light is interrupted (by an object supposed to be theif) it should sound, because Light Dependent Resister provide resistance when ther is light…
@emersonoliveira636414 күн бұрын
Sensacional 👏🏽👏🏽👏🏽👏🏽👏🏽👏🏽
@saadinnovativeideas14 күн бұрын
Thanks brother 😊
@Jbideas525214 күн бұрын
There was 3port on my flame sensor😢
@saadinnovativeideas14 күн бұрын
Then thats more easy to connect. Mine one has an extra pin DO for this project.
@ManjuKumari-lh4fx17 күн бұрын
Does it require any bluetooth or wifi connection or it can run independently onto to extinguish the fire?
@saadinnovativeideas17 күн бұрын
No brother it has auto control. It has flame sensors that detects fire and Arduino interprets the signal and perform task as programmed. It doesn’t required any kind of transmitter
@abod_saif.98717 күн бұрын
Hi saad, I have question in the circuit diagram it says that for the flame sensor connect the G to ground, but in Ur video you connected the DO not the G, why? because we did the same project everything worked except the left side two motors I don’t know why ?
@saadinnovativeideas17 күн бұрын
Do connections according to circuit diagram. Connect *ground* with *G*. I had changed it after, behind the scenes.
@abod_saif.98716 күн бұрын
thank you for responding, Also, in the code it says that enA goes to pin 10 but U put it in pin ~5, U flipped all the enA with enB should I do the same U did or I do As the code says ? Because as I told you the left side wheels doesn’t move at all !
@saadinnovativeideas16 күн бұрын
Brother it doesn’t matters much. If you flip the anA with enB the motors(wheels) will rotate in the opposite direction of desired, it doesn’t mean that they wont rotate. I flipped but then I flipped the motor wires as well. You just do all connections according to circuit diagram I provided.
@VishalVlogs199218 күн бұрын
All good but wheel not rotate.. please solution
@saadinnovativeideas17 күн бұрын
MAKE SURE; your you have connected 7-12 V to *12V* and *GND* pin of Motor Driver, you have removed pin connectors from *ena* & *enb* pins. Compare connections with circuit diagram and check the code
@elecfreaks18 күн бұрын
Hello, I would like to contact you for cooperation😄
@bilashimahato258318 күн бұрын
Code missing in description box
@saadinnovativeideas18 күн бұрын
Sorry, Check it now
@rekhadk210518 күн бұрын
Can u send synopsis and circuit diagram plz
@saadinnovativeideas18 күн бұрын
You can download Circuit Diagram by clicking the link provided in the description..
@rekhadk210518 күн бұрын
Bro how can I do this same project in low budget...
@saadinnovativeideas18 күн бұрын
Use cheap components.. use the local cheap water pump, remove wheels from a toy…
@rnlgaming75619 күн бұрын
You deserve more brother thank you❤
@saadinnovativeideas18 күн бұрын
🤗 😊 ❤️
@phinpheen754119 күн бұрын
Well done ✅
@saadinnovativeideas19 күн бұрын
❤️
@Frozensam270319 күн бұрын
Will u please provide the code ?
@saadinnovativeideas19 күн бұрын
Check it in the description
@bilashimahato258318 күн бұрын
@@saadinnovativeideas?...
@saadinnovativeideas18 күн бұрын
Check it now
@Frozensam270318 күн бұрын
@@saadinnovativeideas thank you 😊
@VishalVlogs199218 күн бұрын
Tq sir
@user-xk8bi1op5s19 күн бұрын
hi bro, I also do videos on Arduinos I have excellent knowledge of Arduino programming please don't hesitate to ask me if you need assistance
@saadinnovativeideas19 күн бұрын
So nice of you brother. Yeah I will not hesitate to ask you
@harishakmharishakm396119 күн бұрын
How much cost for this project
@saadinnovativeideas19 күн бұрын
About, PKR 8500 = 30$ for the components
@dimiodufote401019 күн бұрын
I noticed you did a Daisy chaining methods for motor. Can you do a parallel connection how to do that. I am trying to connect two head of the 🤖 robot. Using Arduino chips. I have subscribed aswell.
@saadinnovativeideas19 күн бұрын
Both the BO motor pairs are connected in parallel. What type of function you are going to perform with robots using arduino?
@dimiodufote401019 күн бұрын
@@saadinnovativeideas I don't know yet, but I will find answers soon 🔜
@jeh052020 күн бұрын
Mashallah brother so cool
@saadinnovativeideas20 күн бұрын
Jazakallah brother ❤️
@anil099320 күн бұрын
Bro i need make this project can u plz help me
@saadinnovativeideas20 күн бұрын
Sure, how can I help you
@jeh052020 күн бұрын
I hope your wishes come true because you are really a genius
@saadinnovativeideas20 күн бұрын
So nice of you 😊
@jeh052020 күн бұрын
Hi my friend,, can you told me how can i learn in effective why? I have the baisc but i never do robot because I just student
@saadinnovativeideas20 күн бұрын
Yeah you can just learn these all because of your interest and curiosity. Try to make something like this, start with easy one, and never give up if you fail..
Пікірлер
Bro in my flame sensor don't have ao pin so how I do run my project please give me a perfect code and circuit diagram for ao pin for I run my project perfectly please
Brother AO is not needed to connect for this project. Mine one was having an extra and that goes alone. Connect them all according to circuit diagram for sensor shown in video at duration 03:21 . Check out
how to use relay module instead of using transistor
With same circuit diagram
Is ut posible to use Submersible pump 2.5-6VDC Instead of the one you used?
Of course you can use that
How much valu zener diode needed?
1N4148 silicon switching signal diode
which wire is used to connect flame sensor please tell I want to make this
Jumper wire.. I did not got what you actually mean
@@saadinnovativeideas Sir I want to know which type of wire is used to connect flame sensors with Arduino is it jumper wire or other if other then tell the name please
I have used jumper wire but I have trimmed its one end to solder it. You can do the same or otherwise use male to female jumper wire but then your breadboard connection will be little bit more complex
@@saadinnovativeideas The trimmed jumper wire is male to female ?
Whichever, but when you trim you should select the one having one side male and the other side is to be soldered
Oh... I thought it was a flame thrower robot
No it is anti-flame thrower
Mashallah I am very happy to see your project
Jazakalah❤️
Did you use battery charging for your batteries?
Yeah li-ion Rechargeable cell
Everything works except the wheel motors, the problem would be the battery
Which battery have you used and how much is the total output voltage
Thank you for replying fast. But in the video u said 102 pf And in comments 104 uf. Which should i buy. And thank you again
Always welcome brother. As I tell you before an average limit, you can use 104 if you avail that. But if you did not got that you can do parallel connections of small valued capacitors to reach the desired value.
Great work. Can I use 100 uf instead of 104 uf ?
Yes of course. You can use from 90 upto 110 uf and a little round about that
This is a good idea...Brilliant i must say
So nice of you brother. Glad you like it
Kitne range taq sense karega ?
1-1.2 meters tak
very inspiring. can you make a video on how to use the every pin of the arduino uno OR ESP32 board, i mean explaination of the pins what's their pupose which pin can serve which task either transmissionm recieving , direction control or input supply ? I have the board unable to reconize their pins which pin i can use for which pupose. can you make a video on that ? i have searched on google a sheet appear but that is also a fixed notions .
Thats interesting brother Arduino uno board have multiple pin including; digital pins, analog pins, power pins and some other like RESET and AREF… but this require vast explanation and require a video… but brother I am a student of intermediate (FSC) and I am having final exams currently so I apologise, I could not make such video now. I will work upon it when exams comes over
bro can u explain me why u used a transistor
As I haven’t used relay module for driving water pump. So TIP transistor is used to regulate current and voltage to the pump so it could not be damaged
I bought the same materials but when I connect the 5V cable to the arduino, it does not turn on. What could be the problem?
When you connect connect *Arduino uno* with laptop/Computer through arduino cable it should turn with red led blinking
Bro please tell how to connect water pump with external capacitor and transistor
Connect them according to circuit diagram. Use jumper wires and breadboard *or* solder it
Súper!!!
Bro code not working please help me out
Have you selected right *port* and *board* . Text me the error
For me its showing only 1 port COM3
In the robot flame are working but servo and tyres are not moving
Select *com* in tool-serial port which ever is showing
How much voltage and amps have you given to the motor driver, I mean which battery have you used
HELLO SAAD I HAVE PROBLEM IN YOUR CODE BEFORE FIRE DETETCTION THE RELAY WORK BEFORE DETETCTING FIRE AND WHEN FIRE IS DETETCTED THE RELAY NOT WORKING AND PUMP IS OFF
Which circuit diagram and code have you followed?
I Didn't use your circuit in youre relay i have a mini pompe 5 v branched with 5 v relay but i changed youre code to have the servo work with pump but the motors work in the beginning until the flamme is detected they stop i think maybe they need a High voltage and last question how much they need in ampetage and voltage 4 dc motors
No brother that would not require more voltage. The problem could be the incompatibleness of circuit diagram and code. So cannot guess your circuit diagram. Recorrect the code according yo circuit diagram
@@saadinnovativeideas now its working I discover that the sensor detectie the light of window i still have the problem in the direction of the motor
Yeah brother it has a little drawback that the sensor detects light rays, so could be disturbed in the open light
hello my freind good job i want ask you a favor could you add a obstacle avoiding in the same servo please i couldnt make it im new in arduino projects and god bless you
Thanks brother.. Yeah you can add ultrasonic sensor but the circuit diagram as well as code will differ by little modification. I am gonna make fire fighter with obstacle avoidance, I will upload the video
Hi , The given code is it correct or do we need to make any changes on it ? getting below error on uploading the code Sketch uses 3368 bytes (10%) of program storage space. Maximum is 32256 bytes. Global variables use 196 bytes (9%) of dynamic memory, leaving 1852 bytes for local variables. Maximum is 2048 bytes. avrdude: ser_open(): can't open device "\\.\COM6": The semaphore timeout period has expired. Failed uploading: uploading error: exit status 1
Yeah the code is correct. If you follow the circuit diagram as it is I provided so don’t do any changes. In case of changes in circuit diagram, modify code accordingly with that one
We need help to setup the diagram, if possible we can connect for 5 min
Brother the text you have sent for error is not the error in code. Error is in the uploading procees; you have not selected the right *PORT* Download *driver* to connect port
I did not got, what you want to connect for 5 minnutes?
5 min to show our project photo,so that you can check weather we built it correctly or not
Please send the code by text message
Can you access it by the link provided in the video description.. if not then let me known
So in short no smoking anymore?
Sir why you dont use relay module
Because I was not having that... you can use relay module
Kon kon si library install krni pdegi please help
Bhi me ne full set of code ka description me de dia hai download karda.. koi additional library ki zarorat nahi hai
😂😂😂çok güzel olmuş
🤗
Good work bro.❤️ But my flame sensor is not working
Thanks… Make sure have connected them well according with circuit diagram.. if flame sensor’s red led are not turning on then change connections if there are turning on and still not work with project then let me know
Why does mine make a continuous sound when it hits the light and when it hits the light it doesn't make a sound, that's why, si
When light strikes LDR the buzzer doesn’t make sound, when light is interrupted (by an object supposed to be theif) it should sound, because Light Dependent Resister provide resistance when ther is light…
Sensacional 👏🏽👏🏽👏🏽👏🏽👏🏽👏🏽
Thanks brother 😊
There was 3port on my flame sensor😢
Then thats more easy to connect. Mine one has an extra pin DO for this project.
Does it require any bluetooth or wifi connection or it can run independently onto to extinguish the fire?
No brother it has auto control. It has flame sensors that detects fire and Arduino interprets the signal and perform task as programmed. It doesn’t required any kind of transmitter
Hi saad, I have question in the circuit diagram it says that for the flame sensor connect the G to ground, but in Ur video you connected the DO not the G, why? because we did the same project everything worked except the left side two motors I don’t know why ?
Do connections according to circuit diagram. Connect *ground* with *G*. I had changed it after, behind the scenes.
thank you for responding, Also, in the code it says that enA goes to pin 10 but U put it in pin ~5, U flipped all the enA with enB should I do the same U did or I do As the code says ? Because as I told you the left side wheels doesn’t move at all !
Brother it doesn’t matters much. If you flip the anA with enB the motors(wheels) will rotate in the opposite direction of desired, it doesn’t mean that they wont rotate. I flipped but then I flipped the motor wires as well. You just do all connections according to circuit diagram I provided.
All good but wheel not rotate.. please solution
MAKE SURE; your you have connected 7-12 V to *12V* and *GND* pin of Motor Driver, you have removed pin connectors from *ena* & *enb* pins. Compare connections with circuit diagram and check the code
Hello, I would like to contact you for cooperation😄
Code missing in description box
Sorry, Check it now
Can u send synopsis and circuit diagram plz
You can download Circuit Diagram by clicking the link provided in the description..
Bro how can I do this same project in low budget...
Use cheap components.. use the local cheap water pump, remove wheels from a toy…
You deserve more brother thank you❤
🤗 😊 ❤️
Well done ✅
❤️
Will u please provide the code ?
Check it in the description
@@saadinnovativeideas?...
Check it now
@@saadinnovativeideas thank you 😊
Tq sir
hi bro, I also do videos on Arduinos I have excellent knowledge of Arduino programming please don't hesitate to ask me if you need assistance
So nice of you brother. Yeah I will not hesitate to ask you
How much cost for this project
About, PKR 8500 = 30$ for the components
I noticed you did a Daisy chaining methods for motor. Can you do a parallel connection how to do that. I am trying to connect two head of the 🤖 robot. Using Arduino chips. I have subscribed aswell.
Both the BO motor pairs are connected in parallel. What type of function you are going to perform with robots using arduino?
@@saadinnovativeideas I don't know yet, but I will find answers soon 🔜
Mashallah brother so cool
Jazakallah brother ❤️
Bro i need make this project can u plz help me
Sure, how can I help you
I hope your wishes come true because you are really a genius
So nice of you 😊
Hi my friend,, can you told me how can i learn in effective why? I have the baisc but i never do robot because I just student
Yeah you can just learn these all because of your interest and curiosity. Try to make something like this, start with easy one, and never give up if you fail..
I need some help...can you help me💙
Sure, why not. Tell me how can I help you
Keep going❤
Thanks bro ❤️
Salam brother my name is also Saad
Wassalam brother. How are you my namesake