How much volt LED lamp does it support, I want to upgrade mine from Aliexpress with 16k lumens LED Lamp 18V
@garymartin69872 күн бұрын
You DID verify that the IC was properly oriented, right?
@dark1stuКүн бұрын
yes as long as the markings on the board are correct , this happens with the cheep kits now and agen
@johnrudd95503 күн бұрын
Should have used solder paste….
@dark1stuКүн бұрын
most hobbyist builders dont have solder paste , so whilst i could have used it this was about showing you can do it without ,
@pokepress3 күн бұрын
I've been using one of these to generate audio for my AM radio AI upscale project. The fact that the range is so short is actually somewhat helpful for testing different kinds/degrees of interference.
@dark1stu3 күн бұрын
It's a very crude, but kind of cool little transmitter , I've just got an FM kid, I'm gonna build in the next few weeks
@inglepropnoosegarm78018 күн бұрын
Roberts, along with Hacker and Grundig, were regarded as the finest portable radios back then, so not surprising that it sounds so good. Obviously built to last too. Unlike anything you can buy now.
@dark1stu3 күн бұрын
i agree some of the old kit works better than the new miniaturised junk
@JamesE70710 күн бұрын
1971! Thanks.
@JamesE70710 күн бұрын
No FM? FM came about in the early to mid 1960s, so is this earlier?
@JamesE70710 күн бұрын
Looks old, circa late 1960s? I haven't looked on the web BTW.
@UrbanoDagrippino13 күн бұрын
I fixed a Hitachi wh 888 r
@dark1stu11 күн бұрын
thats cool its good to keep the hertige alive
@andrewbevan466214 күн бұрын
Why the constant background music ?
@dark1stu13 күн бұрын
at the time of recording this i was on a farm an its to drown out the background noise , newer video's dont have the backing as i have found software to remove / reduce the background noise , as a few comments have mentioned it
@florinlupascu181621 күн бұрын
Hi. Main it’s come lights for 10 seconds and turn of. No chime. Can be de cpu issue? Thanks
@dark1stu18 күн бұрын
im not sure this was just my experience fixing mine
@Waltprov21 күн бұрын
Hi! I was wondering if the fan was pulling air into the projector, or if it was blowing air out. I have an identical model and I had to take it apart to repair, but now I'm not sure which way the fan is supposed to go back in. Any help would be great. Thanks.
@dark1stu11 күн бұрын
I have no idea its been a good while since striping this
@Waltprov5 күн бұрын
@@dark1stu ah well, thanks anyway.
@weinbergfahrer404822 күн бұрын
Thanks for this video, that shouldn't be too difficult! (fingers crossed. :)) But... what was the problem with Sonoma?
@dark1stu22 күн бұрын
its sill geting mayor updates and that can brick OCLP . as mine is used for work i have gone with the safe option , but it douse run and it runs well
@forrest60324 күн бұрын
I had this SAME problem. I tried to explain it's a durability issue, too, but B&O basically told me to F off and gave access to discount, refurbished equipment. I am not likely to buy from them again.
@dark1stu23 күн бұрын
its a bit of a issue , the socket is clearly not strong enough to be continuously used socket is not held on by a lot
@forrest60323 күн бұрын
My argument to them is that it was NOT designed to be a travel speaker, that this was an obvious flaw. Someone is going to drop it. That's what happens when you travel, so it kindof exposes a lack of foresight of the designers. They could care less, of course.
@user-rn6ln5hk6m25 күн бұрын
Kindly asking where i can purchase the dash din
@dark1stu24 күн бұрын
i got mine off ebay
@catharperfect703627 күн бұрын
Pretty lame, even most Chinese stuff is better built.
@dark1stu27 күн бұрын
Yes the Iron is awesome but they have some build issues , and if they have used inslated crimps or heat shrink over them is would me much safer
@alancarr631428 күн бұрын
I have one of these with win7 , it's a fast machine with SSD. Problem is no drivers for win10 / 11. Are you planning to put another os onto yours ?
@dark1stu28 күн бұрын
We use this on Xp at work for programing old kit i have had win 10 on i it did sort it self out but it did not run the best
@dark1stu28 күн бұрын
Hi all Just a quick note the damage on the bottom and back happened when it hit the deck after electrocuting me , ask because infantry flailing on my arm .
@GordonFalt29 күн бұрын
This video saved my life. I’ve had the vac since 2017 or 2018, use it all the time. But at the jobsite I’m currently at, the home owners have two German shepards and I’ve been sanding oak stair treads. So wicked fine dust and dog hair. Vac wasn’t happy. Took apart and stuck a coat hanger down each tine. Purrs like a kitten now.
@dark1stu28 күн бұрын
Im glad it helps it was not a bad teardown
@lukejones2772Ай бұрын
Alright Stu, nice job mate. Took me a minute to recognise the voice 😅
@dark1stuАй бұрын
yep . its not a bad tool
@duckmyassАй бұрын
Nice video... I'm trying to stick Windows on one... any idea which drivers are the newest yet stable? Using the boot camp version seems to work, but they are very old... but the latest AMD drivers caused constant crashing... I know there are several version in between Apple's last bootcamp version and the last AMD... but it would be nice to know which one to use. I've already wasted hours restoring it 2 different times after killing it with various newer drivers.
@Thecubemaster10Ай бұрын
Handy video. I couldnt remember what way round the wires for the thermostat went. Thank you
@dark1stu27 күн бұрын
glad it helped
@karunyapadsunaart5191Ай бұрын
What
@dark1stu28 күн бұрын
joke right , total junk
@dark1stu28 күн бұрын
ebay uk
@akidim13Ай бұрын
Where you get the speaker adapters
@dark1stu28 күн бұрын
ebay uk
@bryanbornholdt8068Ай бұрын
I just bought one of these, it hasn't even arrived yet. I'm glad to see you like it.
@dark1stu27 күн бұрын
its a good tool
@keithgribble8143Ай бұрын
Cheers bud my makita works great now awesome
@dark1stu27 күн бұрын
Glad to hear it
@TheAppleLabАй бұрын
nice one...but what caused the issue in the end? my 6,1 never turn on after a run. got pretty hot but behaves normaly...after a forced switch off, it never came back alive. diassembled everything, gave it a good clean and repaste gpu's and cpu...going to try with the coin cell next.
@dark1stu11 күн бұрын
i cant remember , but it kept working till i sold it to get. a imac
@fgg591Ай бұрын
Thanks! I was able to fix mine! 🎉
@dark1stu27 күн бұрын
Glad it helped
@patty10862 ай бұрын
dreamer
@JamesE7072 ай бұрын
Nice work, and good video - no silly wavering the camera about. A few things I noticed ... It's weight, by the way you had to drag it around. I was surprised that it had speakers from the side panels. And, no tape lifter? Yikes, more tape head wear? All that said, a classic. Thanks for the uploading of this video!
@dark1stu27 күн бұрын
Ye i used a Fixed camera its much easier on the Eyes
@alannorris58032 ай бұрын
very good , help me greatly. will use you again thank you
@dark1stu11 күн бұрын
Glad to hear that
@ColonelMuppet2 ай бұрын
I am still not sure if you replaced the power supply, or whether it was the paste/old resin problem that ultimately stopped it powering up?
@dark1stu11 күн бұрын
yes i changed the psu out , but i think the other one was ok
@zbynekba2 ай бұрын
You have loaded the tape incorrectly. Check the path leading to the right reel.
@dark1stu2 ай бұрын
possibly but it worked so it cant be that wrong
@andrewdupuis11513 ай бұрын
i have Sony reel to reel it still works good
@dark1stu11 күн бұрын
cool , not played with a sony yet
@seanallen9243 ай бұрын
Have 2 of the these radios that didn’t work, fixed both of them now because of your vid. Also found a corroded line in the circuit board that stopped it powering on so joined that with a bit of wire. Thank you very much!!
@dark1stu11 күн бұрын
Glad I could help
@WinrichNaujoks3 ай бұрын
great video, but doesn't need any background music
@dark1stu11 күн бұрын
in the envoroment i was in it was needed , newer vidios dont have backing as a rule
@RockwellAIM653 ай бұрын
I wish Weller would get its act together. Am about ready to give up and go Hakko coz I've got not one but two dead old Wellers! Unacceptable situation.
@dark1stu11 күн бұрын
i no , its a concerning trend
@mawin58994 ай бұрын
What was actually wrong with it causing the failure to power up?
@ColonelMuppet2 ай бұрын
Exactly! Did he replace the power supply or not? I don’t even have any lights around ports lighting up anymore after an initial strip down and clean
@paulhipp2 ай бұрын
Colonel Muppet.. I had the same situation. Stripped it down, cleaned it, nothing. No lights nothing. Replaced the power supply ($50). Now I have the lights back but it’s still not booting. Debating whether to try new logic board or if that would just be a further waste of doe. Anyway, just an FYI for you. Good luck.
@dahlia6954 ай бұрын
Thanks for the video. I just got one, came with 64GB, a 12 core cpu, and a700 gpus. It has a 1 TB WD green drive in it that had Monteray installed. I put a drive in it that had Windows 11 that I took out of another computer and it booted right up and loaded all the proper dirvers as soon as it updated. I notice occassional graphics studder when playing games and it makes me wonder if it's getting hot somewhere but I took the top fan off and it all looks very clean inside, but maybe it needs new paste or something. I want to watch a few more videos before I try to repaste it. Your video is the best one I've seen so far.
@scott73052 ай бұрын
It might not be possible - but try allocating more ram for your games!
@andreweh45 ай бұрын
My God man...Please get a mount for your camera. I am motion sick trying to watch this.
@jonihenry81245 ай бұрын
Thanks for showing how to fix these lights! I have the exact fan/light that doesn't work and wasn't sure how to fix it. Now, I do!! 🙂
@followthebeat665 ай бұрын
This wiring! Maaaan. It's like someone cooked spaghetti in there.
@marceldaalen66046 ай бұрын
Update May 28/2024. Bad take-up reel. Cleaned the friction from bottom side , a white nylon part with a spring. Works fine now. Yet owner of a TC-K1A , TC-K2A, TC-K4, TC-K5, TC-K6 and very soon an TC-229SD. Former text : Bought a few months ago the same Sony TC 121. Still working. I'm collecting all the audio devices my dad and I bought in the '60 >'80. Fixed lately a Sony TC-K5. Own 2 TC-K6. Also own Fisher, Graetz and Pioneer. Great to see this video. Update Jan 28, 2024. Own a second 2nd hand TC 121. At playback the tape is gonna drift to the outside. Take-up reel has torque enough, pinchroller is a little bit rounded. No high freq at playback. Maybe audiohead must be adjusted again. Someone srewed this wonderful cassetterecorder :(
@NicholaiB6 ай бұрын
Thank you so much for the video. I was stumped by the polarity of the LEDs, but not any more 🙂
@dark1stu11 күн бұрын
its not always clear
@vasstagoarchipelagus59546 ай бұрын
You should use antistatic table, and gloves etc.
@alanturnell73716 ай бұрын
You need to thread it on the front of the pin to the right of the record/playback head so it lifts the tape off the heeds during FF & RW to avoid the high speed playback noise & excessive head wear.
@steveaustin89376 ай бұрын
I don't know why people insist on putting music in the background when they are talking, it is so distracting.
@hiresindonesia6 ай бұрын
What size is the rubber?
@dark1stu2 ай бұрын
I don't know I just bought it off eBay
@funnybunny86 ай бұрын
any idea how to bring bluetooth back to life ?
@funnybunny86 ай бұрын
Bluetooth Not working After Installing This.... otherwise its running very smooth on my mac pro 5,1
Пікірлер
How much volt LED lamp does it support, I want to upgrade mine from Aliexpress with 16k lumens LED Lamp 18V
You DID verify that the IC was properly oriented, right?
yes as long as the markings on the board are correct , this happens with the cheep kits now and agen
Should have used solder paste….
most hobbyist builders dont have solder paste , so whilst i could have used it this was about showing you can do it without ,
I've been using one of these to generate audio for my AM radio AI upscale project. The fact that the range is so short is actually somewhat helpful for testing different kinds/degrees of interference.
It's a very crude, but kind of cool little transmitter , I've just got an FM kid, I'm gonna build in the next few weeks
Roberts, along with Hacker and Grundig, were regarded as the finest portable radios back then, so not surprising that it sounds so good. Obviously built to last too. Unlike anything you can buy now.
i agree some of the old kit works better than the new miniaturised junk
1971! Thanks.
No FM? FM came about in the early to mid 1960s, so is this earlier?
Looks old, circa late 1960s? I haven't looked on the web BTW.
I fixed a Hitachi wh 888 r
thats cool its good to keep the hertige alive
Why the constant background music ?
at the time of recording this i was on a farm an its to drown out the background noise , newer video's dont have the backing as i have found software to remove / reduce the background noise , as a few comments have mentioned it
Hi. Main it’s come lights for 10 seconds and turn of. No chime. Can be de cpu issue? Thanks
im not sure this was just my experience fixing mine
Hi! I was wondering if the fan was pulling air into the projector, or if it was blowing air out. I have an identical model and I had to take it apart to repair, but now I'm not sure which way the fan is supposed to go back in. Any help would be great. Thanks.
I have no idea its been a good while since striping this
@@dark1stu ah well, thanks anyway.
Thanks for this video, that shouldn't be too difficult! (fingers crossed. :)) But... what was the problem with Sonoma?
its sill geting mayor updates and that can brick OCLP . as mine is used for work i have gone with the safe option , but it douse run and it runs well
I had this SAME problem. I tried to explain it's a durability issue, too, but B&O basically told me to F off and gave access to discount, refurbished equipment. I am not likely to buy from them again.
its a bit of a issue , the socket is clearly not strong enough to be continuously used socket is not held on by a lot
My argument to them is that it was NOT designed to be a travel speaker, that this was an obvious flaw. Someone is going to drop it. That's what happens when you travel, so it kindof exposes a lack of foresight of the designers. They could care less, of course.
Kindly asking where i can purchase the dash din
i got mine off ebay
Pretty lame, even most Chinese stuff is better built.
Yes the Iron is awesome but they have some build issues , and if they have used inslated crimps or heat shrink over them is would me much safer
I have one of these with win7 , it's a fast machine with SSD. Problem is no drivers for win10 / 11. Are you planning to put another os onto yours ?
We use this on Xp at work for programing old kit i have had win 10 on i it did sort it self out but it did not run the best
Hi all Just a quick note the damage on the bottom and back happened when it hit the deck after electrocuting me , ask because infantry flailing on my arm .
This video saved my life. I’ve had the vac since 2017 or 2018, use it all the time. But at the jobsite I’m currently at, the home owners have two German shepards and I’ve been sanding oak stair treads. So wicked fine dust and dog hair. Vac wasn’t happy. Took apart and stuck a coat hanger down each tine. Purrs like a kitten now.
Im glad it helps it was not a bad teardown
Alright Stu, nice job mate. Took me a minute to recognise the voice 😅
yep . its not a bad tool
Nice video... I'm trying to stick Windows on one... any idea which drivers are the newest yet stable? Using the boot camp version seems to work, but they are very old... but the latest AMD drivers caused constant crashing... I know there are several version in between Apple's last bootcamp version and the last AMD... but it would be nice to know which one to use. I've already wasted hours restoring it 2 different times after killing it with various newer drivers.
Handy video. I couldnt remember what way round the wires for the thermostat went. Thank you
glad it helped
What
joke right , total junk
ebay uk
Where you get the speaker adapters
ebay uk
I just bought one of these, it hasn't even arrived yet. I'm glad to see you like it.
its a good tool
Cheers bud my makita works great now awesome
Glad to hear it
nice one...but what caused the issue in the end? my 6,1 never turn on after a run. got pretty hot but behaves normaly...after a forced switch off, it never came back alive. diassembled everything, gave it a good clean and repaste gpu's and cpu...going to try with the coin cell next.
i cant remember , but it kept working till i sold it to get. a imac
Thanks! I was able to fix mine! 🎉
Glad it helped
dreamer
Nice work, and good video - no silly wavering the camera about. A few things I noticed ... It's weight, by the way you had to drag it around. I was surprised that it had speakers from the side panels. And, no tape lifter? Yikes, more tape head wear? All that said, a classic. Thanks for the uploading of this video!
Ye i used a Fixed camera its much easier on the Eyes
very good , help me greatly. will use you again thank you
Glad to hear that
I am still not sure if you replaced the power supply, or whether it was the paste/old resin problem that ultimately stopped it powering up?
yes i changed the psu out , but i think the other one was ok
You have loaded the tape incorrectly. Check the path leading to the right reel.
possibly but it worked so it cant be that wrong
i have Sony reel to reel it still works good
cool , not played with a sony yet
Have 2 of the these radios that didn’t work, fixed both of them now because of your vid. Also found a corroded line in the circuit board that stopped it powering on so joined that with a bit of wire. Thank you very much!!
Glad I could help
great video, but doesn't need any background music
in the envoroment i was in it was needed , newer vidios dont have backing as a rule
I wish Weller would get its act together. Am about ready to give up and go Hakko coz I've got not one but two dead old Wellers! Unacceptable situation.
i no , its a concerning trend
What was actually wrong with it causing the failure to power up?
Exactly! Did he replace the power supply or not? I don’t even have any lights around ports lighting up anymore after an initial strip down and clean
Colonel Muppet.. I had the same situation. Stripped it down, cleaned it, nothing. No lights nothing. Replaced the power supply ($50). Now I have the lights back but it’s still not booting. Debating whether to try new logic board or if that would just be a further waste of doe. Anyway, just an FYI for you. Good luck.
Thanks for the video. I just got one, came with 64GB, a 12 core cpu, and a700 gpus. It has a 1 TB WD green drive in it that had Monteray installed. I put a drive in it that had Windows 11 that I took out of another computer and it booted right up and loaded all the proper dirvers as soon as it updated. I notice occassional graphics studder when playing games and it makes me wonder if it's getting hot somewhere but I took the top fan off and it all looks very clean inside, but maybe it needs new paste or something. I want to watch a few more videos before I try to repaste it. Your video is the best one I've seen so far.
It might not be possible - but try allocating more ram for your games!
My God man...Please get a mount for your camera. I am motion sick trying to watch this.
Thanks for showing how to fix these lights! I have the exact fan/light that doesn't work and wasn't sure how to fix it. Now, I do!! 🙂
This wiring! Maaaan. It's like someone cooked spaghetti in there.
Update May 28/2024. Bad take-up reel. Cleaned the friction from bottom side , a white nylon part with a spring. Works fine now. Yet owner of a TC-K1A , TC-K2A, TC-K4, TC-K5, TC-K6 and very soon an TC-229SD. Former text : Bought a few months ago the same Sony TC 121. Still working. I'm collecting all the audio devices my dad and I bought in the '60 >'80. Fixed lately a Sony TC-K5. Own 2 TC-K6. Also own Fisher, Graetz and Pioneer. Great to see this video. Update Jan 28, 2024. Own a second 2nd hand TC 121. At playback the tape is gonna drift to the outside. Take-up reel has torque enough, pinchroller is a little bit rounded. No high freq at playback. Maybe audiohead must be adjusted again. Someone srewed this wonderful cassetterecorder :(
Thank you so much for the video. I was stumped by the polarity of the LEDs, but not any more 🙂
its not always clear
You should use antistatic table, and gloves etc.
You need to thread it on the front of the pin to the right of the record/playback head so it lifts the tape off the heeds during FF & RW to avoid the high speed playback noise & excessive head wear.
I don't know why people insist on putting music in the background when they are talking, it is so distracting.
What size is the rubber?
I don't know I just bought it off eBay
any idea how to bring bluetooth back to life ?
Bluetooth Not working After Installing This.... otherwise its running very smooth on my mac pro 5,1