Пікірлер

• 
  @cougrr684 күн бұрын

  Which sikaflex adhesive is it

• 
  @peterhoward55264 күн бұрын

  Very helpful

• 
  @johnmorley14197 күн бұрын

  Oh my!! you butchered that, please don't follow this as a guide, this is NOT how you use the multitool.

• 
  @theidealprojectmanager814613 күн бұрын

  Thanks for showing

• 
  @BlackFoxProduc19 күн бұрын

  Duct tape it while it cures

• 
  @outaboutwithmarkjustine318319 күн бұрын

  why all the fkn music

• 
  @MINTY_ROGUE_YT25 күн бұрын

  The black little bar goes on the top of the slat frame on the headboard side

• 
  @MINTY_ROGUE_YT25 күн бұрын

  Your wrong on the black corner holders because it has to be the other way because the slat frame comes down that little bit further but the way you have put it make the slat frame sit up just that little bit extra and when your laying down on it it can damage the gas arms

• 
  @MINTY_ROGUE_YT25 күн бұрын

  Your wrong on the black corner holders because it has to be the other way because the slat frame comes down that little bit further but the way you have put it make the slat frame sit up just that little bit extra and when your laying down on it it can damage the gas arms

• 
  @MINTY_ROGUE_YT25 күн бұрын

  Omg you built it in the slowest and longest and worst way possible

• 
  @lolly_kitty_cat336025 күн бұрын

  Are you able to assist as to why my mower wont go any faster than a crawl. I have the same with the lever you just push for speed but the control will only move an inch or so. same in reverse

• 
  @johannelanglois3126Ай бұрын

  You block the view multi time with your hand, so I can’t see how you take the thing on the top of the battery. Thank you

• 
  @stepnegАй бұрын

  Wow it actually works! I was about to order a new machine but just thought I would check KZread first, thanks so much.

• 
  @agwomlАй бұрын

  Our machine has a leakage somewhere (F70 i think), we got rid of that but a few drops of water managed to leak into the relai. We took it apart and dried it but that didn't do the trick, so we're waiting till tomorrow. Hope it works. Thank you for the video👍

• 
  @Hahehhwgajshah72726..Ай бұрын

  Looks like a TiTan shed you have there.My shed is the same.Good video.I have that much crap in mine.

• 
  @user-be6db3ih8zАй бұрын

  Набора фрез всегда говно и для чего та металлическая маленькая пластина?

• 
  @atuane7003Ай бұрын

  Especially wirh hardwood its advisable to protect your lungs as well

• 
  @michaelaugier6294Ай бұрын

  Gonna try undoing the feet on one side and slide the pod with the far u bolts loosely done up then put the near feet of the rack back the put the near u bolts on

• 
  @bendemartinis51422 ай бұрын

  How to connect door waterline

• 
  @willa02732232 ай бұрын

  Great reviews Shaun. Love your video!

• 
  @bigsonslawncare2 ай бұрын

  Love it!

• 
  @Susan-L1932 ай бұрын

  Excellent information.! Thanks for sharing 😊

• 
  @ctruong1832 ай бұрын

  Hi , Did it fix the dripping with the new tap seat? Cheers, Chris.

• 
  @countrylifeonthecoast41672 ай бұрын

  Yes it fixed it. I had to replace the black washer after 6 months or so, but it's still working great.

• 
  @oldgamer13302 ай бұрын

  That is not how you setup to sharpen drill bits.

• 
  @bookofrevelation49242 ай бұрын

  Could two strings with weight on both ends be used by laying the strings across the top of post and line up post so that all 4 weights hanging on sides of post are resting equally along side of post? Longer the string, easier to see gaps between weights and side of post?

• 
  @garyharty31082 ай бұрын

  bought the machine and had nothing but problems with the hose connection into the gun and the gun connection causing water to go everywhere even when using plumbing tape to seal the leak- dont but it as parts are not easy to replace

• 
  @sadimsean18362 ай бұрын

  Why did you sharpen your knife in that angle?

• 
  @emeraldlhasaapsos522 ай бұрын

  The rectangular bar is to go at the top of the bed frame to stop the mattress slipping forward when gas lift is up. There are holes for it at top of metal bed frame. 😅

• 
  @hansignals95932 ай бұрын

  My timer cracked at the top but I can now replace the whole thing thanks to your video.

• 
  @hansignals95932 ай бұрын

  Alas, Pope don’t support the product any longer, so they couldn’t replace the broken part. Planned obsolescence.🙁

• 
  @bristolfashion44213 ай бұрын

  Nice one, chap... 😊

• 
  @SuperCharlesPeter3 ай бұрын

  you need to screw the base to a bench

• 
  @mariapropst79353 ай бұрын

  What an incredible car show! Enjoyed watching! Thank you!!!

• 
  @ONIS-RD3 ай бұрын

  Muchas gracias por esta gran ayuda.👍

• 
  @ScottTheNews3 ай бұрын

  Thank you so much mate. I just ordered this kit

• 
  @nimalsamaraweera95013 ай бұрын

  Thanks for the great video! Just what I was looking for as the surfacing tool I bought could not fix the crack just like in your case.

• 
  @davidsturtz17313 ай бұрын

  can you tell me what the little yellow push button by the throttle lever does . i dont have a book on the tractor i just got last week thanks

• 
  @countrylifeonthecoast41673 ай бұрын

  It's a safety button that you need to depress when you use the mower in reverse. With the blades engaged, if you try to reverse without pushing the button, the engine will cut out. If yours works without needing to push the button, then someone has disconnected the switch. Hope that helps.

• 
  @patrickwright20313 ай бұрын

  you think a patch would bond fron the inside of a deck if properly prepared, and can you send a link to the sika product, Cheers!

• 
  @timothytremblay77633 ай бұрын

  Good job mate✌️😎

• 
  @felicitywade55573 ай бұрын

  Thank you Sean for sharing your video. I fixed my fridge because you cared to share. Cost was $63.83 for the defrost element. Time probably 2.25 hours. It was not at all fun to fix it though. At times I just wanted to give up. I am hoping to get another 13 years out of this last Australian made fridge. Thanks again and God bless.

• 
  @countrylifeonthecoast41673 ай бұрын

  Great job fixing your fridge. Glad the video helped

• 
  @papuas53 ай бұрын

  Спасибо друг, помог!!!

• 
  @PomFrit-tl1xv3 ай бұрын

  Top vid Sean - tomorrow's Saturday morning job for me. Already got local Meile page open on the replacement relay part, if I need to order a new one. Some interesting previous replies in respect of turn it off for 24hrs or tap the relay...interesting to see if that works, or whether its delaying the inevitable replacement of the relay. All The Best, G

• 
  @countrylifeonthecoast41673 ай бұрын

  Hope it went well! The relays are normally what needs to be replaced or repaired. Turning it off for a short period of time can work but in my experience, not for very long.

• 
  @tomorrowsTomorrowАй бұрын

  @@countrylifeonthecoast4167 Have to say Miele dishwasher is rubbish tbh - relay switch problem for my third / fourth time now Anyone recommend a better make - thanks

• 
  @aussieangryparrot51293 ай бұрын

  That metal bar goes on the head side center..but i think it is to hold mattress in place

• 
  @countrylifeonthecoast41673 ай бұрын

  Thanks for the information.

• 
  @Flame_Beard3 ай бұрын

  Hows she treating you two years on?

• 
  @countrylifeonthecoast41673 ай бұрын

  Still works well. To be fair I only use it at times for diy projects, not all the time.

• 
  @TheShortbiker3 ай бұрын

  THANK YOU, this is so helpful. There were a few bits in the box that I couldn't figure out the purpose of - you demonstrated beautifully! There is small rectangular metal plate - you pushed it aside at the start (2'43")... looks like it is meant to go between the black plastic base plate and the metal base plate - looks to me like it would just make it much harder to change the bit. Have you fitted it since making this video? Any idea why Ryobi would want you to fit that (or not have it fitted out of the box?) Their manual is a bit useless.

• 
  @Franna6953 ай бұрын

  Hi guys. I’ve never ever seen a ridge capping cut to fit the shape of the sheets. Geeez it must have been the worst part of the build. Good job. 👍

• 
  @countrylifeonthecoast41673 ай бұрын

  Thanks. It wasn't fun, but it is what is done all the time around here.

• 
  @nicofish31004 ай бұрын

  Go to Jacar get your own relays .and make up a new board ......BETTER THAN THIS MIELE CRAP!!!!

• 
  @countrylifeonthecoast41673 ай бұрын

  Thanks for the comment. I agree replacing the relays would be a great way to do it. Can you advise what model relays to get from Jaycar to help others?

• 
  @johnmoseley51114 ай бұрын

  I like that. Here in Arkansas we call it rustic. Is Queensland arid? Very humid here. I just rebuild some of my wood fence. Which gets gets blown down regularly from Thunderstorms. So I have the slats, treated pine. I am opening my pool now and had to replace the top of the valve assembly. It became brittle. believe the damage I get to my pool filter comes from the direct sun exposure. So with that in mind. Humidity will make it moldy. It really think it just needs shade. I think I will add 1/2 in. (About 13mm) wood spacers between the overlaps on the side slats to allow plenty of air flow. And I believe I have enough dog eared top pieces to make a rustic looking wooden shingle roof also. My only expense will be red barn paint (to match all the other things i have in the back yard) and screws. Thanks for the ideas.

• 
  @countrylifeonthecoast41673 ай бұрын

  It can be humid here at times too. I find if I can keep air flow around it, then there is no mould. There hasn't been any mould around it so far and it's been there quite a while now.

• 
  @elementbeneteau17354 ай бұрын

  Do you know if the head unit fits onto the older screw together pole, rather than the telescopic pole. I have the older pole and don't want to end up with 2 poles. I called Ryobi help desk in Australia which seems to be run in India and they couldn't answer the question.

• 
  @NobodyHereCares4 ай бұрын

  Terrible. Get to the point

• 
  @ylleskog4 ай бұрын

  Thank you for this informational video. Saved my machine which I thought were an impossible case to fix. 🙏🏻