Пікірлер

• 
  @noahw95494 күн бұрын

  Love jboats. Nice job saving it!

• 
  @conqueringlion4209 күн бұрын

  Ehh

• 
  @Ol_Maude2 ай бұрын

  Did you have trouble with the 90 degree corners and the liner?

• 
  @tonyrobinson90463 ай бұрын

  Thanks.

• 
  3 ай бұрын

  It's been a few years, how's it holding up?

• 
  @Vienneau3 ай бұрын

  it was all good untill i decided I wanted to move it. it was starting to backen my siding.

• 
  @backin3 ай бұрын

  Are you using polyester resin or epoxy?

• 
  @Vienneau3 ай бұрын

  epoxy

• 
  @InfinityPoolDIY4 ай бұрын

  Nice. check my step by step diy construction videos. Im building infinity pool without skimmer

• 
  @michaelplates5 ай бұрын

  Great job man and very informative

• 
  @Vienneau5 ай бұрын

  thanks

• 
  @grahammiller58126 ай бұрын

  when you used a sand bottom how did you set up your main drain s?

• 
  @grahammiller58126 ай бұрын

  good video

• 
  @marc-otremblay36849 ай бұрын

  Are you from Québec?

• 
  @Vienneau9 ай бұрын

  new brunswick

• 
  @ewantheboat9 ай бұрын

  Why not skin fhe floorboard with light glass and clear epoxy resin to produce a very strong, hardwearing and pretty floorboard ?

• 
  @Vienneau9 ай бұрын

  THAT IS WHAT I DID AFTER

• 
  @michellechumiecki371310 ай бұрын

  Hi! We just bought a J24 and are restoring it as well! We have a few questions about the process and were wondering if we could connect to ask these questions. Our J24 is a ‘78! Please let me know :) thanks!!

• 
  @Vienneau9 ай бұрын

  Congrats, reach out to me at [email protected]

• 
  @joelzwicker398110 ай бұрын

  Water going in our pool today!! Thank you for the video, the advise & the belief I could do it myself!!

• 
  @Vienneau10 ай бұрын

  Cool

• 
  @user-mw2ky8qq7g11 ай бұрын

  It’s been over 2 years, does it leak?

• 
  @Vienneau11 ай бұрын

  No Leaks still great.

• 
  @ronsedge4906 Жыл бұрын

  Where did you get the plastic templates from? They would be great for making more than one board.

• 
  @Vienneau11 ай бұрын

  i printed the templates on paper then glud them to a sheet of lexan and cut out the templates. easy.

• 
  @nlg062701 Жыл бұрын

  How long did the process take from beginning to end?

• 
  @Vienneau Жыл бұрын

  2-3 months

• 
  @nlg062701 Жыл бұрын

  @@Vienneau was this off and on work? Daily? One man? Crew?

• 
  @Vienneau Жыл бұрын

  @@nlg062701 off and on one man crew except for pouring of walls

• 
  @bend8590 Жыл бұрын

  Great job. Just finishing my ICF pool. We sell the product but i never knew how good they are for pools till i checked into and did my own. Time and money saver!

• 
  @nroose Жыл бұрын

  How many layers of fiberglass did you do in the area where you had to replace the balsa core?

• 
  @Vienneau Жыл бұрын

  4 or 5

• 
  @nroose Жыл бұрын

  Nice shop!

• 
  @Vienneau Жыл бұрын

  Thanks!

• 
  @robertcasey7312 Жыл бұрын

  Thank you. Sincerely appreciate your efforts creating this resource.

• 
  @Vienneau Жыл бұрын

  Thanks for watching.

• 
  @trey1531 Жыл бұрын

  Cool Project! I'm currently working on a J/24 for the past couple years. I'm hoping to launch this summer.

• 
  @Vienneau Жыл бұрын

  cool hope to race ya one day !

• 
  @thaddeuslindsay5872 Жыл бұрын

  When you meet the top face of glass and the bottom face of glass, is there a noticeable bump or anything?

• 
  @Vienneau Жыл бұрын

  no you can hardly tell

• 
  @petervanschaack8361 Жыл бұрын

  Question for you, I looked at one today that have been sitting out and getting wet through the mast step hole. How much damage do you think that may have done? It's in Connecticut so wet and frozen at times. is the keel section of the hull balsa core as well?

• 
  @Vienneau Жыл бұрын

  difficult to say... get a small hammer and lightly tap to find hard or soft spots.

• 
  @user-cd7lj2le4l Жыл бұрын

  Сколько весит ваш board?

• 
  @Vienneau Жыл бұрын

  48 lbs

• 
  @peterjansen1687 Жыл бұрын

  Love it! I’m just starting my own build. How much does your finished board weigh?

• 
  @Vienneau Жыл бұрын

  40 ish pounds

• 
  @andymastercarpenter2380 Жыл бұрын

  Nice job

• 
  @Vienneau Жыл бұрын

  Thanks

• 
  @koreydoutaz6449 Жыл бұрын

  How’s muffin doing? How thick is the balsa core? I need to do the same job

• 
  @Vienneau Жыл бұрын

  Muffin is doing great no issues balsa was about 3/8 if I remember correctly.

• 
  @loafandjug321 Жыл бұрын

  It's odd that you've used wood footer forms instead of ICF footer forms when the pool walls have ICF blocks.

• 
  @Vienneau Жыл бұрын

  it was just a cost thing. thanks for watching

• 
  @ralphstrong3117 Жыл бұрын

  Killer video 👐! Promotion that works = 'Promo sm' .

• 
  @Vienneau Жыл бұрын

  thanks

• 
  @scottdieboldsr.3594 Жыл бұрын

  Th 0:03 thankyou great video. Love the pool

• 
  @Vienneau Жыл бұрын

  thanks

• 
  @scottdieboldsr.3594 Жыл бұрын

  How much did this cost you to build?

• 
  @Vienneau Жыл бұрын

  I did a video on just the cost you can find it on my channel. thanks for watching.

• 
  @manleywilson6535 Жыл бұрын

  Perfect

• 
  @robertmethe859 Жыл бұрын

  How could I contact you about pool liner... I'm in the Moncton area

• 
  @joelzwicker3981 Жыл бұрын

  I asked this question on another one of your videos then I had a part 2 so sorry for the duplicate questions here. I'm in the process of building an ICF pool with Nudera right now in NS. Loved the coping idea going to use it. 2 questions. 1. For the return jets did you simply pour with a 1/ 1/2 PVC pipe through the forms & attach the heads after? 2. I noticed you maintained square corners with your coping, was that an issue with the liner as I know they want curved corners typically.

• 
  @Vienneau Жыл бұрын

  For the returns I used sacrificial pieces of PVC. I had no issues with the 90 degree corner. you have to play a little with the liner in the corners to fit properly but once good I never touched it again...Good luck with your project.

• 
  @joelzwicker3981 Жыл бұрын

  @@Vienneau 1 1/2 inch PVC for the returns?

• 
  @joelzwicker3981 Жыл бұрын

  @@Vienneau I'd also like to thank you. I'm doing a 18x36 pool with a deep & shallow end, heated etc. Your video was one of the best I have found & so very helpful!!

• 
  @Vienneau Жыл бұрын

  @@joelzwicker3981 yes

• 
  @Vienneau Жыл бұрын

  @@joelzwicker3981 yes

• 
  @joelzwicker3981 Жыл бұрын

  Question about the jets. Did you simply poor with 1 1/2 PVC through the wall & attach the jets after?

• 
  @alansmollen Жыл бұрын

  Coo story, im looking for one…. Lower the music, just your voice is much better

• 
  @Vienneau Жыл бұрын

  Thanks

• 
  @krispress7824 Жыл бұрын

  I like your repairs. You saved that boat😀

• 
  @Vienneau Жыл бұрын

  Yes and have loved every minute of it... the boat has returned the favor 10x. thanks for watching.

• 
  @psu8782 Жыл бұрын

  Thank you for the clear explanation and demo. Did you look at the Nudura One Series product that is "ideal for pools and anywhere only one side of the foam is needed (according to their website)". Is it better to have insulation on both sides instead of one side? What are you using to cover the pool? I am planning to build an indoor ICF pool and wondering what would be ideal cover for it, to keep the dirt and moisture out of the pool as much as i can.

• 
  @Vienneau Жыл бұрын

  I never worked with one series so not sure how that would work. good luck with your build.

• 
  @jamesriseley4923 Жыл бұрын

  Can you tile the pool or only vinyl is possible with ICF

• 
  @Vienneau Жыл бұрын

  I am sure you could but I would talk to a tile guy first. I am no expert.

• 
  @shawnphibbs4380 Жыл бұрын

  Thank you so much for making and sharing this! About to start my build in Ontario. The fox block engineered drawings I have are calling for a whopping 14” x 66” footing for my clay soil and 8’ deep end. Do you think that’s really necessary?!

• 
  @Vienneau Жыл бұрын

  I dont have much experience with clay soil.

• 
  @cmsense8193 Жыл бұрын

  In the USA there are bunch of permits to get prior a homeowner project such as this.

• 
  @Vienneau Жыл бұрын

  All they were interested in was the enclosure.

• 
  @ricky2g893 Жыл бұрын

  Great video thanks

• 
  @scottwilson8081 Жыл бұрын

  Just finished our icf pool walls. Question- how is the sand floor? We were thinking of putting sand down and then a gorilla pad (like the one they use in above ground pools). Do you think that would work? We were also thinking concrete but wasn’t sure what f the sand moved around too much. Thanks! Great videos

• 
  @Vienneau Жыл бұрын

  You wont have issues with sand and a gorilla pad if you have a well draining soil. having said that....that is basickly what I did. If i was to do it again I would probably put sand then 2inch foam insulation tapping every seem twice then a gorilla pad over top. good luck.

• 
  @JiayinMiranda Жыл бұрын

  why don’t you use spray foam?

• 
  @Vienneau Жыл бұрын

  Foam will only help if my board has a leak....and it doesn't. foam will not make the board more buoyant.

• 
  @jakeademar1233 Жыл бұрын

  What size is your pool?

• 
  @Vienneau Жыл бұрын

  14ftx28ft

• 
  @indiandad Жыл бұрын

  Awesome video! Can you shed a little more light if you removed the coping afterwards? And how did u go about installing liner?

• 
  @Vienneau Жыл бұрын

  If you look at my videos I have an other video explaining just that. let me know if you cannot find it. Thanks

• 
  @williamstrong2068 Жыл бұрын

  Hi, did tout have to work on fixing gel coat cracks everywhere on the hull? Or the only problem you had was around the chain plates? Mine as superficials cracks pretty much every where. And 5 rotten balza soft spots. Did you just covered it all with gel coat and sanded it good bye?

• 
  @williamstrong2068 Жыл бұрын

  After fixing your rotten soft spot*

• 
  @Vienneau Жыл бұрын

  BoatworksToday is a youtube channel that has good information on just that. as for what i did I had very few stress cracks so I fixed the worst ones and didnt even do anything for the little ones. I highly recommend you watching BoatworksToday on you tube.

• 
  @williamstrong2068 Жыл бұрын

  Me again, did you poored kiwi grip or another non skid product right on top of original company gel coat surface?

• 
  @williamstrong2068 Жыл бұрын

  Hi, i am currently on a j24 refit project and i sûre have questions coming, especially about deck finish.

• 
  @Vienneau Жыл бұрын

  Feel free to ask if I have the answer I will be more than happy to help.

• 
  @Ddw2164 Жыл бұрын

  If you are interested in building a Jarvis SUP this is a great series to watch. Much, much better than the Jarvis video. I would also caution a potential buyer that the Jarvis kits do NOT contain an instructional manual and the videos are next to worthless. In addition, Jarvis does not answer email questions or provide any support.

• 
  @Vienneau Жыл бұрын

  Thanks for your kind words.