What does it mean. When we hear this sound? It means , is it working good?🤔🤔
@dryerthackston70886 күн бұрын
Thank you! I had no idea about the plastic cover.
@CarharttSlut6 күн бұрын
I was quoted $300 the fuhh
@Darin777JC7 күн бұрын
Looks like this will be the fix. Will give it a try for the “oldie but a goodie” Honda Pilot!
@ISYETUNKNOWN7 күн бұрын
thanks! simple, clear, NBS instruction.
@myykmikelakers13578 күн бұрын
I just shorted out my whole engine jumping that relay... thanks pal !
@garrykennedy54849 күн бұрын
If this happens, you most likely have a bad connector at the low or high pressure switch on the hard lines of the condenser. I have had this happen 3 times so far. Wiggle those connectors. If it causes the compressor clutch to kick in,,, that's your problem!!!!!!!!!! You can try replacing the relay, but I would bet against it. If it does fix it,,, great, but if it don't, check these connectors. When you pull it off,,, you'll typically see burning marks. They use under rated connectors for these connections and are under a lot of vibrational influences. Good luck and God speed.
@froglobster5 күн бұрын
I never thought of loose connections thanks
@garrykennedy54845 күн бұрын
@@froglobster You should have your 12V at both terminals on each pressure switch. Also check the clutch electromagnet. If you're familiar with a multimeter, you should have close to 0 ohms if you unplug the single wire and measure, on the compressor, between where the plug plugs in and the housing, That and having 100PSI at least but no more than 140lbs at rest of freon pressure at the low side and between 35 and 45lbs. when the compressor is running. Good luck.
@froglobster5 күн бұрын
@@garrykennedy5484 Thanks for the tips
@Theluxurypeople249 күн бұрын
Thanks, I was quoted for labor only $175 plus $40 original toyota parts. it took me about 40 minutes to replace it myself for free.
@shaine2289 күн бұрын
I wish i watched this video first. I watched another video and it was not as detailed and did not show how to remove the bulb. I had a hard time trying to remove the bulb but your video actually shows it.
@Camry-pe6up9 күн бұрын
Thank you for this video.question has this sensor cleaning on fuel consumption?
@ctcummings2110 күн бұрын
Fixed it right up! Thanks!
@user-te7os3ku6d16 күн бұрын
Went from struggling for 25 minutes to watching ur video and doing It in 30 seconds, no exaggeration.
@dariosalasjr61016 күн бұрын
Where did you get the terminals ?
@ricardosom776617 күн бұрын
Let me ask you a question. In my case the clutch and the condenser fan work only if I apply ground from external cable to the main lines that go to them. Is this a relay problem? Unfortunately I can’t upload pics or videos to show you what I’m talking about.
@eaglessj18 күн бұрын
Excellent video! Don’t think I could have done it without it. I like that you got straight to work without a lot of extra talk too. Nice job on the install.
@chrisdehmel21621 күн бұрын
vids like this are why KZread is awesome. thank you so much.
@Butterfly417522 күн бұрын
Thank you so much for this video.
@jefersonalexlopezrojas676224 күн бұрын
All the cars has a/c relay? I have a 2021 Nissan versa and I can’t see any relays only 2 fuses
@bobtakealook642025 күн бұрын
Same pin number on other 4 and 5 pin relays 30 and 87
@mrdrivermechanictv4213Ай бұрын
❤❤❤❤❤
@user-dq8wg8kn4oАй бұрын
Hello Sir what kind of car is it please👌🙏🙌 do you have any electric diagram for Scion XA 006 from the wire goes to compressor toward outside & inside toward off & on swich under the redio please👌🙏🙌 . I do thank you for your response 🇺🇸 USA 🫵🫶 your vidio🙏🎉
@gabrielseaff487Ай бұрын
Excelente video e información. Thank you for sharing.
@jfalk35Ай бұрын
Good job!
@mndg2926Ай бұрын
Link is no longer working, please share the bulb name :)
@automahnticАй бұрын
Just updated it, thanks!
@dingdongdillybeanАй бұрын
So if it clicks on and off with it removed on and off on and off. But doesn’t when installed what does that mean?
@waduritoАй бұрын
Probably a bad relay.
@MECASPORTАй бұрын
Thaaaaaank you !! I have this car for 3 years, I finally managed to connect, thanks to you🤝😌
@eugenedizon48Ай бұрын
Impact Wrench is what I needed 👍🏼 Great video!
@lawrencenelson6618Ай бұрын
Thank you, I was able to change my blades without further blood loss after watching your video.
@ussenterp652 ай бұрын
Dang I think I can do that now
@spartak4602 ай бұрын
brilliant help
@ToddDouglas12 ай бұрын
Thanks so so much! Still rocking this old beast of a car. :). Just ordered both items.
@ailsadempsey9512 ай бұрын
Thank you so much for this!
@garrettcipponeri92103 ай бұрын
Thanks for the video. Couple of questions. Once the truck has been remotely started from the outside of the truck, then i get in, do i then need to place the key into the ignition and turn to "on" position in order to drive? Have you heard of or experienced any problems with seat or steering wheel controls once installed and working? Do you happen to know the max range at which the remote starting kit works? Thanks in advance!
@automahntic3 ай бұрын
Yes, after remote starting the vehicle you must turn the key to "On" position otherwise the engine will shut off once you press the brake pedal. Never had or heard of any issues with the seat or steering controls so far. Hasn't had any other type of errors either. The max range would be whatever your original key fob is set to. So whatever distance you get with that would be the same even after the install. There is no extra antenna in the kit. Thanks for the comment!
@rccbccdvdvdv63673 ай бұрын
Very helpful 👌
@grekodr56983 ай бұрын
When I jump with wire compressor starts working just fine , but once I put back the relay some times it works and most times it doesn’t … I already changed the pressure switches and still have the same issues, don’t know what to do now 😅… any suggestions!!
@spice4lyf7993 ай бұрын
Replace relay ?
@boudrostyle16692 ай бұрын
Relay contact get bad after time, the coil inside can also go bad so all the contact doesnt work
@safamilon3 ай бұрын
Brother can you update product link. Is not working
@automahntic3 ай бұрын
Just updated the links. Thanks for letting me know!
@Lou_Zasil3 ай бұрын
does the engine stay running when you open the drivers door?
@automahntic3 ай бұрын
Yes, it only shuts off if you press the brake pedal without the key in the ignition turned to "ON." Also, after 15 minutes it will turn off by itself.
@leonardmorales7464 ай бұрын
And thanks for the vid... Why do shops charge $600 for this?
@leonardmorales7464 ай бұрын
Should the coils be changed when changing the spark plugs?
@automahntic3 ай бұрын
There's no need to replace them with spark plugs. However if you have the funds it wouldn't hurt to do that as well just to future-proof it especially if it's over 150k
@enriqueolguin86504 ай бұрын
Thank you very much good video
@billydick75664 ай бұрын
You've got dandruff all over your dash dude ?
@lllPlatinumlll4 ай бұрын
This doesn't help locate the wire under the dash.
@jomc10764 ай бұрын
This is the best video of someone working on this car
@shotokankaratedo61554 ай бұрын
Also MG Fuse 7.5A would not allow power to Clutch.
@Holden.Tudiks4 ай бұрын
Excellent just what I was looking for
@davisbrett444 ай бұрын
Man I wish every KZread tutorial was this simple. Thank you so much.
@Starlitauto_5 ай бұрын
Love how you were straight to the point, most of these diy video the guy tells you how he’s feeling that day and what he ate for breakfast smh, good job
@YenCrew5 ай бұрын
Thank you very much brother!
@rameshyadav81865 ай бұрын
Thanks
@LisaBeeWilson5 ай бұрын
Brilliant! Short, sweet, and effective. Thank you!
Пікірлер
What does it mean. When we hear this sound? It means , is it working good?🤔🤔
Thank you! I had no idea about the plastic cover.
I was quoted $300 the fuhh
Looks like this will be the fix. Will give it a try for the “oldie but a goodie” Honda Pilot!
thanks! simple, clear, NBS instruction.
I just shorted out my whole engine jumping that relay... thanks pal !
If this happens, you most likely have a bad connector at the low or high pressure switch on the hard lines of the condenser. I have had this happen 3 times so far. Wiggle those connectors. If it causes the compressor clutch to kick in,,, that's your problem!!!!!!!!!! You can try replacing the relay, but I would bet against it. If it does fix it,,, great, but if it don't, check these connectors. When you pull it off,,, you'll typically see burning marks. They use under rated connectors for these connections and are under a lot of vibrational influences. Good luck and God speed.
I never thought of loose connections thanks
@@froglobster You should have your 12V at both terminals on each pressure switch. Also check the clutch electromagnet. If you're familiar with a multimeter, you should have close to 0 ohms if you unplug the single wire and measure, on the compressor, between where the plug plugs in and the housing, That and having 100PSI at least but no more than 140lbs at rest of freon pressure at the low side and between 35 and 45lbs. when the compressor is running. Good luck.
@@garrykennedy5484 Thanks for the tips
Thanks, I was quoted for labor only $175 plus $40 original toyota parts. it took me about 40 minutes to replace it myself for free.
I wish i watched this video first. I watched another video and it was not as detailed and did not show how to remove the bulb. I had a hard time trying to remove the bulb but your video actually shows it.
Thank you for this video.question has this sensor cleaning on fuel consumption?
Fixed it right up! Thanks!
Went from struggling for 25 minutes to watching ur video and doing It in 30 seconds, no exaggeration.
Where did you get the terminals ?
Let me ask you a question. In my case the clutch and the condenser fan work only if I apply ground from external cable to the main lines that go to them. Is this a relay problem? Unfortunately I can’t upload pics or videos to show you what I’m talking about.
Excellent video! Don’t think I could have done it without it. I like that you got straight to work without a lot of extra talk too. Nice job on the install.
vids like this are why KZread is awesome. thank you so much.
Thank you so much for this video.
All the cars has a/c relay? I have a 2021 Nissan versa and I can’t see any relays only 2 fuses
Same pin number on other 4 and 5 pin relays 30 and 87
❤❤❤❤❤
Hello Sir what kind of car is it please👌🙏🙌 do you have any electric diagram for Scion XA 006 from the wire goes to compressor toward outside & inside toward off & on swich under the redio please👌🙏🙌 . I do thank you for your response 🇺🇸 USA 🫵🫶 your vidio🙏🎉
Excelente video e información. Thank you for sharing.
Good job!
Link is no longer working, please share the bulb name :)
Just updated it, thanks!
So if it clicks on and off with it removed on and off on and off. But doesn’t when installed what does that mean?
Probably a bad relay.
Thaaaaaank you !! I have this car for 3 years, I finally managed to connect, thanks to you🤝😌
Impact Wrench is what I needed 👍🏼 Great video!
Thank you, I was able to change my blades without further blood loss after watching your video.
Dang I think I can do that now
brilliant help
Thanks so so much! Still rocking this old beast of a car. :). Just ordered both items.
Thank you so much for this!
Thanks for the video. Couple of questions. Once the truck has been remotely started from the outside of the truck, then i get in, do i then need to place the key into the ignition and turn to "on" position in order to drive? Have you heard of or experienced any problems with seat or steering wheel controls once installed and working? Do you happen to know the max range at which the remote starting kit works? Thanks in advance!
Yes, after remote starting the vehicle you must turn the key to "On" position otherwise the engine will shut off once you press the brake pedal. Never had or heard of any issues with the seat or steering controls so far. Hasn't had any other type of errors either. The max range would be whatever your original key fob is set to. So whatever distance you get with that would be the same even after the install. There is no extra antenna in the kit. Thanks for the comment!
Very helpful 👌
When I jump with wire compressor starts working just fine , but once I put back the relay some times it works and most times it doesn’t … I already changed the pressure switches and still have the same issues, don’t know what to do now 😅… any suggestions!!
Replace relay ?
Relay contact get bad after time, the coil inside can also go bad so all the contact doesnt work
Brother can you update product link. Is not working
Just updated the links. Thanks for letting me know!
does the engine stay running when you open the drivers door?
Yes, it only shuts off if you press the brake pedal without the key in the ignition turned to "ON." Also, after 15 minutes it will turn off by itself.
And thanks for the vid... Why do shops charge $600 for this?
Should the coils be changed when changing the spark plugs?
There's no need to replace them with spark plugs. However if you have the funds it wouldn't hurt to do that as well just to future-proof it especially if it's over 150k
Thank you very much good video
You've got dandruff all over your dash dude ?
This doesn't help locate the wire under the dash.
This is the best video of someone working on this car
Also MG Fuse 7.5A would not allow power to Clutch.
Excellent just what I was looking for
Man I wish every KZread tutorial was this simple. Thank you so much.
Love how you were straight to the point, most of these diy video the guy tells you how he’s feeling that day and what he ate for breakfast smh, good job
Thank you very much brother!
Thanks
Brilliant! Short, sweet, and effective. Thank you!