Пікірлер

• 
  @MadIIMike8 күн бұрын

  I just ordered 15 of the simple SATA to 6 pin connectors. AFAIK the SATA Connector is rated 4.5 amps (58w) while the 6 pin is rated for 75, touch some GPUs have been known to exceed specs by a massive margin. The use case for me is older GPUs that either go slightly above 75w or just have the extra power connector for potential overclocking ability. Since they require the power connector, they are less sought after than ones just managing without and thus cheaper. As far as Power Supplies go, a lot of Business grade office PCs actually have reasonably good ones in terms of quality, at least in relative terms. I'd always take the chance adding a adapter on a 300w+ FSP 80+ PSU than with a used no name PSU. Next to me is a little Fujitsu with their usual tiny proprietary PSUs from the 3rd/4th gen Intel days. The PSU is rated 250w total or 280w for 20 seconds, but it has 2 12v rails at 15 amps (180w) each and a surge for 17amps (204w) for 20 seconds. If you'd max out the load on a i7 3770 (which you wouldn't pair with the GPUs mentioned below) with a stresstest it might go up to 100w, leaving 150w. 550Ti and 650Ti are rated around 115w peak, maybe 130 ish in Furmark.

• 
  @jarus_yt10 күн бұрын

  THANK YOU!!!!!

• 
  @Stazymandias21 күн бұрын

  If I am supplying a 4070 ti super GPU (285w) with an 8 pin, 6 pin to 8 pin adapter, and the GPU slot, can the sata to 8 pin adapter be a good additional support power supply? 500w PSU in an eGPU chassis.

• 
  @Wizzdome125 күн бұрын

  Hi, I notice this is kind of an old video, but I have run into a problem of my own that brought me in curious as to if I could use something like the adapter you are showing. I was recommended a 2x sata to 8pin for my Dell OptiPlex 9020mt (sadly I only have one open sata cable as I have a bit of network drives installed in this pc.) The graphics card is a GTX 1650 (which I was told would run on my psu as it only takes 75watts) however when i plugged it in and started it up it asked for me to power down and connect power to the card... sigh I keep the pc online all the time I will likely be gaming on it as well as video editing and creating my own animation in the future, but I figure at 75 watts that shouldn't be a problem, I am wondering if you think this might be a good idea until I can afford to upgrade my actual psu. (tight budget right now)

• 
  @videogamemadness1582Ай бұрын

  When I copy and paste my save files of Gran Turismo 3 and Freekstyle into the memory card it says it went through but when I check it by launching pcsx2 without the game's it doesn't show the saved data. I'm also using the 2.0 version of pcsx2 and don't know what I'm doing wrong.

• 
  @highrider9168Ай бұрын

  I used hot glue and a torx bit as the metal finger 😂😂😂 cheap alternative! Take a file and file the glue down for smooth clearance.

• 
  @sergeantcrowАй бұрын

  😀 Thank you....

• 
  @Davidlaid01Ай бұрын

  For Gtx 1050 ti which sata to pin cable is better 6 pin or 8 pin ? My power supply is 450 watts ?

• 
  @abdullahx409Ай бұрын

  Thank you so much 😁

• 
  @anasslados6969Ай бұрын

  Guys my psu just 200 watt and i want to upgrade my pc by buying new gpu that is gtx 1650 super that require 6 pin but unforttunaly my psu doesn't have any external power connector so can i use adapter from sata to 6 pin (The gpu draw 100 watt ) So i should fin with it ?

• 
  @Davidlaid01Ай бұрын

  Buy gigabite 550 watt psu it have inbuilt 6 pin connector cable.

• 
  @anasslados6969Ай бұрын

  @@Davidlaid01 but dude i cant change the psu its a prebuilt pc

• 
  @Davidlaid01Ай бұрын

  @@anasslados6969 same problem with me i have gtx 1050 ti but my psu didnt have 6 pin connector now i have ordered 2×SATA 1×6 connector pin which is good for my card.

• 
  @sayibandsusu5013Ай бұрын

  Hi can I use a sata to pcie 6 pin adapter for this gpu?? I think it will be safe as its only 75w. What do you guys think??

• 
  @peaceifye2 ай бұрын

  I recently ordered a 4060 my pc currently has a 1050 need no pins and doesn’t have PCI-E adapters my 4060 is here and i have no clue how to connect it to my psu(powerSupply) bcs i don’t know where to find a 10 pin connecter or a 8 or 6 pin someone help i have a 650watt psu

• 
  @boogiewoogie8922 ай бұрын

  Hey thanks for all the knowledge however I was wondering if there's a time limit to use these adapters as in for how many hours a day of constant use? I have a 75W GTX 1650 with 6 PIN it draws 47W at 100% load from the 1 SATA to 6 PIN adapter and 25W from the PCI slot, knowing that the GPU wont be at 100% all the time lets say 70%-80% in gaming sessions so for how many hours a day can I use it?

• 
  @ShinLarc2 ай бұрын

  Thanks for this video! Wanted to back up some saves after moving across the world. Glad I still have this precious data.

• 
  @Procommand2 ай бұрын

  would it work with a rx 560 8gb gpu?

• 
  @user-yv7hk7tg2f3 ай бұрын

  NOTICE : YOU NEED TO CALCULATE YOUR GPU TDP CAREFULLY !!! one sata cable can supply 54w, and pcie can supply 75w, so the maximum is 129w, and there are two sata to 6+2 pin converter existed, that one can supply 54+54, include 75w pcie will become 183w For the safe, please only implement this solution when you found your gpu will only use 80% - 90% of the maximum power, one sata ~100w, two sata ~146w

• 
  @user-yv7hk7tg2f3 ай бұрын

  you also can undervolt gpu, this will be more safe

• 
  @caden3ds3 ай бұрын

  Fried my gpu by accidently using this

• 
  @9ja-Alexander3 ай бұрын

  Thanks so much for this video. Really helped. ❤

• 
  @Yassermalik.3 ай бұрын

  Hey, when you give up you second hard drive for the graphics card is your second hard drive still working??

• 
  @Kythe1-kjea4 ай бұрын

  If u want not a bad GPU in it get a gtx 1660 low profile and get a 8 pin to 6+2 adapter

• 
  @HybridCartoon4 ай бұрын

  thank you so much, bro. you literally saved my persona 3 playthrough, god bless you man!!

• 
  @joaogabriel-uf8cm4 ай бұрын

  jesus from ps2, thank you so much :3

• 
  @ItsJayMCZK4 ай бұрын

  Is it good to plug my RX 560?

• 
  @ClaireCJS4 ай бұрын

  My 15-year-old sharport saves don't have a file extension. I have no idea how to recover them into PCSX2

• 
  @ijxstice4 ай бұрын

  Can I use this sata to 8pin connector for my new rx580 GPU, I have power supply but don't have 8 pin connector with it!!

• 
  @Bfballin165 ай бұрын

  When you put the flash drive in how do you get those options to appear on the PlayStation 2? Mine isn't doing it at all I have to Playstation 2s a slim and a original one neither of them showed those options with 3 different flash drives

• 
  @thequintessentialgamer75145 ай бұрын

  Not sure what options you're referring to but it sounds like you didn't softmod your system first. You need a free mcboot memory card inserted when you power on your ps2

• 
  @Bfballin165 ай бұрын

  Yea that was the problem I've figured it out. Thanks

• 
  @Nora-oq5sz5 ай бұрын

  10:39

• 
  @user-sw6ez8nf7x5 ай бұрын

  Can someone help me where so I plug in my pcie cable 6 pin I know in the graphics card but what about the other slot thing

• 
  @user-sw6ez8nf7x5 ай бұрын

  I bought a 1650 from a gt 750 I think it was

• 
  @Nora-oq5sz5 ай бұрын

  3:03 8:52 11:36 13:57 25:07 26:17

• 
  @damm19575 ай бұрын

  My GeForce 980 has 2, 6 pin connectors. Should I connect two adapters to the 980?

• 
  @damm19575 ай бұрын

  Mine has 2 6pin connectors. Do I connect them both to a sata with the adapter?

• 
  @vgnlda5 ай бұрын

  I use a RX 6600 8GB Powercolor in my HP Elitedesk 8300 MT with a Sata to 8-pin connector. Works like a charm in 2024 (i7 3770 + 32 GB DDR3 + 2TB SSD + 2 TB HD) for 1080p gaming and everything else you can throw at it.

• 
  @DragonLawyer5 ай бұрын

  Fantastic video and exactly what I was looking for!

• 
  @Tcxqx6 ай бұрын

  Thank you so much I been looking for so long and every video didn’t help beside you ❤

• 
  @ashuprakash90066 ай бұрын

  THANK YOU SO MUCH

• 
  @Yonkolvl6 ай бұрын

  How do you do it without disabling the hard drive?

• 
  @Yonkolvl6 ай бұрын

  Life saver🙏

• 
  @AcidumAscorbinicum6 ай бұрын

  Thanks, it helped me a lot. The process on the Mac is basically the same.

• 
  @cyganski946 ай бұрын

  @mrdzinold to ty?

• 
  @Swarailiaball7 ай бұрын

  New title: How to never pay mortgage again with this one simple trick: pyrotechnics edition.

• 
  @DJPhrost7 ай бұрын

  I think your audio stuttered, sounded like you said, "to be neater" -- you should post edit videos, you woulda caught that and fixed in the dubover to be "cheaper."

• 
  @thequintessentialgamer75147 ай бұрын

  Actually I did catch that but left it in there so that someone with OCD would comment on it 4 years later.

• 
  @Magxmaa7 ай бұрын

  lucky to be the 1k sub

• 
  @Alexandro-so9jb7 ай бұрын

  2:21 the ps2 definetly would have recognised it. Problem is that some storage products need more power. For example I have an old hard drvie that i run my ps2 games from on OPL. If I where to connect it to my ps2 it would work just fine. But I have another, a newer one, which doesnt work when I plug it into the ps2's usb porn but it works on my router. Just a problem of power.

• 
  @Alexandro-so9jb7 ай бұрын

  2:46 If you go to mode there is an option to see what game these files belong to. Also 2:53 you can copy all of them at once. Or just press x to the ones you want.

• 
  @JeffRenko7 ай бұрын

  Bro ur pc is so old Also don't use that adapter is a fire hazard. how do I know this well I had learn the hard way of frying my gpu and the psu😢

• 
  @JeffRenko7 ай бұрын

  I did buy a new GAMING PSU WITH DUAL 8 PINS for 15 bucks on Facebook marketplace? WELL it's works fine no problems! no link? Why cus I think he took down the listing. YeS I also got a new gpu from the SAME PLACE.😮🎉

• 
  @thequintessentialgamer75147 ай бұрын

  You're really into yourself, aren't you?

• 
  @Lifebydesignvlogs7 ай бұрын

  I can't seem to located the power supply for my GEFORCE RTX 4060

• 
  @ovidiosakfree75378 ай бұрын

  luck brought me to this video. thanks a lot. this the real information i needed.

• 
  @Reman19758 ай бұрын

  The only problem with using those SATA to 6/8 pin adapters to power a GPU is the SATA power plug itself. They're "only" rated to 4.5A (So 54W). That sounds a bit pathetic when you think that 400+W GPU's are a thing now, but remember that the PCIe slot will be supplying up to 5.5 amps (66w *) on it's own, and if you're looking into using a SATA/8pin converter in your computer, you're probably not intending to run a RTX 3090 Ti in it anyway. So with a card that just uses up to 120w (something like a GTX 1060) it should be fine. A better option though would be to use the older 4 pin Molex connectors. Those bad boys were designed back when hard drives sucked big power, and are rated to a whopping 11A (132W) each, so with just a straight through 1x4 pin to 1x8 or 6 pin converter you'll get a much more usable 198W, and if you have 2 unused PSU cables with Molex plugs to turn over to GPU feeding duties (And your PSU has the neccecery wattage headroom on the 12v rail), you could run a 2x4 pin to 8 pin Y lead and pull 330W. (* Apparently some motherboards will now safely push the 16X PCIe slot up nearer to 6.25A, so 75W)

• 
  @cristiandavidaguillonangul17027 ай бұрын

  Good Answer. Thank you. With that in mind, I would like to ask you, Is it better to use a dual Molex to 8 Pin Connector using only One Molex Of these Two Connected, Would Work Fine for a month at least so I can save to purchase a new Power Supply Unit. It is a GTX960 and it's maximum Comsumption is 120 watts? Thanks in advance.

• 
  @Reman19757 ай бұрын

  @@cristiandavidaguillonangul1702 It depends on how the twin Molex to 8 pin cables wired. Most use 2 4pin molex plugs so the minimise the number of stubby jumper loops they need to get power to all the pins in the 8 pin end, so only connecting one of the 4 pin plugs may mean only 4 of the 8 pin plugs pins are getting power. IIRC, most 960's have a 8+6 pin power connector setup, so if it was me, and my PSU didn't have either a 6 or 8 pin plug, I'd probably just see what unused power connectors my PSU actually still had, then buy whatever adapters I would need so I could use those. With 66w already coming out of the PCIe slot, most of the remaining adapter options will be fine for the last 54w that this card needs........... Well, actually, I don't personally tend to use adapters. What I'll usually do in this situation would be to get some long 6 pin and 8 pin extension cables, cut the male plugs off, remove and open the PSU, then solder all the wires directly to the +12v and ground rails. Though to be honest, I wouldn't recommend this approach to anyone who hasn't played with electronics in the past as you really need to know what they're looking at or you could cause a pretty expensive problem. Back in the day I used to build my LAN party PC's into either clear acrylic cases, or one off open cases where everything was on show, so removing unnecessary power cables and making the remaining ones exactly the right length was pretty important for the over all clean look I'd be going for. Occasionally I'd need to add extra cables directly from the PSU so I didn't have multi connector cables strung between components. It isn't difficult, but as I said, if you're not 100% sure of what you're doing you're best to just use adapter cables.

• 
  @yezok018 ай бұрын

  Dont use tha sata adapter it cant handle thw current and you'll blow somthing up

• 
  @zeusphillips28619 ай бұрын

  you cant replace the motherbored in hp computers either because the io sheild does not come out of the case

• 
  @thequintessentialgamer75149 ай бұрын

  Yeah because thats the only hurdle to overcome when replacing a motherboard