Пікірлер

• 
  @ninasol55699 сағат бұрын

  I tried both side and I help my self with screw drivers not luck!

• 
  @leesweeten97717 күн бұрын

  I can get in using the Key. I will try getting a new Dura Cell Battery and see if that helps . It has been a few days since I opened the safe so when I punched in the code I notice none of the numbers/letters were beeping. So I felt the battery was dead. Went to town and got a new battery but not a dura cell as this small town did not have one.. Put new energizer mx battery in and same thing Only the # sound will beep. This is a Sentinel brand 24 gun safe.. I had used an energizer battery before and it worked for about 4 months then this. How much trouble is it to change the key pad if it went bad....

• 
  @leesweeten97717 күн бұрын

  I can punch the # sign and the key pad beeps as it should. But none of the numbers beep when I punch in my code So what is the issue.

• 
  @GuardianSafeAndLock7 күн бұрын

  If you’ve entered the wrong code a few times it may be on a 5min time out….. so wait 5-10min then try again. Otherwise the keypad is defective and it’s time to call a locksmith.

• 
  @QuadTap7 күн бұрын

  so the hunter series doesn't have a relocker?

• 
  @QuadTap7 күн бұрын

  nevermind... says on hollon site that hunter series has relocking

• 
  @GuardianSafeAndLock7 күн бұрын

  Yes it does have one it’s just a standard one though not a glass relocker

• 
  @daviedood25037 күн бұрын

  Not sure if u still read these. U said marine battery to fully drain and recharge, what about a golf cart battery? Both still 12 volts, it'd save space and cost less and still run just as long instead if a long heavy boat battery? Many thanks for making this, very curious how it all worked. 🤘😎🔥

• 
  @GuardianSafeAndLock9 күн бұрын

  Thanks for watching! Did you have any further questions on access control? Did you enjoy the video? Let us know here in the comments section!

• 
  @sjaron2313 күн бұрын

  Thank you!!

• 
  @pxpajxhn877515 күн бұрын

  I’m just tryna pick locks bro

• 
  @Sondos-yv4kk16 күн бұрын

  You’ve saved my life thank you 😂

• 
  @ColaTai21 күн бұрын

  Thank you i have the tool and now i know how to use it

• 
  @GuardianSafeAndLock22 күн бұрын

  Thanks for watching another episode of Picking the Brain! Hope you enjoy.

• 
  @serpentrae22 күн бұрын

  how about when start the engine and you can pull the key straight out in all positions with out turning the key while the engine is running are not

• 
  @GuardianSafeAndLock22 күн бұрын

  I’ve had this happen before it’s the retainer on the ignition only way to fix is to replace the ignition! 👍🏻

• 
  @serpentrae22 күн бұрын

  @@GuardianSafeAndLock ok thank you for replying back, so can i get a used ignition and have it re keyed at a lock smith so i can use my original key, thank you again

• 
  @nite921823 күн бұрын

  SHIT WORKED SO WELL🙏🗣️‼️💯💯

• 
  @user-om6mm8zy9m28 күн бұрын

  شكرا❤

• 
  @Betterifitsfree29 күн бұрын

  Great demo. Why not mess up the passenger side rather than create damage or leaks on the driver side?

• 
  @GuardianSafeAndLock29 күн бұрын

  If you do a good job there should be no damage, but yeah if we weren’t making this video on our truck for video purposes the passenger door is our go to….

• 
  @calicowgirl170029 күн бұрын

  Doesnt work

• 
  @GuardianSafeAndLock29 күн бұрын

  Next step…. Time to call a professional, must be something a little more involved.

• 
  @nsabimanajeandamour412Ай бұрын

  How can I get that machine how much does it buy?

• 
  @brooklynant2047Ай бұрын

  Didn’t help me because I found it was hard to put my finger on the small space and try to pull the key out. Actually hurt trying to keep my finger on there and hold it by pushing. So no it wasn’t that easy I’m afraid.

• 
  @GuardianSafeAndLockАй бұрын

  Next step is to call a locksmith then.

• 
  @erikamay3146Ай бұрын

  Oh my gosh thank you I watched ur vido it worked ❤thank u so much

• 
  @egggleg272Ай бұрын

  doesn't work at all

• 
  @GuardianSafeAndLockАй бұрын

  Guess it’s time to call a professional

• 
  @michealplatinwangi4442Ай бұрын

  Am really interested in this trade. Am in Qatar 🇶🇦 and I seek help and guidance on how to become one!!!

• 
  @kristophermckinley4497Ай бұрын

  The new ignition comes with a key but does the key for the 2010 Ford F150 xlt.

• 
  @cg7422Ай бұрын

  Thanks! Worked for me!

• 
  @XoLilyXo_12Ай бұрын

  Thank you so much you saved me and my grandma who had been stuck outside it 90 degrees heat for 20 minutes

• 
  @customerservice4188Ай бұрын

  Can a panic bar be used in conjunction with it and how would the panic bar disarm the magnet lock once its depressed

• 
  @lanajacknichols8397Ай бұрын

  That’s a 2003 Ford Taurus transformer key and a 2003 Ford escape transport key have the same frequency

• 
  @tonyfanguy5977Ай бұрын

  Thanks So Much,I was Freaking out. I called the manufacturer and they didn’t know…. I Went get the Duracell And Hello Opened. I appreciate thank you for your knowledge…

• 
  @Amnah-ln7Ай бұрын

  اعجبتني كنت سأكسر قفل الصندوق حقا اشكرك لقد كنت احاول اخراجه منذ ساعة كاملة شكراً جزيلاً لك

• 
  @flyladydiАй бұрын

  IT WORKED I LOVE YOU

• 
  @fkeys9575Ай бұрын

  Well done . where do get the metal draws from ? I am searching around for a good deal .

• 
  @user-rp9ev5cv8lАй бұрын

  Good info

• 
  @makaveli2ttАй бұрын

  Very helpful. Thank you

• 
  @swittykoh17Ай бұрын

  I wanna start doing this i just hope i hav money for all of this

• 
  @MelissaGranados-yd2xyАй бұрын

  4 new Duracells and it beeps once when attaching. Then push buttons and nothing. Is it the wiring ? Can that be replaced?

• 
  @Bludrzl99Ай бұрын

  I’m having the exact same issue

• 
  @HuntsWorkshopАй бұрын

  I hold a business card behind the slim jim right down at the weatherstrip and it doesn't scratch any visible area of the window, even on a dodge ram where you know you need that inward bend that likes to scratch.

• 
  @prescottc46282 ай бұрын

  Do you guys have an intro or basics playlist put together? I'm waiting on some material for my course and wanted to get ahead.

• 
  @prescottc46282 ай бұрын

  He's describing keys like Bubba described how to cook shrimp. 😂😂😂

• 
  @Talz822 ай бұрын

  Just saved me! I’ve been standing here trying to get a key out for half hour! Thanks legend!!!

• 
  @irenedornberger89892 ай бұрын

  This wasn't covered. If it locks when you go in, say a residence, how do you unlock it from inside?

• 
  @GuardianSafeAndLock2 ай бұрын

  The lever that engages with the strike is always unlocked from the inside, so you just push the lever down and exit.

• 
  @angelmora66462 ай бұрын

  just wanted to say thank you so much for this video - I realized I needed special tools. With your knowledge and proper tools I managed to get the key out. FYI the key broke perfectly where there was no way of going over it.

• 
  @jannatulnaimqueen57472 ай бұрын

  My key is still stuck 😭😔😭😔. about 4hours

• 
  @FarhadJabiyev2 ай бұрын

  Thanks man! Lifesaver 😊

• 
  @golf-n-guns2 ай бұрын

  Wd40 has a Teflon spray. Really slicks up a lock!

• 
  @doorandlocktips2 ай бұрын

  Great video

• 
  @stevenaird59252 ай бұрын

  Can you place barrel key round key that is missing that is missing

• 
  @davidturner65092 ай бұрын

  A long reach tool is my last resort rather than my go to.

• 
  @superdutyohv34012 ай бұрын

  The Amsec “almalgamation of steel nuggets and fiber” in the composite fill gave that drill hell! Cool video! If anyone has high valuables don’t settle for anything less than TL30 bolted down. Gun safes are a joke…

• 
  @Jackrodder2 ай бұрын

  I had a couple keys on me for years since I'm alive, but I never asked anybody how they are made or how they are copied. Well, now I know the copy part! It seems so simple but still it needs perfect alignment on the machine and the machine itself has to be exact down to the mm. Interesting topic!

• 
  @iexist60212 ай бұрын

  Helpful. Thanks

• 
  @damianstrudley22652 ай бұрын

  Very good video.. thank you...