To get better results from ONR Rinseless Wash and Wax your mit is too dripping wet and you should clean in one vertical motion from left to right, one panel at a time and than dry with a clean soft micro fiber towel abd than buff with another soft clean dry micro fiber towel
@kodai_fa55 ай бұрын
This is what I do: Use 2 gallons distilled water with 4-6 cap-fulls of ONR In your 1st bucket. Put 4 clean 🎉🎉wash mitts in that same 1st bucket. Then fill a 2nd bucket with regular hose water and a grit guard. The 2nd bucket will be used to wash your mitts at the end. No need to pre-spray or soak if it's only dusty or lightly dirty. Split the car into 4 quadrants, using 1 clean mitt per quadrant. Start at the roof and work🎉🎉 side to side, all the way down. At the end of each quadrant, put the used mitt in the 2nd plain hose water bucket with the grit guard. After all 4 quadrants are done, you'll have 4 dirty mitts in the 2nd bucket. Use the grit guard to scrub the 4 mitts clean, then hang them to dry. Use the remaining ONR bucket water to fill your spray bottle. Go around the car with 4-6 clean microfiber towels to dry. Look for any dry spots or streaks that need extra lubrication and wipe as needed. Remember to never cross contaminate. Once a mitt touches the car, it doesn't go back into your ONR bucket.
@aerialphotography836310 ай бұрын
Mix ONR and wash medium in a bucket. Have a rinse bucket nearby.
@aerialphotography836310 ай бұрын
2 buckets bro… wtf are you doing. You are scratching everyone’s paint. And I say everyone because you claim to be a pro and yet you can’t read directions? Instead of reading the instructions you decide to make a KZread video. I hope anyone that calls themselves a detailer would have some common sense
@MrChuckwagon55 Жыл бұрын
The car needs to be clayed & polished.
@linaepaulsen6302 Жыл бұрын
Maybe you should try distilled water.
@konradsmorawski7941 Жыл бұрын
What dillution in pre-spray spray gun?
@om39732 жыл бұрын
Those look like water spots probley was on there before try water spot remover if dosentc work you need to polish if you keep car outside itasca endless battle would do once year get it better and leave it alone you can try kotch fse
@GT2Scirocco3 жыл бұрын
you cant prepare this two products, Meguiar's ultimate Quick detailer is a cleaner for light pollution product without any wax. The bsd is a wax detailer!!
@RnBGarvey2 жыл бұрын
you just said the same thing two different ways
@justinsteel63603 жыл бұрын
What a crap test. The 4 sections were at different angles. Shouldve had vertical split. Extra gloss protection needs a good shake for a while prior to application too.
@dlmhdlmh3 жыл бұрын
The tape won
@freshday6334 жыл бұрын
i would pressure wash the hole car first being as dirty as it is then 2 bucket method with a good car shampoo dry it then use optimum no rinse wash and wax. do all of this in the evening with no sun to help STOP water spots I WOULD THEN USE THIS OPTIMUM WASH AND WAX ONLY WHEN THE CAR HAS A BIT OF DUST ON IT
@MrTunes3334 жыл бұрын
It's also about how quick they can be applied and Autoglyn wins there..
@ryanmclaren98734 жыл бұрын
This is ridiculous bro. These are DETAILERS products. These are designed for gloss appearance not protection. Use a wax then you use a detailer afterwards. And they are both great products. It just you own personal preference. I would sonax was better in this video..
@RnBGarvey2 жыл бұрын
bsd is more about water beading than gloss .
@petethompson12824 жыл бұрын
Youll find Sonax makes scratches worse looking as it has cleaners, yet looks much much more glossy and water repellant. Their wax is the same, its mental as a sealant but your paint has to be spot on else it shows you its flaws. Ive since gone back to meguirs ultimate polish and nxt 2.0 as it hides everything, perfect for daily drivers
@RnBGarvey2 жыл бұрын
try sonax cleaner wax.
@steverabbits4 жыл бұрын
BSD for me. It was fortuitous that it rained as you applied it because it works better with a small amount of water than neat! Many use it 50:50 to help with slick application and Brian at Apex Detailing even recommends using it 5:1 as a maintenance product. Try using BSD as a top layer on top of Sonax Net Shield then Sonax Spray and Seal. Apparently it's as good as a light ceramic and will give a year or more protection when maintained with BSD. Apex have made a video of that exact triple system.
@tomas19cronin4 жыл бұрын
What’s all this two bucket nonsense about it’s onr you don’t need two buckets your just be watering down the solution. Onr won’t causes scratches
@clementte69484 жыл бұрын
waterspot .... nothing you can do about that but to use some waterspot remover over it first before soaping it ..... moreso, use distilled water as well. And maybe dont wash under the sunlight. you can try spraying it with some quick detailer before wiping it dry too :)might help
@thephantomarse85254 жыл бұрын
Good test the colinite looked the best best before i knew what it was Amazing how similar they all looked though i guess its down to how long they all last
@detailingdiaries65624 жыл бұрын
I've had the collinite on all winter and it's doing great. 👍
@thephantomarse85254 жыл бұрын
Im currently trying different waxes For durabillity i will have to get some colinite Soft 99 Fuso coat is meant to be really good too but they have recently changed the formula
@russellparker45684 жыл бұрын
Megs takes 12 hours to cure
@detailingdiaries65624 жыл бұрын
According to whom? 🤔
@russellparker45684 жыл бұрын
@@detailingdiaries6562 the instructions on the back of the bottle 😉
@scottlucas22815 жыл бұрын
No snow foam on the car first?
@TheDoosh795 жыл бұрын
I have a real problem applying the Sonax BSD, I've been washing, polishing and waxing cars for decades but I find this stuff a real pain. It's grabby and not very easy to take off, plus it leaves a blotchy finish, when I stand back I can clearly see an uneven finish on the paint work even though it's been applied and removed evenly.
@hernandez33085 жыл бұрын
Clay bar
@juanjovillafana89545 жыл бұрын
El producto de SONAX es un poco mejor, casi iguales en cuanto a aplicación y propiedades, pero si considerámos que su botalla contiene 25% más producto y cuesta 20% menos que el Quik Detailer de Meguiar's pues el resultado es contundente.... Saludos desde San Pedro Cholula, Puebla, México.
@RobertSmith-di5ll5 жыл бұрын
no difference - can anyone justify choosing one or the other?
@detailingdiaries65625 жыл бұрын
The spray head is better on Megs, but the price of BSD is around half as much. I just decant BSD into a better bottle.
@chillisauce60795 жыл бұрын
Good vid. Thanks for the in-depth comparison. Would like to know how my go to QD, AG Aqua Wax compares to these two. Thinking of trying BSD next though, heard a lot of good things about it and you didn't find it grabby either.
@detailingdiaries65625 жыл бұрын
No I have never found it grabby at all, but I think those who do find it grabby is when its on hot days and in direct sun. In those conditions the paintwork can get very hot and I guess it flashes off too quickly. In the UK it doesn't seem to have much of a problem. The other thing about BSD is that it's SO cheap. From Carparts4less I was able to get 2 bottles (1.5l total) delivered for something like £13. Megs is probably closer to £16 for 700 or 750ml.
@chillisauce60795 жыл бұрын
@@detailingdiaries6562 Thanks for the reply mate. I never wash in direct sun so hopefully it will lay down ok. What was the long term longevity like, sometimes I have to go 6 weeks between washes, do you think it will last this long? It will be used as a top up wax on top of BH Double Speed wax which I have been impressed with btw. One last question if I may, I like the idea of putting QDs on at the drying stage and AG Aqua Wax is designed to be used this way. Do you know if BSD can be used like this on a wet car? Thanks.
@antoniomartins78005 жыл бұрын
Sonax bsd vs ultimate fast finish meguias??
@detailingdiaries65625 жыл бұрын
I've not tried Fast Finish, have you? It seems more of a spray sealant, rather than a quick Detailer though.
@antoniomartins78005 жыл бұрын
@@detailingdiaries6562 sonax bsd x ultimate fast finish meguias, your favorite?
@detailingdiaries65625 жыл бұрын
@@antoniomartins7800 I haven't tried Ultimate Fast Finish.
@juanjovillafana89545 жыл бұрын
Hi Antonio..... Not it's the same products. Polimer Net Shield by SONAX VS Ultimate Fast Finish by Meg's 👍👍👍 Saludos desde San Pedro Cholula, Puebla,México.
@atelierelehandmade5 жыл бұрын
lol read the instruction lollllllllllllllllllllllllllllllllllllllllll use your head corect
@aeb0076 жыл бұрын
Great video! Can you add the Autoglym Extra Gloss Protection after waxing the car? or must you apply polish first and the wax?
@detailingdiaries65626 жыл бұрын
Hi, you wouldn't need to do both, either use a wax, or a sealant like Extra Gloss Protection. You don't need to polish, but if you wanted to you can. If you are doing it by hand, I recommend Autoglym Super Resin Polish followed by Extra Gloss Protection, they are designed to work together 👍
@princeh40326 жыл бұрын
Hey good work! You did it by hand? Or with discs and a DA? It'd be nice to see at least some of the process. So you used 1500 then 2000, 3000, 5000? Usually you only need 1500 then 3000. You sure that was needed? As a good compound or single stage should take care of 2000+
@detailingdiaries65626 жыл бұрын
Thanks, I used the wet sand paper with a sanding block for that stage, and then a rotary for compounding and polishing. I'm still learning, so I could well be doing too many stages!
@princeh40326 жыл бұрын
@@detailingdiaries6562 using wetsanding discs on a DA is actually less aggressive and more even than blocks. Be I'll try find a good video for you with advice from Jason Rose
Hi, I hope anybody can support me. My car has the SONAX Profiline Ceramic Coating cc36 and I'm looking to extend the water repelent feature and keep the shine after weekly wash without affect the coating. I have used the Meg's Ultimate Quik Detailer for many years but I'm affraid to use it because it's a different brand product. Do you know if using this Meg's Detailer can affect the coating or it will better to get the SONAX Detailer to do it? Seeing this video it's shown both are good products but don't know if the ingredients used in Meg's could drop the ceramic coating. Thank you in advance.
@totowolf97166 жыл бұрын
The diff is that sonax doesn’t use silicone and lasts weeks where the megs last a few days
@detailingdiaries65626 жыл бұрын
toto wolf did you watch until the end to see the durability part?
@totowolf97166 жыл бұрын
Detailing Diaries apparently not
@raksh96 жыл бұрын
Ultimate Quik Detailer instructions say to wait for 12 hours for the polymer crosslinking to set. Leaving it in the rain right after application doesn't seem like the best test.
@detailingdiaries65626 жыл бұрын
raksh9 interesting, it doesn't say that on my UK bottle, which country did you get your bottle in? Unfortunately I don't have anywhere else to detail my car, so it's up to the elements if the car gets wet or not. I hope you enjoyed the video.
@RnBGarvey2 жыл бұрын
a qd needing to cure is ridiculous
@peterh83536 жыл бұрын
next step soft clay i guess, onr as lube..
@K2edg6 жыл бұрын
How did they stand up over time?
@JohnRocker3406 жыл бұрын
Collinite
@Parasoll306 жыл бұрын
It would have been fun to se the hood of the car 1,2,3 and 6 mont`s later.
@paulcolmer836 жыл бұрын
Try Fusso. Applied 8 months ago , 15000 miles later it is still beading like when first applied. Even my body shop guy borrowed it for his own car!
@kenlawton15316 жыл бұрын
Paul Colmer You simply can't beat fusso coat.
@Burgring83137 жыл бұрын
super video
@nageshtagadur7 жыл бұрын
I am just like you,... I try out many kinds of polish, sealants myself, until I can sleep peacefully,...........
@ibuprofen3037 жыл бұрын
I've been drinking a bottle of Autoglym a night, but it never makes me sleepy. I might change brand.
@nageshtagadur7 жыл бұрын
I said I try out different polishes/ sealants etc on my vehicles, not on myself...........
@ibuprofen3037 жыл бұрын
That's probably where I've been going wrong. Thanks for the advice!
@kenlawton15316 жыл бұрын
ibuprofen303 😂
@rikkografi7 жыл бұрын
Great video. I Honestly could see it was autoglym, the other ones where impossible, thought Collinite was FK 1000p
@BuckeyeMCS7 жыл бұрын
I know you cant try them all but Collinite #915 is better than 476 IMHO
@detailingdiaries65627 жыл бұрын
BuckeyeMCS I might try it if I do another test. With panel pots its only about £5 a pot, but I don't think Collinite do them, but their full pots are only around £10 a pot, so not too expensive, however a full sized pot for someone only doing their own car will last for several years, so a bit of a waste IMHO.
@travisclarkin42777 жыл бұрын
Visually I cannot tell any difference...cool video
@davepuffett86087 жыл бұрын
BSD every time for me, what's the cost comparison? Mega alway seems a bit more expensive? Good test tho m8! 👍
@detailingdiaries65627 жыл бұрын
Dave Puffett I think the Megs is about twice the price of BSD as you can often find BSD heavily discounted
@kev008ify7 жыл бұрын
The left one !!
@qualityswisswatches17 жыл бұрын
is that the angel of the north reflecting in your bonnet?..lol
@CheebaTimeTv6 жыл бұрын
No its the swirl from the south
@rahuldavid14107 жыл бұрын
i think autoglym was best
@detailingdiaries65627 жыл бұрын
Rahul David thanks, the AG EGP is my go to sealant, so easy and fast to apply and the longevity is great 👍
@babattaja6 жыл бұрын
It had the worst beading though..
@SZTILER7 жыл бұрын
sonax połowę tańszy a efekt taki sam ;))Wielkie dzięki
@susancordon7 жыл бұрын
I've just wasted 16 minutes and 2 seconds plus 1 minute writing this.
@detailingdiaries65627 жыл бұрын
Sue Cordon I'm glad you watched it all the way to the end 👍
@Amathusukx5 жыл бұрын
My Wife would say the same, yet she'd expect her car to look nice.
@LoochMindReader7 жыл бұрын
I've been using Sonax BSD for a couple years now and is a wonderful product with very good longevity for a QD.
Пікірлер
To get better results from ONR Rinseless Wash and Wax your mit is too dripping wet and you should clean in one vertical motion from left to right, one panel at a time and than dry with a clean soft micro fiber towel abd than buff with another soft clean dry micro fiber towel
This is what I do: Use 2 gallons distilled water with 4-6 cap-fulls of ONR In your 1st bucket. Put 4 clean 🎉🎉wash mitts in that same 1st bucket. Then fill a 2nd bucket with regular hose water and a grit guard. The 2nd bucket will be used to wash your mitts at the end. No need to pre-spray or soak if it's only dusty or lightly dirty. Split the car into 4 quadrants, using 1 clean mitt per quadrant. Start at the roof and work🎉🎉 side to side, all the way down. At the end of each quadrant, put the used mitt in the 2nd plain hose water bucket with the grit guard. After all 4 quadrants are done, you'll have 4 dirty mitts in the 2nd bucket. Use the grit guard to scrub the 4 mitts clean, then hang them to dry. Use the remaining ONR bucket water to fill your spray bottle. Go around the car with 4-6 clean microfiber towels to dry. Look for any dry spots or streaks that need extra lubrication and wipe as needed. Remember to never cross contaminate. Once a mitt touches the car, it doesn't go back into your ONR bucket.
Mix ONR and wash medium in a bucket. Have a rinse bucket nearby.
2 buckets bro… wtf are you doing. You are scratching everyone’s paint. And I say everyone because you claim to be a pro and yet you can’t read directions? Instead of reading the instructions you decide to make a KZread video. I hope anyone that calls themselves a detailer would have some common sense
The car needs to be clayed & polished.
Maybe you should try distilled water.
What dillution in pre-spray spray gun?
Those look like water spots probley was on there before try water spot remover if dosentc work you need to polish if you keep car outside itasca endless battle would do once year get it better and leave it alone you can try kotch fse
you cant prepare this two products, Meguiar's ultimate Quick detailer is a cleaner for light pollution product without any wax. The bsd is a wax detailer!!
you just said the same thing two different ways
What a crap test. The 4 sections were at different angles. Shouldve had vertical split. Extra gloss protection needs a good shake for a while prior to application too.
The tape won
i would pressure wash the hole car first being as dirty as it is then 2 bucket method with a good car shampoo dry it then use optimum no rinse wash and wax. do all of this in the evening with no sun to help STOP water spots I WOULD THEN USE THIS OPTIMUM WASH AND WAX ONLY WHEN THE CAR HAS A BIT OF DUST ON IT
It's also about how quick they can be applied and Autoglyn wins there..
This is ridiculous bro. These are DETAILERS products. These are designed for gloss appearance not protection. Use a wax then you use a detailer afterwards. And they are both great products. It just you own personal preference. I would sonax was better in this video..
bsd is more about water beading than gloss .
Youll find Sonax makes scratches worse looking as it has cleaners, yet looks much much more glossy and water repellant. Their wax is the same, its mental as a sealant but your paint has to be spot on else it shows you its flaws. Ive since gone back to meguirs ultimate polish and nxt 2.0 as it hides everything, perfect for daily drivers
try sonax cleaner wax.
BSD for me. It was fortuitous that it rained as you applied it because it works better with a small amount of water than neat! Many use it 50:50 to help with slick application and Brian at Apex Detailing even recommends using it 5:1 as a maintenance product. Try using BSD as a top layer on top of Sonax Net Shield then Sonax Spray and Seal. Apparently it's as good as a light ceramic and will give a year or more protection when maintained with BSD. Apex have made a video of that exact triple system.
What’s all this two bucket nonsense about it’s onr you don’t need two buckets your just be watering down the solution. Onr won’t causes scratches
waterspot .... nothing you can do about that but to use some waterspot remover over it first before soaping it ..... moreso, use distilled water as well. And maybe dont wash under the sunlight. you can try spraying it with some quick detailer before wiping it dry too :)might help
Good test the colinite looked the best best before i knew what it was Amazing how similar they all looked though i guess its down to how long they all last
I've had the collinite on all winter and it's doing great. 👍
Im currently trying different waxes For durabillity i will have to get some colinite Soft 99 Fuso coat is meant to be really good too but they have recently changed the formula
Megs takes 12 hours to cure
According to whom? 🤔
@@detailingdiaries6562 the instructions on the back of the bottle 😉
No snow foam on the car first?
I have a real problem applying the Sonax BSD, I've been washing, polishing and waxing cars for decades but I find this stuff a real pain. It's grabby and not very easy to take off, plus it leaves a blotchy finish, when I stand back I can clearly see an uneven finish on the paint work even though it's been applied and removed evenly.
Clay bar
El producto de SONAX es un poco mejor, casi iguales en cuanto a aplicación y propiedades, pero si considerámos que su botalla contiene 25% más producto y cuesta 20% menos que el Quik Detailer de Meguiar's pues el resultado es contundente.... Saludos desde San Pedro Cholula, Puebla, México.
no difference - can anyone justify choosing one or the other?
The spray head is better on Megs, but the price of BSD is around half as much. I just decant BSD into a better bottle.
Good vid. Thanks for the in-depth comparison. Would like to know how my go to QD, AG Aqua Wax compares to these two. Thinking of trying BSD next though, heard a lot of good things about it and you didn't find it grabby either.
No I have never found it grabby at all, but I think those who do find it grabby is when its on hot days and in direct sun. In those conditions the paintwork can get very hot and I guess it flashes off too quickly. In the UK it doesn't seem to have much of a problem. The other thing about BSD is that it's SO cheap. From Carparts4less I was able to get 2 bottles (1.5l total) delivered for something like £13. Megs is probably closer to £16 for 700 or 750ml.
@@detailingdiaries6562 Thanks for the reply mate. I never wash in direct sun so hopefully it will lay down ok. What was the long term longevity like, sometimes I have to go 6 weeks between washes, do you think it will last this long? It will be used as a top up wax on top of BH Double Speed wax which I have been impressed with btw. One last question if I may, I like the idea of putting QDs on at the drying stage and AG Aqua Wax is designed to be used this way. Do you know if BSD can be used like this on a wet car? Thanks.
Sonax bsd vs ultimate fast finish meguias??
I've not tried Fast Finish, have you? It seems more of a spray sealant, rather than a quick Detailer though.
@@detailingdiaries6562 sonax bsd x ultimate fast finish meguias, your favorite?
@@antoniomartins7800 I haven't tried Ultimate Fast Finish.
Hi Antonio..... Not it's the same products. Polimer Net Shield by SONAX VS Ultimate Fast Finish by Meg's 👍👍👍 Saludos desde San Pedro Cholula, Puebla,México.
lol read the instruction lollllllllllllllllllllllllllllllllllllllllll use your head corect
Great video! Can you add the Autoglym Extra Gloss Protection after waxing the car? or must you apply polish first and the wax?
Hi, you wouldn't need to do both, either use a wax, or a sealant like Extra Gloss Protection. You don't need to polish, but if you wanted to you can. If you are doing it by hand, I recommend Autoglym Super Resin Polish followed by Extra Gloss Protection, they are designed to work together 👍
Hey good work! You did it by hand? Or with discs and a DA? It'd be nice to see at least some of the process. So you used 1500 then 2000, 3000, 5000? Usually you only need 1500 then 3000. You sure that was needed? As a good compound or single stage should take care of 2000+
Thanks, I used the wet sand paper with a sanding block for that stage, and then a rotary for compounding and polishing. I'm still learning, so I could well be doing too many stages!
@@detailingdiaries6562 using wetsanding discs on a DA is actually less aggressive and more even than blocks. Be I'll try find a good video for you with advice from Jason Rose
@@detailingdiaries6562 kzread.info/dash/bejne/o2ShvLJ-itfXYto.html
Hi, I hope anybody can support me. My car has the SONAX Profiline Ceramic Coating cc36 and I'm looking to extend the water repelent feature and keep the shine after weekly wash without affect the coating. I have used the Meg's Ultimate Quik Detailer for many years but I'm affraid to use it because it's a different brand product. Do you know if using this Meg's Detailer can affect the coating or it will better to get the SONAX Detailer to do it? Seeing this video it's shown both are good products but don't know if the ingredients used in Meg's could drop the ceramic coating. Thank you in advance.
The diff is that sonax doesn’t use silicone and lasts weeks where the megs last a few days
toto wolf did you watch until the end to see the durability part?
Detailing Diaries apparently not
Ultimate Quik Detailer instructions say to wait for 12 hours for the polymer crosslinking to set. Leaving it in the rain right after application doesn't seem like the best test.
raksh9 interesting, it doesn't say that on my UK bottle, which country did you get your bottle in? Unfortunately I don't have anywhere else to detail my car, so it's up to the elements if the car gets wet or not. I hope you enjoyed the video.
a qd needing to cure is ridiculous
next step soft clay i guess, onr as lube..
How did they stand up over time?
Collinite
It would have been fun to se the hood of the car 1,2,3 and 6 mont`s later.
Try Fusso. Applied 8 months ago , 15000 miles later it is still beading like when first applied. Even my body shop guy borrowed it for his own car!
Paul Colmer You simply can't beat fusso coat.
super video
I am just like you,... I try out many kinds of polish, sealants myself, until I can sleep peacefully,...........
I've been drinking a bottle of Autoglym a night, but it never makes me sleepy. I might change brand.
I said I try out different polishes/ sealants etc on my vehicles, not on myself...........
That's probably where I've been going wrong. Thanks for the advice!
ibuprofen303 😂
Great video. I Honestly could see it was autoglym, the other ones where impossible, thought Collinite was FK 1000p
I know you cant try them all but Collinite #915 is better than 476 IMHO
BuckeyeMCS I might try it if I do another test. With panel pots its only about £5 a pot, but I don't think Collinite do them, but their full pots are only around £10 a pot, so not too expensive, however a full sized pot for someone only doing their own car will last for several years, so a bit of a waste IMHO.
Visually I cannot tell any difference...cool video
BSD every time for me, what's the cost comparison? Mega alway seems a bit more expensive? Good test tho m8! 👍
Dave Puffett I think the Megs is about twice the price of BSD as you can often find BSD heavily discounted
The left one !!
is that the angel of the north reflecting in your bonnet?..lol
No its the swirl from the south
i think autoglym was best
Rahul David thanks, the AG EGP is my go to sealant, so easy and fast to apply and the longevity is great 👍
It had the worst beading though..
sonax połowę tańszy a efekt taki sam ;))Wielkie dzięki
I've just wasted 16 minutes and 2 seconds plus 1 minute writing this.
Sue Cordon I'm glad you watched it all the way to the end 👍
My Wife would say the same, yet she'd expect her car to look nice.
I've been using Sonax BSD for a couple years now and is a wonderful product with very good longevity for a QD.
How long would it last you ?