i just got one the other day do you use wifi or the usb drive
@abbyseagraves51122 ай бұрын
Still watching this video 2 years later❤ hope we get it again this CREEKEND
@mobiletechnologystar7 ай бұрын
Resigned with no leave notice angle grinder hhhh
@tonysanderson77412 жыл бұрын
Is this still a good 3d printer in 2022?
@neilhagan55662 жыл бұрын
If you are able to scoop one up for cheap then yeah actually.. throw a few bucks at it (if you have some free time) and it's a very capable machine. That said you can snag an ender 3 for 99 bucks every now and then... It's honestly all relative to your location and what's available and what you want to put into it. Since this video I dumped 40 bucks into a direct drive end on an xvixo x3s and that I picked up for 60 bucks and it prints like a dream.. reviews on 3d printers are honestly a joke anymore... Years ago if you wanted out of the box ease of use these were about all you had... I believe Anker (the electronics go to on Amazon) has a Kickstarter for a printer that looks promising. Throw money towards it if your not in a hurry. To me that looks promising... 3d printing can be a headache if you are just starting out. That said once you have owned a few machines it's not uncommon to start a print on a machine leave for work and come home to a decent print now-a-days.. if you ask me my opinion anymore (I've owned over 30 printers in the past few years)... I have found that the ones you tinker with the most will always be your go to... I have built a couple hypercube based printers that I really loved.. I had a lot of time in them... I spent 60 bucks on your basic ender3 clone and put a different hot end on it and had excellent results... This reply probably does not help much but what I'm getting at is if you put some time into this guy yeah it's a very capable printer... Maybe snag one of these used and throw in a different board and your set....
@tonysanderson77412 жыл бұрын
@@neilhagan5566 Thanks for the reply
@abbyseagraves51122 жыл бұрын
This still has me buzzing 💘
@ghan7253 жыл бұрын
Could you tell how do I fix the touch panel is not on issue?
@Del-Canada3 жыл бұрын
Ol Neilyboy.
@neilyboy3 жыл бұрын
Del how the heck have you been buddy!?
@Del-Canada3 жыл бұрын
@@neilyboy Just spinning in the marrow and living life. I finally got one of your notifications. KZread is consistently busted. D'oh! I hope you are doing well. Been a long time. KK is still up and the channel is still around.
@neilyboy3 жыл бұрын
@@Del-Canada I should swing into the good ol irc. It's our anniversary so the wife and I are heading out for s night out tonight
@nichellehowell4 жыл бұрын
How do you know he doesn't have a medical condition?
@Del-Canada4 жыл бұрын
The ol Neilyboy.
@MrYoung114 жыл бұрын
Is the camera being powered by the panel?
@neilyboy4 жыл бұрын
I have a couple 12v 7ah lead acid batteries in a waterproof box down below. The panel could power the camera but it would only be available when the sun is out of course.
@Del-Canada5 жыл бұрын
Is this Neilyboy from KK?
@neilyboy5 жыл бұрын
Delphinius! Sure is buddy how in the heck have you been!
@Del-Canada5 жыл бұрын
@@neilyboy LMAO Just doing the internet rounds and thought about you for some reason. I think I dropped by several years ago also. Heh.
@neilyboy5 жыл бұрын
@@Del-Canada that's awesome! Oh the good ol days of the interwebs. Any crazy projects lately? I am thinking about building a virtual pinball cabinet for the kids to play around with.
@Del-Canada5 жыл бұрын
@@neilyboy My legs were shot off back there in Okinawa.
@neilyboy5 жыл бұрын
@@Del-Canada don't need legs to play pinball
@jessewheeler93155 жыл бұрын
Was that ice water being recirculated through an immersion chiller and then through a CFC?? How long to cool? 3 mins???
@neilyboy5 жыл бұрын
It was fairly quick I could run directly from boil to fermentor and pitch shortly after
@Crypto_MarkX5 жыл бұрын
is this a good printer for a begginer?
@neilyboy5 жыл бұрын
Yeah. With its leveling features and filament options I think it's a great starter myself.
@Crypto_MarkX5 жыл бұрын
just ordered one should come in a week
@mikecanalelorieta90715 жыл бұрын
Did you provide product presentation or product demo on the site?
@neilyboy5 жыл бұрын
No I have no affiliation with xyz
@M3LLYM3L695 жыл бұрын
can anyone help me .... so purchase this same printer and i go and turn it on and the LED lights flashes and and the motor rides to the back of the wall and does this scraping sound .im just a beginner lol
@neilyboy5 жыл бұрын
@@M3LLYM3L69 any error number on screen? Where is the scraping noise coming from?
@M3LLYM3L695 жыл бұрын
@@neilyboy no nothing on the screen ....the axis is going all the way to the back and the LED lights does not turn on just a quick flash
@neilyboy5 жыл бұрын
@@M3LLYM3L69 interesting. You don't happen to see any loose wires anywhere do you? It sounds like a hardware fault of some kind to me. You just unboxed this? Davinci has good support. Where did you purchase?
@volvodr665 жыл бұрын
Just ordered the same unit. Should arrive in two days. Thanks for sharing your set-up video.
@MSMotivations5 жыл бұрын
Good job
@allansmallwood81255 жыл бұрын
But when you posted this I lived in metamora
@allansmallwood81255 жыл бұрын
I live there :D
@giorgosarab7 жыл бұрын
50 euro
@mooseworks_soldiers7 жыл бұрын
That looks like the basement from the first Ghostbusters movie.
@johnstratairious79367 жыл бұрын
I used a piece of glass cut just inside of the 4 brackets. I also use elmers glue stick and apply 5 cross coats of the glue on the glass. Then I use aluminum tape on the sides of the glass to hold the glass in place. When you do this if you do..you are going to have to reset your Z offset and use a business card for your clearance of the nozzle to the glass plate. I adjusted mine to where the card slides smoothly under the nozzle with just a tad of a grab by the nozzle. Then when the print is done i remove the glass and let it sit for about 10 minutes...the part should pull off easy. then i rinse my glass plate and re do the process when i want to print something else.
@axlslak5 жыл бұрын
The glue sticks are awful as adhesive. Try hairspray. Much easier to both apply and clean.
@clarenceney72665 жыл бұрын
John Stratairious what type power supplies?
@johnstratairious79367 жыл бұрын
I shared your video on face book so hopefully you'll get some more HITS. thanks again for the video brother.
@johnstratairious79367 жыл бұрын
yeah i got the one with the laser the scanner and of course the 3d printer. unboxed mine today on april 27 2017. can't wait to use it. thanks for the video...it was good.
@jjeei7 жыл бұрын
Hello, Do you know how turn on and turn off the leds from your control?
@neilyboy7 жыл бұрын
There may be alternate ways of doing this but if you wanted an all in one solution I would get something like this. www.banggood.com/LED-Lights-Controller-Electronic-Switch-2A-For-FPV-RC-Quadcopter-p-976106.html?rmmds=search
@jjeei7 жыл бұрын
Thank you for your answer. Do yo know other tipes leds for I don't need use it? like the picture: www.google.es/search?q=sp+racing+f3&source=lnms&tbm=isch&sa=X&ved=0ahUKEwilvL6KkPbQAhUJw1QKHdabDLUQ_AUICCgB&biw=1366&bih=638#imgrc=9E4az-dQYC5o_M%3A In this picture the led is with three cables (volt, ground and signal)
@neilyboy7 жыл бұрын
Jose G snag stone ws2812 or 2812B. many out there... here is one.. m.banggood.com/Diatone-WS2812-WS2812B-RGB-LED-Board-5050-For-Naze32-CC3D-p-1026673.html
@jjeei7 жыл бұрын
ohhh thank you !!
@zoopinc8 жыл бұрын
bad video
@neilyboy8 жыл бұрын
+zoop inc. Its not just bad its awful! I mean terrible..
@zoopinc8 жыл бұрын
neilyboy RIGHT, thank you 😉☺
@BaronCreel9 жыл бұрын
I did that to two today actually
@theshapeexists10 жыл бұрын
harbor freight is the best place to buy a shit tool that you only need for a quick project. i bought some knockoff dremel for $7 with like 30 attachments like 12 years ago and the thing miraculously still works.
@Deadlightsanctuary10 жыл бұрын
this thing fuckin sux!!! I tried cutting out a knife and it kept jumping and the grinding blade kept coming loos so it wouldn't cut. I got this shit for Christmas and though its a gift and im not gonna hurt the persons feelings by telling them because this person looked really excited they got it for me but NEVER I repeat NEVER by this thing for cutting purposes. fucked up my knifes handle and everything... my dads hand saw cut better then that thing and trust me I compared..
@1NFILTRATE11 жыл бұрын
Umad?
@iluv9mm111 жыл бұрын
Is that a polishing wheel, and is it larger than 4-1/2"? Quote from manual... Not sure why they say this, but could be that polishing loads the motor down more than a grinding wheel: "Operations such as polishing or cutting-off are not recommended to be performed with this power tool. Operations for which the power tool was not designed may create a hazard and cause personal injury."
@kennyc38811 жыл бұрын
In his 20's or whatever and he's already a mini slob loser.
@neilyboy11 жыл бұрын
It eats up a half a day or so by the time you get everything all cleaned up but the end result is worth it!
@stringfrenzy11 жыл бұрын
Looks like it was quite a day. Good video!
@TheGunnut9512 жыл бұрын
why did you brake it???
@Del-Canada12 жыл бұрын
Woooooooooooooooooooooo! Nice seeing you again man!
@neilyboy12 жыл бұрын
anything that comes with a re-build kit is quality ;) it was 9.99 I was able to build and polish a keggle with it so I got good use out of it...
@ncrdisabled12 жыл бұрын
Gee it comes with a warranty and it comes with a spare set of brushes and it looks like the brushes grounded out. I hope you can get replaced or fixed.
@neilyboy12 жыл бұрын
I have tried giving the driver 12v off an sla its dead...
@neilyboy12 жыл бұрын
Illinois
@Powdermonkey9912 жыл бұрын
sweet - what state are you hunting?
@etrac00712 жыл бұрын
congrats on the lc!
@westside1878512 жыл бұрын
the tail piece has a bad ground if u use some snap-ring pliers u can re-tighten it and it should work i had the same problem with on that i bought from dealxtreme to do this there r two small dimples near the threads on opposite sides of the spring just put the end of the pliers in the dimples and tighten it let me know if that works
@D3MAK14 жыл бұрын
use the stand on the multimeter ffs!!!
@lambition14 жыл бұрын
Li-Ion cells are 4.2V at full charge. So, what you are getting off the battery is correct voltage. You will read different voltage if it is under load. It appears the reason your battery did not work on your flash is because positive terminal of the battery is not sticking out by much as with AA battery. Put some solder blob (as bstrickler suggested) on positive contact point of the flash. that should fix your problem.
@bstrickler15 жыл бұрын
Where the positive terminal goes, is there a solder blob inside the flashlight? If not, theres your problem. I bought a Trustfire TR-801 (or 802) from them and the 18650 wouldn't work until I added a solder blob to the end of it. You can also try ordering one of their 6-8mm Neodymium magnets and putting that at the positive terminal of the battery. It should work then.
@neilyboy15 жыл бұрын
I can assure you I put the battery in correctly.. idiot.
@edMerican15 жыл бұрын
3.6v protected cells at full charge run 4.2 volts nominal. not sure why but thats the way it is and has laways been...
Пікірлер
i just got one the other day do you use wifi or the usb drive
Still watching this video 2 years later❤ hope we get it again this CREEKEND
Resigned with no leave notice angle grinder hhhh
Is this still a good 3d printer in 2022?
If you are able to scoop one up for cheap then yeah actually.. throw a few bucks at it (if you have some free time) and it's a very capable machine. That said you can snag an ender 3 for 99 bucks every now and then... It's honestly all relative to your location and what's available and what you want to put into it. Since this video I dumped 40 bucks into a direct drive end on an xvixo x3s and that I picked up for 60 bucks and it prints like a dream.. reviews on 3d printers are honestly a joke anymore... Years ago if you wanted out of the box ease of use these were about all you had... I believe Anker (the electronics go to on Amazon) has a Kickstarter for a printer that looks promising. Throw money towards it if your not in a hurry. To me that looks promising... 3d printing can be a headache if you are just starting out. That said once you have owned a few machines it's not uncommon to start a print on a machine leave for work and come home to a decent print now-a-days.. if you ask me my opinion anymore (I've owned over 30 printers in the past few years)... I have found that the ones you tinker with the most will always be your go to... I have built a couple hypercube based printers that I really loved.. I had a lot of time in them... I spent 60 bucks on your basic ender3 clone and put a different hot end on it and had excellent results... This reply probably does not help much but what I'm getting at is if you put some time into this guy yeah it's a very capable printer... Maybe snag one of these used and throw in a different board and your set....
@@neilhagan5566 Thanks for the reply
This still has me buzzing 💘
Could you tell how do I fix the touch panel is not on issue?
Ol Neilyboy.
Del how the heck have you been buddy!?
@@neilyboy Just spinning in the marrow and living life. I finally got one of your notifications. KZread is consistently busted. D'oh! I hope you are doing well. Been a long time. KK is still up and the channel is still around.
@@Del-Canada I should swing into the good ol irc. It's our anniversary so the wife and I are heading out for s night out tonight
How do you know he doesn't have a medical condition?
The ol Neilyboy.
Is the camera being powered by the panel?
I have a couple 12v 7ah lead acid batteries in a waterproof box down below. The panel could power the camera but it would only be available when the sun is out of course.
Is this Neilyboy from KK?
Delphinius! Sure is buddy how in the heck have you been!
@@neilyboy LMAO Just doing the internet rounds and thought about you for some reason. I think I dropped by several years ago also. Heh.
@@Del-Canada that's awesome! Oh the good ol days of the interwebs. Any crazy projects lately? I am thinking about building a virtual pinball cabinet for the kids to play around with.
@@neilyboy My legs were shot off back there in Okinawa.
@@Del-Canada don't need legs to play pinball
Was that ice water being recirculated through an immersion chiller and then through a CFC?? How long to cool? 3 mins???
It was fairly quick I could run directly from boil to fermentor and pitch shortly after
is this a good printer for a begginer?
Yeah. With its leveling features and filament options I think it's a great starter myself.
just ordered one should come in a week
Did you provide product presentation or product demo on the site?
No I have no affiliation with xyz
can anyone help me .... so purchase this same printer and i go and turn it on and the LED lights flashes and and the motor rides to the back of the wall and does this scraping sound .im just a beginner lol
@@M3LLYM3L69 any error number on screen? Where is the scraping noise coming from?
@@neilyboy no nothing on the screen ....the axis is going all the way to the back and the LED lights does not turn on just a quick flash
@@M3LLYM3L69 interesting. You don't happen to see any loose wires anywhere do you? It sounds like a hardware fault of some kind to me. You just unboxed this? Davinci has good support. Where did you purchase?
Just ordered the same unit. Should arrive in two days. Thanks for sharing your set-up video.
Good job
But when you posted this I lived in metamora
I live there :D
50 euro
That looks like the basement from the first Ghostbusters movie.
I used a piece of glass cut just inside of the 4 brackets. I also use elmers glue stick and apply 5 cross coats of the glue on the glass. Then I use aluminum tape on the sides of the glass to hold the glass in place. When you do this if you do..you are going to have to reset your Z offset and use a business card for your clearance of the nozzle to the glass plate. I adjusted mine to where the card slides smoothly under the nozzle with just a tad of a grab by the nozzle. Then when the print is done i remove the glass and let it sit for about 10 minutes...the part should pull off easy. then i rinse my glass plate and re do the process when i want to print something else.
The glue sticks are awful as adhesive. Try hairspray. Much easier to both apply and clean.
John Stratairious what type power supplies?
I shared your video on face book so hopefully you'll get some more HITS. thanks again for the video brother.
yeah i got the one with the laser the scanner and of course the 3d printer. unboxed mine today on april 27 2017. can't wait to use it. thanks for the video...it was good.
Hello, Do you know how turn on and turn off the leds from your control?
There may be alternate ways of doing this but if you wanted an all in one solution I would get something like this. www.banggood.com/LED-Lights-Controller-Electronic-Switch-2A-For-FPV-RC-Quadcopter-p-976106.html?rmmds=search
Thank you for your answer. Do yo know other tipes leds for I don't need use it? like the picture: www.google.es/search?q=sp+racing+f3&source=lnms&tbm=isch&sa=X&ved=0ahUKEwilvL6KkPbQAhUJw1QKHdabDLUQ_AUICCgB&biw=1366&bih=638#imgrc=9E4az-dQYC5o_M%3A In this picture the led is with three cables (volt, ground and signal)
Jose G snag stone ws2812 or 2812B. many out there... here is one.. m.banggood.com/Diatone-WS2812-WS2812B-RGB-LED-Board-5050-For-Naze32-CC3D-p-1026673.html
ohhh thank you !!
bad video
+zoop inc. Its not just bad its awful! I mean terrible..
neilyboy RIGHT, thank you 😉☺
I did that to two today actually
harbor freight is the best place to buy a shit tool that you only need for a quick project. i bought some knockoff dremel for $7 with like 30 attachments like 12 years ago and the thing miraculously still works.
this thing fuckin sux!!! I tried cutting out a knife and it kept jumping and the grinding blade kept coming loos so it wouldn't cut. I got this shit for Christmas and though its a gift and im not gonna hurt the persons feelings by telling them because this person looked really excited they got it for me but NEVER I repeat NEVER by this thing for cutting purposes. fucked up my knifes handle and everything... my dads hand saw cut better then that thing and trust me I compared..
Umad?
Is that a polishing wheel, and is it larger than 4-1/2"? Quote from manual... Not sure why they say this, but could be that polishing loads the motor down more than a grinding wheel: "Operations such as polishing or cutting-off are not recommended to be performed with this power tool. Operations for which the power tool was not designed may create a hazard and cause personal injury."
In his 20's or whatever and he's already a mini slob loser.
It eats up a half a day or so by the time you get everything all cleaned up but the end result is worth it!
Looks like it was quite a day. Good video!
why did you brake it???
Woooooooooooooooooooooo! Nice seeing you again man!
anything that comes with a re-build kit is quality ;) it was 9.99 I was able to build and polish a keggle with it so I got good use out of it...
Gee it comes with a warranty and it comes with a spare set of brushes and it looks like the brushes grounded out. I hope you can get replaced or fixed.
I have tried giving the driver 12v off an sla its dead...
Illinois
sweet - what state are you hunting?
congrats on the lc!
the tail piece has a bad ground if u use some snap-ring pliers u can re-tighten it and it should work i had the same problem with on that i bought from dealxtreme to do this there r two small dimples near the threads on opposite sides of the spring just put the end of the pliers in the dimples and tighten it let me know if that works
use the stand on the multimeter ffs!!!
Li-Ion cells are 4.2V at full charge. So, what you are getting off the battery is correct voltage. You will read different voltage if it is under load. It appears the reason your battery did not work on your flash is because positive terminal of the battery is not sticking out by much as with AA battery. Put some solder blob (as bstrickler suggested) on positive contact point of the flash. that should fix your problem.
Where the positive terminal goes, is there a solder blob inside the flashlight? If not, theres your problem. I bought a Trustfire TR-801 (or 802) from them and the 18650 wouldn't work until I added a solder blob to the end of it. You can also try ordering one of their 6-8mm Neodymium magnets and putting that at the positive terminal of the battery. It should work then.
I can assure you I put the battery in correctly.. idiot.
3.6v protected cells at full charge run 4.2 volts nominal. not sure why but thats the way it is and has laways been...