Repointing meant staking old mortar out and repoint it
@shenghan93852 жыл бұрын
🤣🤣🤣
@lachlanb22702 жыл бұрын
How do you get it so smooth without cleaning or wetting the trowel
@anireseegam61282 жыл бұрын
You couldn't match the colour?????
@jamsandwich61422 жыл бұрын
I love widge caps
@manchula9872 жыл бұрын
Hi Jack, could you replace my valley
@barrydoyle16883 жыл бұрын
Yeeee haw!! There's levels to this!!
@rosenchowdhury663 жыл бұрын
how much does it cost to replace a roof valley , thanks
@jacksmith43753 жыл бұрын
Cowboy
@jaimejaime38503 жыл бұрын
Did u repoint on top of the old existing bedding?
@dylangale5577 Жыл бұрын
If you can’t lift the ridge capping from the old bedding it will be ok to clean and repoint over the top. The old bedding is only cement with a oxide mixed through. If you can get away with just an “over point” it’s easier and more cost effective for the home owner
@zeckham1003 жыл бұрын
Ridges cleaned off hahaha they still have moss on them
@MrDigger450 Жыл бұрын
Anyone know easy way to get rid off that moss stuff??
@IamBlueDragon_ Жыл бұрын
@@MrDigger450 get a wire brush for your grinder. Did my entire roof in less than 2 hours. Also used a cup grinder disc to remove old pointing.
@moonchasestar3 жыл бұрын
thank you so much for your sharing.
@grahamhill94994 жыл бұрын
Nails thru the existing cap fron the new cap ,pure leak
@jayburton98784 жыл бұрын
Missing the hip iron aswell
@jonmcleary59004 жыл бұрын
Hey guys can you leave some more white marks on the rooftiles next time .lol.Crap work..
@jonmcleary59004 жыл бұрын
Shit work boys .
@artisansportsman89504 жыл бұрын
Absolute rubbish , I hope that was your house & not a paying customer .
@BlazingBigJointz5 жыл бұрын
Good evening Jack. If it's not too much trouble could you please let me know the approximate cost of such a job? I live in Melbourne so I'm a bit too far away from you, however any advice would be appreciated. I have an internal roof leak that is penetrating the roof cavity next to the valley area so I suspect there's a hole that I can't see from outside. Cheers!
@TheMatrixgod5 жыл бұрын
i have a aluminum boom attached to a steal pedestial,so can a zinc attached to the boom prevent the two metals from corrosion?
@baronbadtaste60605 жыл бұрын
Pretty rough work . Cowboy operator
@dylangale55772 жыл бұрын
Spastic he’s recording and pointing at the same time. This video isn’t on how to do it perfect it’s explaining to people the steps and reasons of bedding and pointing
@alexkoutinas94396 жыл бұрын
If you look in the bottom left hand corner of screen at 1.17 you can see Jesus face 😮 looking bemused at the state of that valley guuurrr yesus!
@michaelsoskan97076 жыл бұрын
messy as fuck
@robertcaswell39146 жыл бұрын
Did you point that up with your bellend
@jackharvey64527 жыл бұрын
So many people talking shit about a blokes work. Perhaps the reason he didn't strip and re bed all the hips is because the customer didn't want to pay for it. I'm a roof tiler, and if there customer doesn't want to spend the money well, they get a shit job
@jacksmith43753 жыл бұрын
And if they don’t wanna proper job walk away certainly don’t post yourself on internet doing shoddy things
@janlewis79297 жыл бұрын
That looks easy enough! Just need to conquer my fear of heights lol and find a cool enough day to get it done 😕
@anylength22158 жыл бұрын
About as useful as a hole in the head. Don't show us the finished stages! Tell us how you did it! Every step of the way.
@sp5030758 жыл бұрын
you might get a better photographer next time that can show what you are actually doing.
@boganindustries9 жыл бұрын
Good video. Was handy to demonstrate to my girlfriend what I was planning to do to stop our verandah leaks. Cheers.
@rodrigezgozalo47809 жыл бұрын
Jolly good show old chap,just hope your GAS SAFE working at that height.
@pilotanimal1929 жыл бұрын
stop calling them caps,
@francisbalfour43549 жыл бұрын
Thort you said it was terrachotta repaint then, was like. U got to be joking me, do t paint terrachottas -.- unless they don't know who you are, then go ahead hahahaha
@scottyp65599 жыл бұрын
Dude as soon as you put your second cap on your gonna make a leak!!!
@andybbrown875210 жыл бұрын
How do you get smooth look? Mine goes globby. Also, how about the weep outlets? As for the haters I think well, it's better to do than not do even if it isn't a really good job better than having exposed bedding and it's probably a good product at keeping the rain out.
@BettySwollocks1310 жыл бұрын
When you say pointing, you used you finger didn't you, you literally used a finger :D
@pauldulson665210 жыл бұрын
one word.CoWWWWWWWWWWWWW Boyyyyyyyyyyyyyyy.
@Benzknees11 жыл бұрын
If the new mortar is just applied as a thin layer onto old pointing, it'll crack and spall off in no time atall. You need to rake out the old mortar to form a key, assuming it is reasonably sound. If it's loose or badly cracked, then you'll need to completely remove it, possibly inc
@dgb582011 жыл бұрын
Great footage
@neiltreloar11 жыл бұрын
Cowboy! Take the ridges off and re-bed them using good 3&1 mortar.
@dylangale5577 Жыл бұрын
It’s all about explaining to home owners the process. Not everyone wants to rip people off with a full rebed and point mate. If you can’t physically remove the ridge from the old mortar it’s fine to clean and over point and mind you more cost effective and appealing to the home owner
@Vinnienega11 жыл бұрын
Your missing a cut on the bottom
@56DOBO12 жыл бұрын
was he on rogue traders...
@Starlight01212 жыл бұрын
@TheCrazyturnip "what do you mean rake out the motor?" I have similar situation on my roof here that require re-pointing. What i'm about to do it, rahter then using a wire brush I'm going to apply some anti-fungi detergent all around the crack area then high pressure clean using 3000 psi spray gun then do then apply the flexi-pointing . how's that sounf? hope it work.
@kyle212121 Жыл бұрын
So 11 years later. How’d it work out for you with the new re-point after detergent ?
@Starlight01212 жыл бұрын
I totally agree. Before criticizing have your instructional video upload please so i can have a look at learn from it too. There's plenty of talker out there and not many do' er. Criticizing others doesn't make you smarter you know. However criticizing with an expert feedback is does.However, I don't see any here. Thanks you for your video sir.
@Starlight01212 жыл бұрын
Thank for your time making and uploading these video. Although you instructions isn't 100% correct but at least 80% of them is.Your instruction is clear and precise and most of all youre using human language that i can understand. By watching your video I have gain a much clearer understanding on how to performance the job. Of course that there's always the needs to improve but that depends on how much time and money you're willing to spend. I just want a standard finish.
@OlegMykolajovychOlijnyk12 жыл бұрын
... а подстелить трудно было !? всю крышу раствором засрал!
@88601412 жыл бұрын
Thank you very much for putting these videos up. For those who can do nothing but criticise please post the links to the videos they have put up, then people can critique them too! I have never done this type of work before but am pretty good with my hands. Yes it takes me forever but the results are normally quite ok. Getting smooth troweling consistently is not as easy as it looks, but I'm quite confident that my roof will not leak on the ridge capping. Thanks again for posting.
@jjasonell12 жыл бұрын
ouch
@jjasonell12 жыл бұрын
ridem cowboy
@jjasonell12 жыл бұрын
ouch
@greenengineer512 жыл бұрын
very helpful, thanx mate. keep up the great work , and for the people who complain all the time just go aand get a pair of panties thats whats good for you
Пікірлер
Coving up corroding mortar clown
Repointing meant staking old mortar out and repoint it
🤣🤣🤣
How do you get it so smooth without cleaning or wetting the trowel
You couldn't match the colour?????
I love widge caps
Hi Jack, could you replace my valley
Yeeee haw!! There's levels to this!!
how much does it cost to replace a roof valley , thanks
Cowboy
Did u repoint on top of the old existing bedding?
If you can’t lift the ridge capping from the old bedding it will be ok to clean and repoint over the top. The old bedding is only cement with a oxide mixed through. If you can get away with just an “over point” it’s easier and more cost effective for the home owner
Ridges cleaned off hahaha they still have moss on them
Anyone know easy way to get rid off that moss stuff??
@@MrDigger450 get a wire brush for your grinder. Did my entire roof in less than 2 hours. Also used a cup grinder disc to remove old pointing.
thank you so much for your sharing.
Nails thru the existing cap fron the new cap ,pure leak
Missing the hip iron aswell
Hey guys can you leave some more white marks on the rooftiles next time .lol.Crap work..
Shit work boys .
Absolute rubbish , I hope that was your house & not a paying customer .
Good evening Jack. If it's not too much trouble could you please let me know the approximate cost of such a job? I live in Melbourne so I'm a bit too far away from you, however any advice would be appreciated. I have an internal roof leak that is penetrating the roof cavity next to the valley area so I suspect there's a hole that I can't see from outside. Cheers!
i have a aluminum boom attached to a steal pedestial,so can a zinc attached to the boom prevent the two metals from corrosion?
Pretty rough work . Cowboy operator
Spastic he’s recording and pointing at the same time. This video isn’t on how to do it perfect it’s explaining to people the steps and reasons of bedding and pointing
If you look in the bottom left hand corner of screen at 1.17 you can see Jesus face 😮 looking bemused at the state of that valley guuurrr yesus!
messy as fuck
Did you point that up with your bellend
So many people talking shit about a blokes work. Perhaps the reason he didn't strip and re bed all the hips is because the customer didn't want to pay for it. I'm a roof tiler, and if there customer doesn't want to spend the money well, they get a shit job
And if they don’t wanna proper job walk away certainly don’t post yourself on internet doing shoddy things
That looks easy enough! Just need to conquer my fear of heights lol and find a cool enough day to get it done 😕
About as useful as a hole in the head. Don't show us the finished stages! Tell us how you did it! Every step of the way.
you might get a better photographer next time that can show what you are actually doing.
Good video. Was handy to demonstrate to my girlfriend what I was planning to do to stop our verandah leaks. Cheers.
Jolly good show old chap,just hope your GAS SAFE working at that height.
stop calling them caps,
Thort you said it was terrachotta repaint then, was like. U got to be joking me, do t paint terrachottas -.- unless they don't know who you are, then go ahead hahahaha
Dude as soon as you put your second cap on your gonna make a leak!!!
How do you get smooth look? Mine goes globby. Also, how about the weep outlets? As for the haters I think well, it's better to do than not do even if it isn't a really good job better than having exposed bedding and it's probably a good product at keeping the rain out.
When you say pointing, you used you finger didn't you, you literally used a finger :D
one word.CoWWWWWWWWWWWWW Boyyyyyyyyyyyyyyy.
If the new mortar is just applied as a thin layer onto old pointing, it'll crack and spall off in no time atall. You need to rake out the old mortar to form a key, assuming it is reasonably sound. If it's loose or badly cracked, then you'll need to completely remove it, possibly inc
Great footage
Cowboy! Take the ridges off and re-bed them using good 3&1 mortar.
It’s all about explaining to home owners the process. Not everyone wants to rip people off with a full rebed and point mate. If you can’t physically remove the ridge from the old mortar it’s fine to clean and over point and mind you more cost effective and appealing to the home owner
Your missing a cut on the bottom
was he on rogue traders...
@TheCrazyturnip "what do you mean rake out the motor?" I have similar situation on my roof here that require re-pointing. What i'm about to do it, rahter then using a wire brush I'm going to apply some anti-fungi detergent all around the crack area then high pressure clean using 3000 psi spray gun then do then apply the flexi-pointing . how's that sounf? hope it work.
So 11 years later. How’d it work out for you with the new re-point after detergent ?
I totally agree. Before criticizing have your instructional video upload please so i can have a look at learn from it too. There's plenty of talker out there and not many do' er. Criticizing others doesn't make you smarter you know. However criticizing with an expert feedback is does.However, I don't see any here. Thanks you for your video sir.
Thank for your time making and uploading these video. Although you instructions isn't 100% correct but at least 80% of them is.Your instruction is clear and precise and most of all youre using human language that i can understand. By watching your video I have gain a much clearer understanding on how to performance the job. Of course that there's always the needs to improve but that depends on how much time and money you're willing to spend. I just want a standard finish.
... а подстелить трудно было !? всю крышу раствором засрал!
Thank you very much for putting these videos up. For those who can do nothing but criticise please post the links to the videos they have put up, then people can critique them too! I have never done this type of work before but am pretty good with my hands. Yes it takes me forever but the results are normally quite ok. Getting smooth troweling consistently is not as easy as it looks, but I'm quite confident that my roof will not leak on the ridge capping. Thanks again for posting.
ouch
ridem cowboy
ouch
very helpful, thanx mate. keep up the great work , and for the people who complain all the time just go aand get a pair of panties thats whats good for you