What's the torque specs for the tie rods? Great videos. I am a follower.
@TTKOFFICIALCHANNEL9 күн бұрын
I really appreciate what you doing here.
@brandon3337110 күн бұрын
Tf was the tip mf it says in the manual to replace it anyway
@Nprdoctor10 күн бұрын
DIY mechanics watching these videos may be tempted to reuse them because of how expensive they are. Trying to save the next man or woman some trouble is all.
@hughhowes897211 күн бұрын
Thank you for this video, it was very helpful. Can you do one for the AC belt as well? Thank you
@geoffap013 күн бұрын
Thank you again for your time and talent and making this video! I hope you come back to this channel and make more!
@geoffap013 күн бұрын
I appreciate your time and talent making these videos. I hope you do more!
@circlecfarm15 күн бұрын
Hey, @NPR Doctor! How can we reach you to maybe ask a few questions? Or better yet - I'd love to see a vicdeo about TIRE PRESSURES AND TEMPERATURES. I'm noticing on my NRR with largely an empty box, that I can get 20-30 degree higher temps in the rear passenger INSIDE tire, and maybe 10-20 on the rear outside. Any reapson for this, exhaust maybe? Road crown? Or is there an issue I need to watch out for?
@jeftkuan16 күн бұрын
simple &easy to understanding👍👍thank of sharering !it really help alot💯
@Renegar8724 күн бұрын
Great video
@georgeg717225 күн бұрын
Do you have a radiator coolant flush video? Thanks a million!
@pedroalarcon9394Ай бұрын
Great video! Can you do some videos on replacing the front & rear brakes on an NPR?
@jessesoto7098Ай бұрын
How do I fix the Cargo light inside the box? My inside light switch does not illuminate with red dot when its on?
@JonStackАй бұрын
I really appreciate your videos, thank you.
@Tealdog038Ай бұрын
Do you torque the stud's to 362ft/lbs also?
@ghosteroven9718Ай бұрын
Is there a cable for the fresh/recycled air?
@geoffap0Ай бұрын
The bottom 22mm caliper bolt is a pain to torque. I had to cut a socket down to fit. I’m curious what you used. Thanks for making this video.
@Barren_Harem8085 күн бұрын
Understand what you mean, I had issues of the first side because I had the steering pretty close to lock, trying to get the most room. On the second side I found a sweet angle where the socket cleared that lower steering knuckle, and the other three bolts were accessible as well.
@karelirodriguez499Ай бұрын
Thank you!!!
@asingh7545Ай бұрын
hey bro i like your repair videos just wanted to ask if you know the glow plug torque spec on a 4he1 isuzu engine.
@VinmoranoАй бұрын
Have you considered a video doing glow plugs? Maybe on a 07-09 4hk1 =p I’ve searched and there is one decent video but he doesn’t mention torque specs and I can’t find that info anywhere online. Thanks :)
@grum7140Ай бұрын
Thanks for the video. Was trying to find the power steering fluid reservoir and your video helped a lot. Ended up being below the AC so it’s almost impossible to check. Still though, without your video I don’t know if I ever would have found it
@anthonyleesmann9863Ай бұрын
Just in case i missed your answer. On drivers side that is reverse thread. Once outer lug nut is removed, will the inner stud that 21mm socket is used on be reverse thread as well. Thanks
@dannysandoval82962 ай бұрын
are these tire rods enough to make this truck shake like crazy when they go bad? almost feels like the damn tire is about to go flying
@MOHDALOWEIDI-sw8go2 ай бұрын
Do you know how much an engine overhaul cost on a 2016 NQR 5.2L 4 cylinder diesel engine ? And who is the best to do the job ?
@patrickshaw85952 ай бұрын
Glad I found this !!! I just used a 50 ton gear puller on my inner duals and it's jaws ripped small pieces out of the wheel holes! I said "C'mon Man! Something has to be holding this thing on!" I get it - you unscrew the WHEEL STUDS !!! (and there are smaller fixed studs inside those)
@jeffreywooten1782 ай бұрын
If your truck cuts off when you put it in gear, what do you do?
@jeffreywooten1782 ай бұрын
Need your help
@stevenbund66412 ай бұрын
Do you have a video off changing the shoes
@wescrichton42642 ай бұрын
Thanks for the video, what do you torque the 8x nuts to that hold the rear side shafts in?
@Vinmorano2 ай бұрын
Hey Doc, you know if the wheel bearing info you give in this video is the same for an 09?
@sukhdeepcheema12212 ай бұрын
Thnakew so much
@woodFTP2 ай бұрын
Hey man I love your vids! I learned how to do brakes and adjust the parking and rears because of you. I just recently changed the front calipers on a 2016 and I am unsure of the bleeding procedure. I have the IDSS software but I am not sure if I need the truck running or not. I read a lot of different info on the web. How do you bleed brakes on the npr?
@LilReaper10102 ай бұрын
THANK YOU FOR THE VIDEO!!
@LilReaper10102 ай бұрын
Wow these look like the old school hotel HVAC unit filters too!😂
@user-oy6ju3hm3z2 ай бұрын
What causes the control to jam up? Mine is not knob is not broken but will not go to defrost.
@dustywilson54612 ай бұрын
Thnx
@KevLb4LB2 ай бұрын
Hry NPR Doctor when you can can you perform a power steering flush on a crew cab npr hd 2015-2020. Thanks man have a good one.
@jimparrie97082 ай бұрын
I find that jacking the axel up an inch or so to take the weight off the wheel allows a more uniform flow of grease into the bottom king pin fitting and around the bottom thrust washers.
@AnthonyValerio-wc6dh3 ай бұрын
Thanks for the good vids. What's torque spec for the axle flange bolts?
@josephburdette94773 ай бұрын
Do you find this to be a common issue for the front end death wobble on NPRs?
@georgeg71723 ай бұрын
Hi, Question: you mentioned to invest in a torch to help get these stubborn Lugnuts off. Not exactly sure what torch and how I would use it. Could you recommend a model number of an appropriate torch? And do I just heat up the stud in the middle of the nut or heat the outside of the nut as well? What I like about Your videos is that you give step by step instruction(even the steps that might be considered common sense to some). Thanks
@gordonretherford54513 ай бұрын
Thank you!
@gordonretherford54513 ай бұрын
thank you
@GHIDRAuto3 ай бұрын
Ecu reverse engineering. How to find EGT, MAF, ECT, And more sensor scalers. Denso sh7058 kzread.info/dash/bejne/nIajk9mrZ9KeYMo.html
@gordonretherford54513 ай бұрын
Thank you.
@richardauger96953 ай бұрын
You can access the filter under that panel, no need to take panel off.
@zerihunderbe33733 ай бұрын
Thanks
@zerihunderbe33733 ай бұрын
Thanks
@tookey22493 ай бұрын
Please make more videos on this Isuzu NPR 6.0 V8 truck!! Super helpful content doc
@praveenshah24713 ай бұрын
Hi brother I have 2015 npr hd gas truck The cabin is shaking when I m applying the Breaks , what’s is the reason for this
Пікірлер
Safety squints
What's the torque specs for the tie rods? Great videos. I am a follower.
I really appreciate what you doing here.
Tf was the tip mf it says in the manual to replace it anyway
DIY mechanics watching these videos may be tempted to reuse them because of how expensive they are. Trying to save the next man or woman some trouble is all.
Thank you for this video, it was very helpful. Can you do one for the AC belt as well? Thank you
Thank you again for your time and talent and making this video! I hope you come back to this channel and make more!
I appreciate your time and talent making these videos. I hope you do more!
Hey, @NPR Doctor! How can we reach you to maybe ask a few questions? Or better yet - I'd love to see a vicdeo about TIRE PRESSURES AND TEMPERATURES. I'm noticing on my NRR with largely an empty box, that I can get 20-30 degree higher temps in the rear passenger INSIDE tire, and maybe 10-20 on the rear outside. Any reapson for this, exhaust maybe? Road crown? Or is there an issue I need to watch out for?
simple &easy to understanding👍👍thank of sharering !it really help alot💯
Great video
Do you have a radiator coolant flush video? Thanks a million!
Great video! Can you do some videos on replacing the front & rear brakes on an NPR?
How do I fix the Cargo light inside the box? My inside light switch does not illuminate with red dot when its on?
I really appreciate your videos, thank you.
Do you torque the stud's to 362ft/lbs also?
Is there a cable for the fresh/recycled air?
The bottom 22mm caliper bolt is a pain to torque. I had to cut a socket down to fit. I’m curious what you used. Thanks for making this video.
Understand what you mean, I had issues of the first side because I had the steering pretty close to lock, trying to get the most room. On the second side I found a sweet angle where the socket cleared that lower steering knuckle, and the other three bolts were accessible as well.
Thank you!!!
hey bro i like your repair videos just wanted to ask if you know the glow plug torque spec on a 4he1 isuzu engine.
Have you considered a video doing glow plugs? Maybe on a 07-09 4hk1 =p I’ve searched and there is one decent video but he doesn’t mention torque specs and I can’t find that info anywhere online. Thanks :)
Thanks for the video. Was trying to find the power steering fluid reservoir and your video helped a lot. Ended up being below the AC so it’s almost impossible to check. Still though, without your video I don’t know if I ever would have found it
Just in case i missed your answer. On drivers side that is reverse thread. Once outer lug nut is removed, will the inner stud that 21mm socket is used on be reverse thread as well. Thanks
are these tire rods enough to make this truck shake like crazy when they go bad? almost feels like the damn tire is about to go flying
Do you know how much an engine overhaul cost on a 2016 NQR 5.2L 4 cylinder diesel engine ? And who is the best to do the job ?
Glad I found this !!! I just used a 50 ton gear puller on my inner duals and it's jaws ripped small pieces out of the wheel holes! I said "C'mon Man! Something has to be holding this thing on!" I get it - you unscrew the WHEEL STUDS !!! (and there are smaller fixed studs inside those)
If your truck cuts off when you put it in gear, what do you do?
Need your help
Do you have a video off changing the shoes
Thanks for the video, what do you torque the 8x nuts to that hold the rear side shafts in?
Hey Doc, you know if the wheel bearing info you give in this video is the same for an 09?
Thnakew so much
Hey man I love your vids! I learned how to do brakes and adjust the parking and rears because of you. I just recently changed the front calipers on a 2016 and I am unsure of the bleeding procedure. I have the IDSS software but I am not sure if I need the truck running or not. I read a lot of different info on the web. How do you bleed brakes on the npr?
THANK YOU FOR THE VIDEO!!
Wow these look like the old school hotel HVAC unit filters too!😂
What causes the control to jam up? Mine is not knob is not broken but will not go to defrost.
Thnx
Hry NPR Doctor when you can can you perform a power steering flush on a crew cab npr hd 2015-2020. Thanks man have a good one.
I find that jacking the axel up an inch or so to take the weight off the wheel allows a more uniform flow of grease into the bottom king pin fitting and around the bottom thrust washers.
Thanks for the good vids. What's torque spec for the axle flange bolts?
Do you find this to be a common issue for the front end death wobble on NPRs?
Hi, Question: you mentioned to invest in a torch to help get these stubborn Lugnuts off. Not exactly sure what torch and how I would use it. Could you recommend a model number of an appropriate torch? And do I just heat up the stud in the middle of the nut or heat the outside of the nut as well? What I like about Your videos is that you give step by step instruction(even the steps that might be considered common sense to some). Thanks
Thank you!
thank you
Ecu reverse engineering. How to find EGT, MAF, ECT, And more sensor scalers. Denso sh7058 kzread.info/dash/bejne/nIajk9mrZ9KeYMo.html
Thank you.
You can access the filter under that panel, no need to take panel off.
Thanks
Thanks
Please make more videos on this Isuzu NPR 6.0 V8 truck!! Super helpful content doc
Hi brother I have 2015 npr hd gas truck The cabin is shaking when I m applying the Breaks , what’s is the reason for this