Thanks for a well paced and presented video. Really useful information on how you approached measuring and maintaining the correct geometry
@blasvilca4696Ай бұрын
de verdad el chuk solo esta colocado a presion??? no lo creo....
Ай бұрын
how much for this, i want to buy one
Ай бұрын
Plesase contact my
@nowar92202 ай бұрын
For the dumbos crying you need a mill to make a cnc machine 😂😂 Wtf u think he was gonna sand some wood down n wack toogether a precision robotic machine!? 😂😂😂 Yes, what a suprise! To make precision machines you need precision parts..
@vinee6162 ай бұрын
downtown mafia 😄
@bensonlicayan512 ай бұрын
How can i order this machine?
@user-nw4dp8if2u3 ай бұрын
Hi Mr. Vincent... Because I want stay free man :) not bank slave ( Haas is so expensive :( ) My question for You is: On this machine is possible achieve 0,005 mm (or less) on 500 mm distance ? Ps. Good Job Vincent, and all best for YOU :) Im just starting design machine similar like Haas TM2P for steel and about 3000 kg weight, witch chip conveyor, and 20 ps. tool warehouse...
@utubepro77424 ай бұрын
Right Where you get stand?
@rotormotored4 ай бұрын
Hi, Vince. Do you know where I can get a straight edge like yours? I'm trying to rebuild my Bridgeport and my Southbend.
@avt-CNC4 ай бұрын
Почему сразу серво двигатели не поставили?? шаговый мотор с энкодером все равно остается шаговым мотором, и один из главных его минусов это резонанс потом падение крутящего момента!
@avt-CNC4 ай бұрын
Погрузите трубку слива в жидкость что бы при остановке в систему воздух не попадал!
@juansalgado62125 ай бұрын
would as 50/50 motor antifreeze work as well? would it need to diluted. The properties of, from my research, or coolant antifreeze for motors is different from the antifreeze of marine/rv pink antifreeze (pure antifreeze).
@TheHalloweenmasks5 ай бұрын
I don't know if you got your issue sorted out with z going to home position. If you didn't, try this. In fusion 360 CAM, in the post processer part there is a box for "safe retract" make sure this this is not set to G28 and to clearance height. Hope this helps.
@artwalker88125 ай бұрын
OMG... Standard rule for chatter, increase feed, decrease speed..
@majesticdragonfly5 ай бұрын
what cnc mill do you use for that ?
@user-hh1so1dy3y5 ай бұрын
How many Newtons is the torque?
@ianmoone23596 ай бұрын
I suspect from having watched Kieth Rucker & Steve Watkins do this same process that you may have “chased your tail” a bit, due to not using precision flat stones to remove your power scraping burrs before blue printing your scraped surface each time. It’s a lot more work scraping if your blue printing result is being influenced by burrs that protrude above the surface and influence the pattern you achieve. Whilst milling it flat at the start does save time, you might have saved a lot more time if you had precision ground the surfaces after milling. I think with pre vision grinding after milling, then employing precision ground flat stones to remove your scraping burrs you could have cut down the scraping time by factor of 10 probably.
@hakimbaqal6 ай бұрын
How long do I have to wait for my tree to grow harmonic drive?
@levanle6536 ай бұрын
Facile lorsqu'on est déjà visiblement très bien équipé !! N'importe quoi ! C'est le DIY avec Fraiseuse, Tour, rectifieuse, etc etc !! le DIY du riche :-)) !
@chrisleech15656 ай бұрын
BT30 spindle taper? I am guessing that the ATC spindle you have has a top RPM of 18000. Which means it has plenty of torque at much lower speed than generic 2.2kW spindles. Are you happy with it? Can you share where you got it? Satisfied with the runout? There is so much more choice in BT or ISO 30
@mojaveri6 ай бұрын
Very interesting video, thanks so much Would you mind sharing a bit more about the dial indicator stand you have? I am building one myself and your model looks very neat 😊
@johnbkyak7 ай бұрын
ya don't need the distracting "music"
@davidmuller19587 ай бұрын
Hey there what is the tool used to mark ways with blue color?
@maksuelmomelo91757 ай бұрын
maravilha de Projeto CNC
@ekbiker7 ай бұрын
Great job! I saw you indicating rail to rail parallelism. Just curious, how do you know that both rails are not slightly bowed?
@solomoncraftwood11807 ай бұрын
you need a milling machine for build a milling mashine. hmmmm...
@ZhouJing-jv5pe7 ай бұрын
Hello boss, I am a developer and manufacturer of CNC controllers. I mainly develop CNC engraving machines and milling machining centers. I am from Tianjin, China. If you need us, we can cooperate. You can leave your contact information and I will contact you. Sincere regards, Zhou Zhou
@ThomasLe_G8 ай бұрын
awesome but where do you find those big square metal tube ??
@farhanchoudhre69628 ай бұрын
Whats your z axis travel from table nose
@miladinseratlic59849 ай бұрын
Quite "easy" to build when you already have such machines to flatten, drill, mill parts...
@tattoosbyjoe2169 ай бұрын
Great video
@joneilarizala37379 ай бұрын
i dont understand why would you need 4 jaws chuck when you can already control your z axis.
@TomsDIYShop9 ай бұрын
Nice! Very clean build and looks AWESOME!
@akka475110 ай бұрын
Hello! Thanks for showing us your great results! Did you tried this spindle on steel? I would like to know your opinion before buying 😊
@williamjawbone338510 ай бұрын
Wow thats something to he proud of being able to do for sure
@NERVESxxOFxxSTEEL10 ай бұрын
Nobody mentions how to home the rotary axis especially when you use tombstone or sqaure stock. Do people just use dial indicator to square a flat surface? I see no proximity sensor.
@ScottHamilton-ys2cm10 ай бұрын
So many people focus on the task of scraping, and not how you to check the geometry of the machine, and the progress of the work, which is the most critical part of scraping. You did an excellent job of emphasizing that. I've been scraping for over 40 years, and teaching machine tool alignment and fit (scraping) for the last ten. I must say, your methods are unique, but quite effective. Keep up the good work.
@hamzaahsan57745 ай бұрын
good job. After scraping how to hard coat slides plz guide.
@rameshkp786011 ай бұрын
Super technology, thank you so much.
@thetwat811511 ай бұрын
I am trying to build almost similar as this one, will nema25 be okay, or i need nema35 steppers like yours?
@shawnbillock896811 ай бұрын
Appreciate and love the work...however, I am not sure you can really call it a DIY when you have a mill...to build a mill!
@brandontscheschlog11 ай бұрын
Very cool! Why didn’t you use the 45° angle on your camelback to check the dovetails of the column?
@dt909411 ай бұрын
Excellent job. All we need ,more people like you. It’s great thanks 🇨🇦👍
@dumitrutocila5807 Жыл бұрын
Realizare de calitate superioara 👏👏👏👏👍👍
@pcboreland1 Жыл бұрын
What linear bearings and ball screws did you use? What spec?
@kevinwhitcomb4495 Жыл бұрын
It's been a few years now, how did this build work out?
@carlosmenard3926 Жыл бұрын
Exelente
@capthowdy126 Жыл бұрын
was that lead that u melted down to fill the part?
@dm8198471640 Жыл бұрын
How is the trailer jack holding up? I’m asking as it is working the opposite way it is made for. It is suppose to be pushing up the weight but in your installation it is pulling up and holding. I’m just about to make one would love to hear from you. Thanks
@tray226 ай бұрын
I was going to ask the same and suggest he put a pin through it when it is in its higher position, then take the load off the lift mechanism. It isn't designed for bumps on the road or for lifting weight.
Пікірлер
Very nice build.
How many bottles of MAP gas did you go through?
Thanks for a well paced and presented video. Really useful information on how you approached measuring and maintaining the correct geometry
de verdad el chuk solo esta colocado a presion??? no lo creo....
how much for this, i want to buy one
Plesase contact my
For the dumbos crying you need a mill to make a cnc machine 😂😂 Wtf u think he was gonna sand some wood down n wack toogether a precision robotic machine!? 😂😂😂 Yes, what a suprise! To make precision machines you need precision parts..
downtown mafia 😄
How can i order this machine?
Hi Mr. Vincent... Because I want stay free man :) not bank slave ( Haas is so expensive :( ) My question for You is: On this machine is possible achieve 0,005 mm (or less) on 500 mm distance ? Ps. Good Job Vincent, and all best for YOU :) Im just starting design machine similar like Haas TM2P for steel and about 3000 kg weight, witch chip conveyor, and 20 ps. tool warehouse...
Right Where you get stand?
Hi, Vince. Do you know where I can get a straight edge like yours? I'm trying to rebuild my Bridgeport and my Southbend.
Почему сразу серво двигатели не поставили?? шаговый мотор с энкодером все равно остается шаговым мотором, и один из главных его минусов это резонанс потом падение крутящего момента!
Погрузите трубку слива в жидкость что бы при остановке в систему воздух не попадал!
would as 50/50 motor antifreeze work as well? would it need to diluted. The properties of, from my research, or coolant antifreeze for motors is different from the antifreeze of marine/rv pink antifreeze (pure antifreeze).
I don't know if you got your issue sorted out with z going to home position. If you didn't, try this. In fusion 360 CAM, in the post processer part there is a box for "safe retract" make sure this this is not set to G28 and to clearance height. Hope this helps.
OMG... Standard rule for chatter, increase feed, decrease speed..
what cnc mill do you use for that ?
How many Newtons is the torque?
I suspect from having watched Kieth Rucker & Steve Watkins do this same process that you may have “chased your tail” a bit, due to not using precision flat stones to remove your power scraping burrs before blue printing your scraped surface each time. It’s a lot more work scraping if your blue printing result is being influenced by burrs that protrude above the surface and influence the pattern you achieve. Whilst milling it flat at the start does save time, you might have saved a lot more time if you had precision ground the surfaces after milling. I think with pre vision grinding after milling, then employing precision ground flat stones to remove your scraping burrs you could have cut down the scraping time by factor of 10 probably.
How long do I have to wait for my tree to grow harmonic drive?
Facile lorsqu'on est déjà visiblement très bien équipé !! N'importe quoi ! C'est le DIY avec Fraiseuse, Tour, rectifieuse, etc etc !! le DIY du riche :-)) !
BT30 spindle taper? I am guessing that the ATC spindle you have has a top RPM of 18000. Which means it has plenty of torque at much lower speed than generic 2.2kW spindles. Are you happy with it? Can you share where you got it? Satisfied with the runout? There is so much more choice in BT or ISO 30
Very interesting video, thanks so much Would you mind sharing a bit more about the dial indicator stand you have? I am building one myself and your model looks very neat 😊
ya don't need the distracting "music"
Hey there what is the tool used to mark ways with blue color?
maravilha de Projeto CNC
Great job! I saw you indicating rail to rail parallelism. Just curious, how do you know that both rails are not slightly bowed?
you need a milling machine for build a milling mashine. hmmmm...
Hello boss, I am a developer and manufacturer of CNC controllers. I mainly develop CNC engraving machines and milling machining centers. I am from Tianjin, China. If you need us, we can cooperate. You can leave your contact information and I will contact you. Sincere regards, Zhou Zhou
awesome but where do you find those big square metal tube ??
Whats your z axis travel from table nose
Quite "easy" to build when you already have such machines to flatten, drill, mill parts...
Great video
i dont understand why would you need 4 jaws chuck when you can already control your z axis.
Nice! Very clean build and looks AWESOME!
Hello! Thanks for showing us your great results! Did you tried this spindle on steel? I would like to know your opinion before buying 😊
Wow thats something to he proud of being able to do for sure
Nobody mentions how to home the rotary axis especially when you use tombstone or sqaure stock. Do people just use dial indicator to square a flat surface? I see no proximity sensor.
So many people focus on the task of scraping, and not how you to check the geometry of the machine, and the progress of the work, which is the most critical part of scraping. You did an excellent job of emphasizing that. I've been scraping for over 40 years, and teaching machine tool alignment and fit (scraping) for the last ten. I must say, your methods are unique, but quite effective. Keep up the good work.
good job. After scraping how to hard coat slides plz guide.
Super technology, thank you so much.
I am trying to build almost similar as this one, will nema25 be okay, or i need nema35 steppers like yours?
Appreciate and love the work...however, I am not sure you can really call it a DIY when you have a mill...to build a mill!
Very cool! Why didn’t you use the 45° angle on your camelback to check the dovetails of the column?
Excellent job. All we need ,more people like you. It’s great thanks 🇨🇦👍
Realizare de calitate superioara 👏👏👏👏👍👍
What linear bearings and ball screws did you use? What spec?
It's been a few years now, how did this build work out?
Exelente
was that lead that u melted down to fill the part?
How is the trailer jack holding up? I’m asking as it is working the opposite way it is made for. It is suppose to be pushing up the weight but in your installation it is pulling up and holding. I’m just about to make one would love to hear from you. Thanks
I was going to ask the same and suggest he put a pin through it when it is in its higher position, then take the load off the lift mechanism. It isn't designed for bumps on the road or for lifting weight.