Пікірлер

• 
  @Jen-fy3pj16 күн бұрын

  At least it's fixed.

• 
  @stevegarrett102016 күн бұрын

  Not one of the most pleasant jobs.

• 
  @Retiredkiwi29 күн бұрын

  re SN1 or SN2, according to manuals with my units(smaller print at end of manual), SN1 is the default, and is used for either having only 1 magnet on fan wheel or having 2 magnets of the same polarity facing sensor(all 4 of mine have 2 magnets and use the SN1 default setting), SN2 is also for 2 magnets, but with different polarities(ie 1 is north pole facing sensor and second magnet is south pole facing sensor). To fit a local (heatport voice multi controller) stop/restart temperature controller to one of mine(speaks what its doing when buttons pressed or for faults etc), i had a clearance issue with magnets hitting sensor, (new motor board supplied/needed as well) but found a mention somewhere, that they often can be pressed deeper into their holes, which fixed my problem. i run my other 2 (4th one is a spare) units at 1.5/8hz and 1500/5000rpm "AT SEA LEVEL" with no airflow restrictions, in my back porch(22ml pumps), and have never had a sooting up or smoking issue with them (4 and 5 years old now). One (claimed) 8kw one came with those settings, 2 other claimed 5kw ones came set to 5 or 5.5hz max originally, and last one bought came set to 1.4 / 7hz 1500 / 4500 rpm, so they vary a lot, but all are otherwise identical units in every way(white alloy case versions with chrome end cap). At 8hz setting, they all drink 0.5lts per hour at max output, but usually a bit less, as they throttle back via housing temp sensor unless porch is still very cold(which means no more than 4.5kw's as that's all the available energy in that amount of fuel. Lower settings will be proportionally less output than that (not checked, but guessing only around 3kw's at 5 hz). 8hz output confirmed also by my calcs(4.2kw) of delta t and airflow when i first got them. Just ordered another one today, will be curious what its supplied settings are (i like the price drop over the years, first ones were $355nz, latest just $230 nz delivered I did try one on a 28ml pump for while, but could never get it to run clean throughout output range, so gave up on it. One issue i have had with recent ones, is supplied black ducting is not up to handling maximum heat, and stinks when hot, with paint slowly baking off and losing its colour.

• 
  @simplyboating460927 күн бұрын

  Great explanation.

• 
  @powdee11Ай бұрын

  Great video! The manual isn’t very helpful, I have a question, mine has H1-6 instead of the temp,what does that mean? I can’t change the temp at all

• 
  @simplyboating460929 күн бұрын

  H1 to H6 is a temp setting as well you should be able to change it by holding to top left button, then it should go to celsius instead.

• 
  @daddy-do-deez2 ай бұрын

  Thanks! Very informative. I’m running mine on propane and changing these settings helps a lot.

• 
  @kierenalvarez3 ай бұрын

  Won't do anything. When pressing the setting 3times. Must have changed it

• 
  @simplyboating46093 ай бұрын

  What are you trying to do ?

• 
  @user-bg4lm4hn9c3 ай бұрын

  Thank God 🙏 A man knows what his talking about & explains thoroughly ✊✔️👍

• 
  @simplyboating46093 ай бұрын

  Glad it was helpful.

• 
  @philophil19614 ай бұрын

  Do you know, is possible to use heater only as fan? In summer, for air circulation and cooling. Thank you.

• 
  @simplyboating46094 ай бұрын

  Not with the cheap Chinese models, it is possible with some of the more expensive models.

• 
  @mikepell93264 ай бұрын

  Really handy settings if you've got a smaller van, lower the pulse rate and the rpm and it'll run a little cooler so you don't need to keep turning it on and off again

• 
  @simplyboating46093 ай бұрын

  You can change it to automatically go up and down by pressing and holding the top left button

• 
  @keithfletcher63584 ай бұрын

  thanks for brilliant vid just bought one, the so called instruction manual from H calory is useless this video as really helped me out all the best keith.

• 
  @simplyboating46094 ай бұрын

  Thank you for watching Keith, I’m glad it was helpful.

• 
  @crazycrab85785 ай бұрын

  mine was on 1.7, went into settings, it would only go down to 1.6, put revs up to 1800, wonted to get the hz lower,

• 
  @autojohn-pu1vf5 ай бұрын

  mine will turn all the way down to 0.8, but when you exit out of settings it only turns down to 1.7 hz as before and no change in pulse rate.... it clicks 102 times a min(drink,drink,drink,drink,) Trying to use less fuel it gets way hot enough. I also have a HCCAL w alpine mode I cant' get on, different controller but it clicks 132 X min(drink,drink,drink,drink,)on all the way low setting

• 
  @simplyboating46095 ай бұрын

  Have you tried what autojohn suggested ?

• 
  @user-fp5pw3cv8s5 ай бұрын

  None of the codes work how would I find the code for my heater to get into settings

• 
  @simplyboating46095 ай бұрын

  I have never come across a different code 1688 is the only one i know of. Is it doing all the rest like pairing with your remote ? If not it maybe the CPU.

• 
  @Retiredkiwi29 күн бұрын

  i have read some are 9009, not seen any myself though.(also i spotted 888 for some with only 3 digits)

• 
  @patchitagain73736 ай бұрын

  How do you change the temperature reading from Celsius to Fahrenheit ??

• 
  @simplyboating46096 ай бұрын

  With this one this is not an option. There are some that you can and as you change from hz to Celsius it gives you that option to go to Fahrenheit.

• 
  @DEVONLAD116 ай бұрын

  I have the black board on my 2019 diesel heater. The newer blue boards work completely different to the older boards. There's no altitude adjustment plus you cant disable the pass code also the startup fan and pump control runs different and there's no startup retry ect. The blue board is a cheaper version of the old black one plus you cant use veg oil or waste motor oil with the blue board.

• 
  @simplyboating46096 ай бұрын

  Hi, I didn't know about the blue board. I know that black ones are sometimes different and are not compatible with the controller that's why its better to replace them both at the same time and try to get a generic one. .

• 
  @brianjohnson2176 ай бұрын

  Thank you for you chd controller info . I've tried all the ways that other tutorials show how to access the pump pulse rate ie Hz and up to now nothing has worked. I'll try your method the next time I'm in my workshop

• 
  @simplyboating46096 ай бұрын

  Hopeful it will work for you but since making this vlog i have come across 5 or 6 different controllers and some of them are not compatible with the CPU that comes with it. Before i could get this one working properly on my boat i had to change the CPC that was in it to a compatible one.

• 
  @Rivaboyz19876 ай бұрын

  There’s a water ski zone between oulton broad and near somerleyton it’s stretches for about 1.5 miles that’s why they circle ⭕️ and come back round think it’s between 4.30-8 in the evning there is a sight just up on the left hand side from where u r moored up that say water ski zone up there mate unfortunately for you wrong place wrong time it’s all legal

• 
  @simplyboating46096 ай бұрын

  I know i see it on the way back. Like you say wrong place wrong time but they where having fun.

• 
  @Rivaboyz19876 ай бұрын

  @@simplyboating4609 it’s a nice little spot that u can just walk up to oulton broad from there cut through st Michaels church

• 
  @simplyboating46096 ай бұрын

  Something new to try out, how long would it take do you think ?

• 
  @Rivaboyz19876 ай бұрын

  @@simplyboating4609 iv done it before we run out of fuel in that spot where u was and had to take the petrol can to the shell garege in oulton broad I would say it took about half hour 45mins depending on if you have to wait at the train line to cross over onto fishers ro to go up the path to where near the church is chuck a right onto hall road then up to the spar shop opposite there is a cut through subway onto Caldecott road then from there it’s a left past the commerdor pub

• 
  @Rivaboyz19876 ай бұрын

  What’s the mooring’s fees like on a boat your size mate can you pay monthly or is it a annual thing I’m looking for a mooring for my Norman 21

• 
  @simplyboating46096 ай бұрын

  Hi. you can pay monthly, quietly or annually. I think 21ft is about £120 pm but that includes as many lifts as you like and you will be dry stored. Just give them 30 mins notice and they drop it in the water for you. As your not in the water all the time its very safe as well. Its a very good compound to with cameras all over and a big steel fence around. Its cheaper in Beccles Yacht station but by the time you have your boat lifted out for a service it don't make much difference.

• 
  @Rivaboyz19876 ай бұрын

  What’s the rough price mate iv just brought a Norman 21 needs a new canopy.looks lovely in the gray mate nice looking boat that 👏

• 
  @simplyboating46096 ай бұрын

  Hi, they seem to vary a lot in price from about £750 to about £2000 depending on quality. I have also heard of people making them their self for £450. The one on this boat was £1360. Hope this was helpful.

• 
  @Rivaboyz19876 ай бұрын

  Nicest part of the river Waveney that is between beccles and geldeston lovely place in the summer to get the boat out 🙏🏻

• 
  @simplyboating46096 ай бұрын

  Most of the time it very quit as well which i like.

• 
  @Rivaboyz19876 ай бұрын

  @@simplyboating4609 perfect for cruising I tend to go up braydon water on my speed boat as there’s no speed limit up there

• 
  @simplyboating46096 ай бұрын

  @@Rivaboyz1987 I see someone water skiing there and all i could think is that's got to be cold if you go in.

• 
  @Rivaboyz1987Ай бұрын

  We wake board up there in the summer it’s not to bad tbh July through to early September but sod doing it other time of the yr

• 
  @jaimoallen84416 ай бұрын

  Hi have you got a link for the motherboard and controller please

• 
  @simplyboating46096 ай бұрын

  Oniissy Car Heating Control Board, Car Air Diesel Heater 3KW 5KW 12-24V Motherboard W/LCD Switch Remote Controller amzn.eu/d/f9zDvCu amzn.eu/d/f9zDvCu Hope this helps if not just ask.

• 
  @MsLorisM6 ай бұрын

  Is there a way to program this heater to come on at a certain temperature and turn itself off at a target temperature? Or does a person have to monitor the temperature of the space and turn it on and off manually? As in while you're sleeping and you are sweating and wake up and realize that the temperature is very hot in your sleeping space? Or if the temperature falls below freezing and you are freezing as well and realize that in order to not freeze to death, you must turn on the heater?

• 
  @simplyboating46096 ай бұрын

  when your controller is on have you got 1to 6 or 8 to control your temperature ? If so then no but if you have a controller with Celsius then yes. Let me know what you have as it can be changed quite cheaply or i can talk you through how to do it.

• 
  @MsLorisM6 ай бұрын

  I don't understand the first sentence of your answer. My controller looks just like yours. My controller came with Fahrenheit.

• 
  @simplyboating46096 ай бұрын

  Have you got numbers on your display from 1 to 8 ?

• 
  @MsLorisM6 ай бұрын

  @@simplyboating4609 when I press the OK button it will show the time 16:20, 77 F, P-2,9, 12.4 V, E-00 If I press the cog button it will let me change the time, then it shows 1 on, then - - - -, then back to time

• 
  @simplyboating46096 ай бұрын

  Not the Ok button but when you turn it on what’s on the display ?

• 
  @FaithwalkerTodd6 ай бұрын

  12 V is too low for your battery health. A fully charged battery should be 12.7 V and you should never drain it to more than 50% of its capacity which should be at about 12.2 V.

• 
  @simplyboating46096 ай бұрын

  The 12v on this is only telling you if you are on a 12v or 24v system.

• 
  @FaithwalkerTodd6 ай бұрын

  @@simplyboating4609 Ah!

• 
  @Timblake546 ай бұрын

  Hey, do you have any idea how to turn off the system completely? I tried holding on the power button but the fan kept blowing out cold air! I just ended up removing the fuze I had in

• 
  @simplyboating46096 ай бұрын

  Hi, It should take about 10/15 mins to shut down from the time you turn it of so it can cool down and not damage your CPU.

• 
  @simplyboating46096 ай бұрын

  Hi Tim, I have just looked it up and if you are waiting the 15 mins and it's still not shutting down then it my be that you motherboard is not working properly but try giving it 20 mins to cool down first and go from there.

• 
  @paulowen39346 ай бұрын

  @@simplyboating4609 when its blowing cold air on startup it could be faulty temp sensor

• 
  @totenvt6 ай бұрын

  strewth it floats ????

• 
  @simplyboating46096 ай бұрын

  I look at each time i go passed thing is it still afloat. He has now stopped the leaks after about 2 years.

• 
  @elizabethtruman71646 ай бұрын

  Kind of you to help a fellow In need ,😊😊

• 
  @simplyboating46096 ай бұрын

  It's only a temporary fix to keep him warm for now but needs to be installed properly but better than him getting to cold.

• 
  @robertgillott70346 ай бұрын

  Really think you should be using marine use silencer which is completely air tight, just a thought

• 
  @simplyboating46096 ай бұрын

  You are completely right that's what i have but he can't afford it at the moment as they are about £50 but he is going to change it when its installed properly same as the pipe work as its better if you have ISO 7840 but again he can't afford it but it is only temporary to give him a bit of heat while he is fixing it for the next month or so.

• 
  @dancarter4826 ай бұрын

  Fuel filter's back to-front, it's supposed to fill the chamber then make its way through the gauze. Pump should be under the unit so it's pressurizing just fluid and no air .. .. .

• 
  @simplyboating46096 ай бұрын

  These 50p fuel filters that come with it don't have a flow direction on them so you can put it whatever way you like, If you buy a good fuel filter it will have a flow direction on it and a water separator but costs about £35 As for the fuel pump you would struggle to get the pump under the heater especially if you were fitting it in a van as all the pipework goes out underneath. You would also struggle on the initial start up to get the air to go downhill to the pump as air likes to go upward. Thanks for watching this video so closely and pointing these things out as it's always good to know why it is like this. Please feel free to point anything else out in the future.

• 
  @dancarter4826 ай бұрын

  @@simplyboating4609 If you run your fuel line down from the tank to the base of the wooden stand then the pump fixed to the wooden stand with a short run straight up and into the unit that'd be your best routing. The filter's designed to show contaminants in the chamber - so it fills the large chamber first then that volume is screened before exiting and if neglected, the chamber can retain a lot of debris before strangulation begins.. ... I _only_ use water separator/filter units but my machines are all the expensive German variety!

• 
  @dancarter4826 ай бұрын

  When installed in vehicles, the pump should always be outside and underneath the unit along with exhaust etc.@@simplyboating4609

• 
  @DeeBarrymore6 ай бұрын

  Great video. Might consider having one put on my yacht for next winter. Although never drilled holes in a hull before and the thought of doing so scares me completely!

• 
  @simplyboating46096 ай бұрын

  I had the same thing about drilling holes at first until i fixed a hole on my boat. If you need some help with it just ask.

• 
  @DeeBarrymore6 ай бұрын

  @@simplyboating4609 Thanks I will and maybe can discuss it with you when on the Broads sometime!

• 
  @DeeBarrymore6 ай бұрын

  Oooh, I know that boat but I forget the gentleman's name. Usually bump (not literally) into him on Broads at Somerleyton.

• 
  @simplyboating46096 ай бұрын

  Jeff is his name. He seem to go between Beccles and Somerleyton, I don't think he can go much further as his engine over heats i was told. Maybe i will ask him if he would like me to have a look at it as i don't think it's a big problem same as the oil leak he had (small fix if you know how)

• 
  @DeeBarrymore6 ай бұрын

  @@simplyboating4609 Yes, that's him. His boat is often seen on other youtubers' videos just near the Beccles bridge alot. I guess for a liveaboard you need to be somewhere you can plug into an electric point but didn't think there was any on the free moorings at Beccles? Somerleyton has some and also Reedham and St. Olaves. Does he have a holding tank as I believe you also need one of them to get an annual Licence to be on the Broads?

• 
  @simplyboating46096 ай бұрын

  @@DeeBarrymore There are some free 24 hour moorings in Beccles but i see he is now in the yacht station for the winter. From what i see it's pretty much an empty boat, just a mattress in the cabin and a log burner. He is mid 70 and just needs a bit of help.

• 
  @user-ij7ef9pq4i6 ай бұрын

  Brilliant job well done helping a fellow boater

• 
  @simplyboating46096 ай бұрын

  Glad it was helpful to him.

• 
  @Bitsandboats6 ай бұрын

  Finely a proper video on how to fit these diesel heaters on a broads boat and a video that’s straight forward and easy to follow Thank you and keep up the good work 100% liked and subscribed 👍

• 
  @simplyboating46096 ай бұрын

  Thank you very much for your lovely comment, I'm so glad It's helpful and simple to follow.

• 
  @crissyb006 ай бұрын

  Proper? You're having a laugh. Oh look how the jubilee clips arn't big enough. Two min laters, using them on the inlet. Also, you gotta love the application of exhaust paste, but only around two thirds of the joint. This, was a vlog on how to gas yourself!

• 
  @Louis-wr9ft6 ай бұрын

  Great, easy to follow.

• 
  @Louis-wr9ft6 ай бұрын

  Very helpful.

• 
  @simplyboating46096 ай бұрын

  Glad it was helpful!

• 
  @Louis-wr9ft6 ай бұрын

  Looking very nice.

• 
  @simplyboating46096 ай бұрын

  Thanks a lot

• 
  @Jen-fy3pj7 ай бұрын

  Nice surprise seeing your friend.

• 
  @simplyboating46097 ай бұрын

  It was a nice cupel of days.

• 
  @Rivaboyz19877 ай бұрын

  It’s absolute madness between April-September on the river with all them hire boats no where near as bad on the south side most of the hire-boats stay the north side people who own there own boat tend to no get along with the hire boats they have no training and are always damaging other boats I stay well away from em on my speed boat

• 
  @simplyboating46096 ай бұрын

  It can be a bit mad in the summer.

• 
  @Rivaboyz19876 ай бұрын

  @@simplyboating4609 not even just the summer it’s April to September pure chaos south side is much better between Oulton B-road and beccles or beccles to geldeston is the nicest part of the river with the nicest of people that’s why not many hire boats go up there there not very welcome due to them causing so much chaos a lot of people live in there boats full time in Oulton broad beccles and gelgeston so no one what’s there boat damaged or boozy cruisers up there causing unnecessary drama

• 
  @Rivaboyz19876 ай бұрын

  I’m pretty sure that boat over took you is the guys own boat I think he’s called the captains blog on KZread hence the boat being called captains b but I could be wrong

• 
  @Louis-wr9ft7 ай бұрын

  Nice job.

• 
  @simplyboating46096 ай бұрын

  Thanks!

• 
  @Louis-wr9ft7 ай бұрын

  Nice place, camp site looks good for the prices.

• 
  @simplyboating46097 ай бұрын

  It is very nice and they are very friendly in the pub.

• 
  @hauntingghosthunts59847 ай бұрын

  Good capture first thing in the morning

• 
  @simplyboating46096 ай бұрын

  Yes it was

• 
  @philm24177 ай бұрын

  Fancy making your dogs walk the plank :). Lovely scenery

• 
  @simplyboating46097 ай бұрын

  😂

• 
  @GD903417 ай бұрын

  On the pcb there is an hall sensor, on the new there is no one to see, how does it regulate?

• 
  @simplyboating46097 ай бұрын

  I not that technical sorry, all i can say is it works fine.

• 
  @michaelquigley14117 ай бұрын

  60 mph winds? Really? 60 mph? The wind?

• 
  @simplyboating46097 ай бұрын

  Maybe you need to ask the BBC Weather about it. kzread.info/dash/bejne/gJqmxMuTeMfdiKg.htmlsi=yUHBPPcyxOqgZ8u7

• 
  @Louis-wr9ft7 ай бұрын

  That top looks beautiful. What a lovely pice of wood.

• 
  @simplyboating46096 ай бұрын

  It really is a nice bit of wood

• 
  @stevegarrett10207 ай бұрын

  Sitting it out is the best you can be by the look of it,

• 
  @simplyboating46097 ай бұрын

  That's all i can do.

• 
  @jamrolypolypud7 ай бұрын

  Our wheelie bin blew over today...i resisted the urge to call 999...instead, i picked it up and got on with my day. Just like you're doing. Stay safe.

• 
  @simplyboating46097 ай бұрын

  Getting on with our days and waiting for it to stop is all we can do.

• 
  @Jen-fy3pj7 ай бұрын

  Lovely sunset.

• 
  @simplyboating46096 ай бұрын

  Yes it is.

• 
  @Louis-wr9ft7 ай бұрын

  Love the look of that worktop and you make it look so easy to fit.

• 
  @simplyboating46096 ай бұрын

  It is you just need to think about it.

• 
  @Louis-wr9ft7 ай бұрын

  You must do so much research to keep coming up with these ideas.

• 
  @simplyboating46096 ай бұрын

  I do try to research stuff.

• 
  @Louis-wr9ft7 ай бұрын

  Looks very nice, great finish.

• 
  @simplyboating46096 ай бұрын

  Thank you very much!

• 
  @Louis-wr9ft7 ай бұрын

  That was very helpful to see the difference.

• 
  @simplyboating46096 ай бұрын

  Glad it was helpful.