Пікірлер

• 
  @liljimmysfoodfactorygemstr40962 күн бұрын

  How about for the high beam bulb so do I have to disassemble that frame on top to get to the covers for it you have a video for it thanks buddy

• 
  @cesar4motion4 күн бұрын

  Great job, I allready see it, I have a question, at how many miles or kilometers have to changue these chains...??

• 
  @joshuamaina8469 күн бұрын

  Where did you get your 12v charger?

• 
  @MatthewWong9 күн бұрын

  Harbor Freight

• 
  @TheJoetuffguy2 ай бұрын

  Who TF lays tools on their vehicle? Wish I could delete this video

• 
  @mascho223 ай бұрын

  hey if you're still checking comments, did you use a 1/2" or 3/4" breaker bar for the bolt? Wondering if my 1/2" will break trying to loosen that crank bolt

• 
  @ladonnwilkerson70384 ай бұрын

  When he threw the sockets on his m I cried 😢

• 
  @josueortega33624 ай бұрын

  Hey man, i had a question. I have these same headlights for my 13 bmw 328i and i have a parking lamp malfunction. Any chance you know the bulb i need to change out?

• 
  @MatthewWong4 ай бұрын

  Try pulling the bulb out and look at the back. I found mine corroded over time and needed a bit of sanding down to make a better connection. Otherwise it might be the bulb.

• 
  @leveragelifestyle85814 ай бұрын

  Great vid. I think if you left the cap open for the fill talk while bleeding you wouldn't need to open the bleeder screws. The air comes out of the port that shoots the coolant back into the tank as it recirculates.

• 
  @adeelahmed86414 ай бұрын

  How many times would you need to drain coolant to get radweld out? It's blocked my heaters

• 
  @stanponkratov2694 ай бұрын

  Good stuff man!! gives me the courage to tackle projects that may seem limiting at first.

• 
  @stanponkratov2694 ай бұрын

  Thanks!

• 
  @gilrobertonavaperz27014 ай бұрын

  Más de una hora mirándole el lomo a este gay

• 
  @Fly-SanDiego5 ай бұрын

  Flip flops and cardboard boxes. The standard for DIY garage mechanics for years.

• 
  @numbnutz6265 ай бұрын

  That was so beautiful. It's my dream to go there someday. Thank you.

• 
  @ladjkaoz5 ай бұрын

  great content. 👍👏👏

• 
  @ladjkaoz5 ай бұрын

  would you show what or where does the tendioner push... I may had miss that part.

• 
  @ladjkaoz5 ай бұрын

  why not just remove all that old platic... just use new tensioner...

• 
  @MatthewWong5 ай бұрын

  Just decided to try it out. My plastic was cracked anyways

• 
  @hydn796 ай бұрын

  Did the ticking noise go away or is that something else?

• 
  @MatthewWong5 ай бұрын

  That's just the n20 engine

• 
  @MatthewWong5 ай бұрын

  Injectors

• 
  @EmmaRides6 ай бұрын

  I can hear Abba @11:00

• 
  @mingelius2068 ай бұрын

  Is that oil good for hot area

• 
  @MatthewWong7 ай бұрын

  Not entirely sure. Perhaps consult with local dealer? f30.bimmerpost.com/forums/showthread.php?t=954409

• 
  @r3gflm9169 ай бұрын

  How was well was your car running when it was like this? Loud? Misfires? Error Codes? Love the videos you took! Thanks man,

• 
  @MatthewWong9 ай бұрын

  Misfired at first but I realized it was becuase I didnt have one cylinder hooked up (ignition coil). Freaked me out. But after it ran fine! Just a bit of smoke on start up since it sat for so long. No codes

• 
  @Ricardo-eg3wn10 ай бұрын

  Please tell me how you have a f30 with power steering. You don’t have power steering. There is no fluid. It’s electric guy.

• 
  @robzilla60910 ай бұрын

  Take the spark plugs out before turning the engine over. Next time. It will be beneficial for fighting compression.

• 
  @alexanderstefanxandraswedi583511 ай бұрын

  Welcome hade been Cambodia

• 
  @ramiropantoja72311 ай бұрын

  Donde el taller Diresion

• 
  @brandongarcia5116 Жыл бұрын

  Anyone knows how to take out the cap from below if it’s stripped? 😢 I’ve been trying for hours

• 
  @MatthewWong Жыл бұрын

  Oil drain plug is stripped?

• 
  @brandongarcia5116 Жыл бұрын

  Yup, I went to the store to get a full set of Allen wrenches and none worked, it keeps slipping 😓

• 
  @vinnysv8 Жыл бұрын

  Very informative and fun, ty for the help!

• 
  @hectorsuarez6166 Жыл бұрын

  Gracias por tu video hermano 🇨🇴🇺🇸

• 
  @TheDonz Жыл бұрын

  I got a new timing chain installed, mine also doesnt move at all

• 
  @eznuk66 Жыл бұрын

  Great. how do you set the HNCS-Mode? Is it automatically if you choose Normal instead of Hlog, D-Log or D-Log M?

• 
  @guccipig2782 Жыл бұрын

  Was your car running fine before you did the timing ?

• 
  @MatthewWong Жыл бұрын

  Yep

• 
  @guccipig2782 Жыл бұрын

  @@MatthewWong oh ok. Cuz I have the same car and my timing chain is just as slack as yours in the video. And I’m getting a misfire on cylinder number 1. I’ll replace the injector and coil to see if it fixes the misfire. I already did all four spark plugs just recently.

• 
  @romanobrown5592 Жыл бұрын

  @@guccipig2782 what was the code

• 
  @guccipig2782 Жыл бұрын

  @@romanobrown5592 the injector wasn’t seated right so the Teflon seal kept melting away. I fixed the issue now. It runs fine.

• 
  @RandomVidz9_ Жыл бұрын

  Hey when adding coolant do you have to have all 3 bleeder screws open then when it starts leaking out coolant close it up and start bleeding procedure? If so how open do u have the bleeder screws all the way out or half way?

• 
  @MatthewWong Жыл бұрын

  I tried all three at first until they started leaking out. Then I tried each individually about 2-3 more times to make sure there was no air

• 
  @beautycm27 Жыл бұрын

  Women: You don’t have to pull off the wheel. Turn the wheel to the opposite side and pull off covering. Then fish your hand in and remove the bulb. Watch the front lamp as you replace the new bulb. Use your tactile senses and this converts to an easier less laborious task. Benefits of small hands 😅

• 
  @Centralflorida22 Жыл бұрын

  ❤

• 
  @SOHAIL50280 Жыл бұрын

  Thanks brother

• 
  @gabrielpagliaro1834 Жыл бұрын

  hello and congratulation can you send me price of that tool and price to send ti miami? thanks gabriel

• 
  @weldon29 Жыл бұрын

  Is the new one more durable than the old one?

• 
  @MatthewWong Жыл бұрын

  Not sure but BMW did upgrade the parts

• 
  @DK-pg4hl Жыл бұрын

  Your in Oregon I’ll help you switch it out I’m going to do mine!

• 
  @MatthewWong Жыл бұрын

  I did mine last summer! I have a full video up on my channel

• 
  @RandomVidz9_ Жыл бұрын

  Do u have to open up the screw during bleeding procedure? Cuz i mostly see them just pour coolant in then start bleeding procedure, they say the water pump will do the work and take out the air and then u just top it off with more coolant, is that true?

• 
  @pericodelospalotillosverdes Жыл бұрын

  This purging procedure is indicated by the mark, when the electric water pump is changed.

• 
  @mikimiki195 Жыл бұрын

  Did you buy timing tools or you rented it ?

• 
  @MatthewWong Жыл бұрын

  I bought off Amazon and returned after

• 
  @HiMyNamesTrill Жыл бұрын

  horrible video no help beside to go watch some else

• 
  @rafaelbetancourt3551 Жыл бұрын

  I had seen the FCP Euro video and was a bit overwhelmed with the job. I have done plenty of brakepads, alternator / radiator / hoses before. After watching your video and hearing your advice I feel brave enough to do this myslef.

• 
  @MatthewWong Жыл бұрын

  I was also but I decided just do it. The car was up on jacks longer than I thought maybe 2-3 weeks instead of a weekend. Make sure to have all your tools beforehand and it'll go much faster.

• 
  @indymajors Жыл бұрын

  Also, so does the updated BMW chain and chain guide fix the premature failure issue? BMW seems to recommend that this N20 engine needs a new timing chain every 100,000 kilometers, which is every 62,000 miles! If the new chain and tensioner are not defective, can I wait to do this every 100,000 miles? Is there are upgraded chain that lasts longer? 100k miles is a lot, but honestly, I think these chains should last a lot longer given the work involved in replacing...

• 
  @MatthewWong Жыл бұрын

  I've read of a couple engines that did go out on forums after replacement of chain and guide. Not sure if its due to incorrect installation or something else but I think the failure numbers are still exponentially lower than that of the original chain + guides

• 
  @DuckMcDuckinson Жыл бұрын

  No you’re supposed to do it ever 100k

• 
  @MatthewWong Жыл бұрын

  @@DuckMcDuckinson yeah sounds about right I just did preemptively

• 
  @DuckMcDuckinson Жыл бұрын

  @@MatthewWong also brother. Use AMSOIL European Formula 0W-40 FS. Your guides will last longer on a 100% synthetic oil. For $20 a year, you get 25% off all their products or you could do $10 for 6 months.

• 
  @indymajors Жыл бұрын

  If the chain guides and tensioner are the root cause for the early failure of these chains, can I get away with changing only the chain, chain guide, and tensioner? Can I skip the oil pump chain replacement and skip all this engine jacking and oil pan removal stuff? If the timing chain breaks, that can badly damage the motor, but if my oil pump chain goes, it seems less catastrophic and I can just replace that chain when and if it ever happens...

• 
  @MatthewWong Жыл бұрын

  Unsure since BMW did update the chain itself in the oil drive part. I think theres just a lot of variables and points of failure in the system in general which is why its recommended all components be replaced since you are in there anyways.

• 
  @alecpajor9273 Жыл бұрын

  I’ve been running this kind of oil all year around it gets pretty cold in the winter I live close to nyc so 30 degrees sometimes below. Is this ok. I just stage 1 tune as well.

• 
  @edwardsarah957 Жыл бұрын

  Thanks for the Info but, the Music is crazy Loud🤯😖

• 
  @nickykodak7536 Жыл бұрын

  Why would anyone - for any reason - leave any comlicated digital item in such conditions?

• 
  @voiceofreason891 Жыл бұрын

  Might have been easier to remove the return hose from the reservoir and use it to dump into a waste container. Start vehicle and add fluid as it pumps. Stop when things look good. Also as others stated, replace the reservoir too because of the screen.

• 
  @stevesandiego99 Жыл бұрын

  Really great video thank you so much. I have a question. Looks like some kits include the Intake VVT Gear and Exhaust VVT Gear, as well as the VANOS central valves. Should I be replacing these as well?

• 
  @shimon24764 ай бұрын

  Only if you had vanos codes prior