You have great energy man, may you continue to prosper 🙏
@Sheeesh99Күн бұрын
You have great energy man, may you continue to prosper 🙏
@vadimkozlov3008Күн бұрын
I removed a 70 foot gutter from a place i was fixing up and spent days trying to figure out how they got it there. I was convinced they used a flatbed to bring a single gutter over... this makes so much more sense.
@ninetyseven7656Күн бұрын
Impressive
@JoeyVXКүн бұрын
That shiitt looked sloppy screwed in
@user-ot1dv6ri4f2 күн бұрын
Showing off and making a leaky gutter
@ManuelMartinez-hx8gs2 күн бұрын
How do you do it when the drip edge is hugging the fascia too close
@Redact63Lluks2 күн бұрын
Call the roofer 😂
@dietcomedy12 күн бұрын
Pry it out with benders hope it doesn't damage it or put gutter on top of the drip edge and install new one second layer?
@EarlyBirdArmsКүн бұрын
Pry it away a little. Doesn’t take much. Super annoying though
@devaughndavies9207Күн бұрын
@@dietcomedy1 please tell me you don't install gutter cause if your putting screws through the drip edge just retire and shut down shop. Water will leak into the screw holes and rot out the fascia board momo
@dietcomedy1Күн бұрын
@@devaughndavies9207 on my last sentence I wrote-put a new second layer after installing on top of first layer of drip that's too tight
@TREASONHUNTER3 күн бұрын
It's not as high as it is steep🫡
@joseleyva5593 күн бұрын
I like the set up good job
@joseleyva5593 күн бұрын
Good job
@dietcomedy13 күн бұрын
This way better than plastic
@Longecko4 күн бұрын
Love you Tony your the man # bigdogsgottaeat
@Longecko4 күн бұрын
Royal gutters has it all... very professional and Tony's awesome dude 😎
@LAR-hs2qt4 күн бұрын
Thank yah.
@Red-dit.Stor-ies4 күн бұрын
The exterior finish isn't on the house. They do that to mark the down spout location and allow water to drain out of the trough. Tell me you're new to construction without telling me. Lol
@dietcomedy14 күн бұрын
Gotta check yourself to make sure not over heating 😊
@ryancooke19814 күн бұрын
Why are you paying attention to the temperature of Copper vs White gutters?
@vperson9923 сағат бұрын
The higher the temperature, the more the gutter stretches. A 50’ long gutter with a 50 degree temperature changes stretches a copper gutter just over 1/4”. Different metals will stretch differently. The more it stretches, the more likely the joints will tear themselves apart and start leaking.
@user-ci7iy3ge1t4 күн бұрын
We buy from China wholesale.. and resale retail..same style 😊
@dietcomedy13 күн бұрын
Plastic?
@user-ci7iy3ge1t3 күн бұрын
Pvc
@Ninjump4 күн бұрын
Thanks so much for the video. Im a general contractor who self performs lots of different stuff. Learned a ton, thank you!
@nicholasmoore14534 күн бұрын
Who fucked up lol
@MrStimpy4695 күн бұрын
how stupid is that idea
@Reir0o5 күн бұрын
disrespectful..
@Astinsan5 күн бұрын
hope that isn't going into the weeping system ... mike homes is gonna have a fit
@cumulusvapes75 күн бұрын
Who would use STEEL in 2024?!
@crakkbone5 күн бұрын
You should use aluminium for that. It won’t rust.
@vperson9923 сағат бұрын
Aluminum stretches about 40% more than steel. With a plain and contemporary design with a dark color, aluminum will oil can (the gutter will be all wavy and ugly). Commercial work, steel is preferred. If the gutters are maintained with no standing water, it will take 50+ years to see rust on this 24ga steel painted inside/ out with a kynar finish.
@DjMeowMixAlot5 күн бұрын
Are you looking for an experienced installer?
@daneberhardt86585 күн бұрын
I'm at the age of being impressed with rain gutters! Great idea with those clean-outs
@Jeffreyrbrady5 күн бұрын
So why are gutters so expensive?
@dietcomedy16 күн бұрын
Gutter life hack
@pvmcorp6 күн бұрын
Is this a custom made planter box?
@troyhonda717 күн бұрын
They need to maintain their home better
@wilfredotorres88807 күн бұрын
We use them everyday. There great!
@2minniegirl7 күн бұрын
I hear a difference between those 2
@honeybear46757 күн бұрын
Why is your sealer hanging from the gutter and your hammer in it no tool belt doesn’t that scratch the gutter just did a black gutter job today and I would never it takes nothing to scratch black aluminum
@wadeuww9wmsksznzkknuttall4227 күн бұрын
Looks super out of line to me I dont do roofs but I like things to be right and straight 😊
@allanmichael16267 күн бұрын
I like the pre made slide in version
@JaeRock-tv1zv9 күн бұрын
That was a bad choice now he's going to have the police station on him and he's going to get clapped
@user-ey6ps9nc1z9 күн бұрын
What's your adress so I can mail u some crimpers
@user-ey6ps9nc1z9 күн бұрын
You can punch in the hole for the outlet too lol 😅
@tarcisiocardoso784610 күн бұрын
Hello my friend
@skinlab423910 күн бұрын
Wow. Common sense
@michaelknight156310 күн бұрын
Ya take ur AAA ......... Hammer don't smoke before making the video bro your not coming across relaxed
@johnotoole578610 күн бұрын
Just snip them down to hidden u straps if maintaining same color
@johnotoole578610 күн бұрын
Is this a parody clip
@darknessrules210 күн бұрын
Most people just screw em in now and days so ill trust my loyal kobalt to get it out
@Mc-RaGe-In10 күн бұрын
No hangar’s? If you were real good you could do that at the same time 😂😂
@dougd.892511 күн бұрын
Good to know thanks for showing us
@8601a11 күн бұрын
"Claw" was the word that wouldn't come.
@EarlyBirdArms11 күн бұрын
Or you can cut it off. You can also just pull them out with your hands 99% of the time. I’ll undo the top one, realize it’s a nail, the. Use the downspout itself as a giant lever to pry the bottom one out. Then pull the top one out by hand. I don’t carry a hammer unless I need it. Too much extra weight for someone I don’t use much for install
Пікірлер
You have great energy man, may you continue to prosper 🙏
You have great energy man, may you continue to prosper 🙏
I removed a 70 foot gutter from a place i was fixing up and spent days trying to figure out how they got it there. I was convinced they used a flatbed to bring a single gutter over... this makes so much more sense.
Impressive
That shiitt looked sloppy screwed in
Showing off and making a leaky gutter
How do you do it when the drip edge is hugging the fascia too close
Call the roofer 😂
Pry it out with benders hope it doesn't damage it or put gutter on top of the drip edge and install new one second layer?
Pry it away a little. Doesn’t take much. Super annoying though
@@dietcomedy1 please tell me you don't install gutter cause if your putting screws through the drip edge just retire and shut down shop. Water will leak into the screw holes and rot out the fascia board momo
@@devaughndavies9207 on my last sentence I wrote-put a new second layer after installing on top of first layer of drip that's too tight
It's not as high as it is steep🫡
I like the set up good job
Good job
This way better than plastic
Love you Tony your the man # bigdogsgottaeat
Royal gutters has it all... very professional and Tony's awesome dude 😎
Thank yah.
The exterior finish isn't on the house. They do that to mark the down spout location and allow water to drain out of the trough. Tell me you're new to construction without telling me. Lol
Gotta check yourself to make sure not over heating 😊
Why are you paying attention to the temperature of Copper vs White gutters?
The higher the temperature, the more the gutter stretches. A 50’ long gutter with a 50 degree temperature changes stretches a copper gutter just over 1/4”. Different metals will stretch differently. The more it stretches, the more likely the joints will tear themselves apart and start leaking.
We buy from China wholesale.. and resale retail..same style 😊
Plastic?
Pvc
Thanks so much for the video. Im a general contractor who self performs lots of different stuff. Learned a ton, thank you!
Who fucked up lol
how stupid is that idea
disrespectful..
hope that isn't going into the weeping system ... mike homes is gonna have a fit
Who would use STEEL in 2024?!
You should use aluminium for that. It won’t rust.
Aluminum stretches about 40% more than steel. With a plain and contemporary design with a dark color, aluminum will oil can (the gutter will be all wavy and ugly). Commercial work, steel is preferred. If the gutters are maintained with no standing water, it will take 50+ years to see rust on this 24ga steel painted inside/ out with a kynar finish.
Are you looking for an experienced installer?
I'm at the age of being impressed with rain gutters! Great idea with those clean-outs
So why are gutters so expensive?
Gutter life hack
Is this a custom made planter box?
They need to maintain their home better
We use them everyday. There great!
I hear a difference between those 2
Why is your sealer hanging from the gutter and your hammer in it no tool belt doesn’t that scratch the gutter just did a black gutter job today and I would never it takes nothing to scratch black aluminum
Looks super out of line to me I dont do roofs but I like things to be right and straight 😊
I like the pre made slide in version
That was a bad choice now he's going to have the police station on him and he's going to get clapped
What's your adress so I can mail u some crimpers
You can punch in the hole for the outlet too lol 😅
Hello my friend
Wow. Common sense
Ya take ur AAA ......... Hammer don't smoke before making the video bro your not coming across relaxed
Just snip them down to hidden u straps if maintaining same color
Is this a parody clip
Most people just screw em in now and days so ill trust my loyal kobalt to get it out
No hangar’s? If you were real good you could do that at the same time 😂😂
Good to know thanks for showing us
"Claw" was the word that wouldn't come.
Or you can cut it off. You can also just pull them out with your hands 99% of the time. I’ll undo the top one, realize it’s a nail, the. Use the downspout itself as a giant lever to pry the bottom one out. Then pull the top one out by hand. I don’t carry a hammer unless I need it. Too much extra weight for someone I don’t use much for install
Well that was fucking painful to watch.