I found this video a couple years ago when having this issue with my JDM Camry Gracia and couldnt find the issue with all sensors sending and reading properly, so I got the resonator and all to do this repair, but never bothered to replace it because I'm lazy. It finally conked fully out this week, just replaced that resonator and BOOM everything is perfect again. You are a godsend with this video my man, if it wasn't for this, I'd probably still be losing my mind trying to find out what's wrong.
@alanmichaelclarosescobar422326 күн бұрын
Where do I get ur book for the Toyota I’m trying to get one for the 1997 hilux surf
@jeffharrell187426 күн бұрын
I bought a Haynes repair manual I found on eBay used. I believe Haynes only published vehicles for the US. You might find the info you need from a Haynes 1997 4-Runner manual.
@johnnydarko198327 күн бұрын
Had all three issues, emphasis on "had" but not any more thanks for the video. Mine is a 1997 Toyota Camry XLE 2.2L for reference.
@elecmusoАй бұрын
Hi Jeff. Any idea whether this solution works for a 2004 Lexus GX470? There seems to be a common scenario for that vehicle where the speedometer is stuck at 0 but the odometer continues to function (and thankfully the transmission shifting also behaves itself) which is of course different to the 3 symptoms you've described. I'd give it a try only I have to order the part first and without having taken out the cluster yet I can't site the component to make sure it is the same value - so I guess my first question is do you know if the component is the same for that model vehicle? Or anyone able to direct me to a circuit diagram (or photo even) for the GX470 speedo itself?
@jeffharrell1874Ай бұрын
You might have a speed sensor issue. I don’t think your root cause is the same as in this video.
@AngelOliva302Ай бұрын
I was able to fix it on my 1998 Toyota Camry thanks to your Instructions - I'm driving proud now and the chicks dig my car!...Lol - Thanks!
@davidn91492 ай бұрын
After 2 speed sensors and checking for loose fuses I jumped on KZread to find this and similar videos. Thanks Question? Soldering the blue ceramic resistor on the opposite side? Does that interfere with assembly? Seems it could.
@jeffharrell18742 ай бұрын
It does not, and it makes it so much easier. Good luck!
@mariomezajr.83982 ай бұрын
My speedometer works good, but my odometer doesn’t show all numbers, if my tundra has 123,467 miles it shows 1 3,46 incomplete does this fix this issue ? I don’t want to buy a new cluster just for that
@jeffharrell18742 ай бұрын
I’m not sure if this helps in your case.
@mirceatudorache80912 ай бұрын
Amazing video, appreciate a lot!
@alexrcroes3 ай бұрын
Worked!! Thank you for the easy fix!
@MichaelPittmanJr.3 ай бұрын
Can the place be put onto the front, replacing the old one?
@jeffharrell18743 ай бұрын
After removing the bad capacitor, the new one can be installed on either side of the electronic board. But it’s much easier to install through the back.
@farazsiddiqui66894 ай бұрын
I just replaced the instrument cluster on my 4Runner since the last had a broken screen. Everything seems good except the odometer is blank. Trip A and Trip B both work. Any ideas? TIA.
@jeffharrell18744 ай бұрын
If your speedometer is still working, this may be a different issue within the instrument cluster. I’m not sure what that would be.
@blap94674 ай бұрын
How do you put the tube seals in?
@jeffharrell18744 ай бұрын
There’s multiple ways, depending on what tools you have available. It’s possible to use just a hammer or mallet alone to lightly tap them in. I’ve heard of people using a socket or pvc piece of the same diameter of the seals to help evenly apply force on the seal to help it fully seat in place. If I remember correctly, I think I only used a small hammer to carefully tap all around the seal. It’s not the easiest method, but it’s better than hammering against a flat head screw driver which could slip out of place and cut through your seal. I made that mistake and had to buy another set of tube seals lol.
@BimmerFordDude5 ай бұрын
This is by far the best video for this job! Pain in the butt process and solidifies my hate for front wheel drive cars. So much easier on a RWD car! 😡
@damacknificent1515 ай бұрын
Nine didn't blink fast or anything. It kept giving me code 33 on my 1997 toyota 4runner any other way to clear it?
@jeffharrell18745 ай бұрын
Have you already changed the abs/speed sensor for that wheel?
@damacknificent1515 ай бұрын
@@jeffharrell1874 yes
@jeffharrell18745 ай бұрын
@@damacknificent151 it’s possible that some variation of the number of brake pedal presses may help clear the code if the part swap was a success. If that doesn’t work, then it may be necessary to use a special scan tool that can recognize Toyota abs codes, or further diagnosis from a mechanic.
@jamesguralski51565 ай бұрын
Yes this worked! I changed my front driver's side cv shaft and hub and bearing! It ended up being just metal fillings on abs wheel speed sensor! Just clean it up ... Did your rest method. Vala
@joecagle90856 ай бұрын
Where did you get the resonator? Never did hear you give the site to get it.
@jeffharrell18746 ай бұрын
Look in the video description. You’ll find some links.
@lightshine60446 ай бұрын
Does this method work for 97 toyota camry 4 cylinder? or does it have to be 6 cylinder?
@jeffharrell18746 ай бұрын
I believe it should work either way
@Tbonner08186 ай бұрын
Awesome..Thanks! Found a new hatch handle on Amazon for $12.
@BG-xh5rb6 ай бұрын
It's a good video without all the fanfare, bells, and whistles. No excessive rambling or camera jerking. Thanks for the fix!
@user-gw1gz9nt2l7 ай бұрын
What is the link to get the part if u will can u send it to me
@jeffharrell18747 ай бұрын
There should several link options in the video description.
@bigdogkropp7 ай бұрын
Be prepared for the outer cover clips to break. You can buy an assortment of different size clips online for cheap.
@khengratha32647 ай бұрын
Thank for sharing! Is it possible for you to share toyota camry third gen. problem?
@guitarshred8637 ай бұрын
Hello , Jeff , thank you for responding. basically . I was changing a sparkplug of a V 6 Rx 300 0f '01. the sleeve of sparkplug at the back ,broke off where the hard palstic , about 1/2 inch. I have the sparkplug out . I did everything possible to pull it out . after lubricaring with silicon , it doesn't even turn . I was thinking of drilling it to pieces, and after that , vacuum inside . will it work? Thanks.
@jeffharrell18747 ай бұрын
It’s hard for me to picture what you have going on. I would get a knowledgeable mechanic friend to take a look or send him pictures of your current situation, then see what he advises to do. You don’t want to do anything that could cause any pieces to fall through the spark plug hole and into the engine.
@jamesdavidian77177 ай бұрын
You are a gangster!
@guitarshred8638 ай бұрын
hello, with th 6.75 ft/lbs torque on your valve cover i can still see the the gasket , I used the blue gasket and its visible within the gap . that is supposed to be?
@jeffharrell18748 ай бұрын
It’s possible you may see the gasket slightly. Confession: I did not use a torque wrench to tighten mine. I did it just by feel, but be careful not to do it too tight or you could break a bolt or thread (which I’ve done before 😬)
@remogaggi823 ай бұрын
I’m seeing the gasket on mine too. I only did the front cover so far. Seems like a huge gap but I torqued to spec. Any leaks? Doing rear valve cover tomorrow and hope I didn’t screw up
@baileyRTRnelson8 ай бұрын
Thanks for the video brother.
@garywanner78608 ай бұрын
Thank you, you described exactly what I’m experiencing with my 99 Camry.
@sidefx9969 ай бұрын
Thank you so much for taking the time to make this and help others out. My abs light came on and I tried several different scan tools, including one I was told cost more than my car. The paper clip gave me the only accurate diagnosis. Two wheels sensors later the ABS light turned right off and I'm back in business with the ABS working perfect once again. Thank you again and God Bless.
@uncleknucks9 ай бұрын
My speedometer sits at 0 but odometer stays at 147k and I get the erratic shifting. CEL code P0500. Do you think its the speed sensor on the bell housing or the blue resonator in the cluster?
@jeffharrell18744 ай бұрын
It’s sounding like the resonator. Worth a shot for only about $5 and some time.
@zoltanfebert-zx1gs9 ай бұрын
Does the tach also have a ceramic resonator? My Speedo and tach are both acting up!
@taylorh9569 ай бұрын
Did this and it screwed up my speedometer more. Have to get a new one.
@MENU37010 ай бұрын
I have the exact problem...97 Lexus ES300😢 but I can't find a ceramic resonator for it...help please...display the link ...🙏 ( I already replaced both speed sensors) major tune up 😂 and nothing & Reset the speedometer / cluster
@jeffharrell187410 ай бұрын
The link is displayed in the video description.
@roberthodges126710 ай бұрын
Thanks for the video that fixed the issues and got it back on the road.
@samblumen632111 ай бұрын
This is the gift that keeps on giving. Very similar presentation 1998 Toyota Sienna with 244K miles. When hot day (we are in Texas) there is no odometer display or speedometer operation. On cool mornings it works fine and is a happy camper. This has been so frustrating. Your technique for soldering is novel but very acceptable. This video was very well done and your documentation is extremely solid. I will report back success / failure after part(s) arrive and procedure completed. Again, thank you so much for the very excellent video.
@jeffharrell187411 ай бұрын
Good luck! I think it’s worth every effort to keep these Toyotas on the road. They are so well made!
@sitipatsitichaiboonrueng333711 ай бұрын
Thank you so much. It worked for 99 camry
@terryodonnell724911 ай бұрын
I put the same part Digi Key 490-18260-ND into my 99 Avalon and it cooked the speedometer board. After carefully soldering the part to speedometer, I immediately smelled electrical issue when on turning on the ignition. I removed the speedometer to see the board had a burn on it. Doing a continuity test on my newly soldered connection posts (3) there was no problem between them, no short. This is a similar "replacement part" to the original part suggested in another video that is no longer available PN # x902-ND - maybe the problem? I've bought a used cluster to install. Best to ya's, God Bless...
@daejohneeleslie666711 ай бұрын
Awesome video I like how short it is and very helpful !
@ovanestopchyan175511 ай бұрын
Can someone please tell me if this will work on my 1998 Lexus LX 470? Thanks
@jeffharrell187411 ай бұрын
What symptoms are you having?
@amandamiles458011 ай бұрын
Tried this today on my 97 Lexus es300. And my car is still not allowing the speedometer to work. I'm guessing the next step is purchase an entirely different cluster panel.🤦♀️
@jeffharrell187411 ай бұрын
Was your odometer not working before as well?
@bikersoncall Жыл бұрын
Informative, thanks! Your volume is very low, the ads are 10 times louder.
@jeffharrell1874 Жыл бұрын
Agreed. Volume isn’t good. KZread newbie here 😂
@bikersoncall Жыл бұрын
@@jeffharrell1874 haha, I don't know much about doing videos, I just know how to vol adjust in my Filmora lol . I see you have two more vids related, to the Rx300, I wish you had 30, great job on this video. I just bought a 2001, not too many issues right now, just trying to learn my way around it , so I'll be able to handle future issues. I had to take off my rear wiper, as I'm in the middle of the rear window replacement, it is a substantial project.
@bikersoncall Жыл бұрын
00:09 Recommended wiper-arm removal? I had to use a mechanical puller, not sure if twisting the motor around like that is ok and why that even helped in the removal..shrugs.. Is this in 'a' manual, or it just worked for you?
@jeffharrell187411 ай бұрын
No manual was used for this process. Turning it allowed me to position it in a way to relieve the tension so that it could be pulled off easily. Motor was not harmed.
@geedog813 Жыл бұрын
So helpful nice one !!!!
@LB_6R Жыл бұрын
Thank you for this video. You saved me time, money, and knuckle busting frustration. Easy fix on 99 RX300. (280,000+ miles)
@bikersoncall Жыл бұрын
Me too, mine isn't broken, but I wanted to know how to access parts back there. Really good video.
@EverH0p3 Жыл бұрын
Great stuff! So the resistor has no Polarity to worry about? Ie which way around?
@jeffharrell1874 Жыл бұрын
That is correct. Either orientation will work.
@EverH0p3 Жыл бұрын
@@jeffharrell1874 Thanks Jeff. Im actually wanting to do this for a 1998 V6 camry but the part number is different to the one you provide and no longer available. Your part is the same except its 47pF and the original 30pF. I was wondering if your part would work as a substitute. Any ideas?
@jeffharrell1874 Жыл бұрын
@@EverH0p3 I’ve heard success from others in all parts listed in description 👍🏿
@kyzercube Жыл бұрын
This one is the easier of the 2 3.0L models of 99-03. I have the harder one that's in the Avalons ( 06/2000 manufacture date ). A youtuber ( can't remember what channel ) did a genius workaround by replacing the bolt with a stud of equal thread type and applying lock-tight so it would not come out easily, then poking the stud through the hole of that " bracket " thing and using a nut to tighten it down. This makes it so instead of fighting a bolt every turn with a wrench, you just have to break the nut loose with a single turn and hand loosen it the rest of the way. Also you're not fighting to reinstall it.
@hehunches Жыл бұрын
I wish I had a code book, sick dude
@jeffharrell1874 Жыл бұрын
These code explanations can be found in a Haynes repair manual.
@hehunches Жыл бұрын
(0:30) Connect E1 to TC with a paperclip (0:48) check dash with paperclip in (6:25) Brake pedal 8 times while ignition on ACC
@craigkennedy5328 Жыл бұрын
Hi Jeff. Just wondering if the resonator needs to go in one orientation or does it not matter? I have a 98 Camry that has rare intermittent issues with the Speedo dropping to zero when driving. Car still goes OK while moving but OD OFF light comes on and sometimes there are auto shift issues up changing from a stop start. I’ll try your repair recommendation. Thanks for posting. Kind regards. Craig
@jeffharrell1874 Жыл бұрын
The orientation doesn’t matter. It should work no matter how it goes in.
@craigkennedy5328 Жыл бұрын
Thanks Jeff. I replaced the speed sensor to fix a transmission fault breakdown a few years ago. The 98 Camry 2.2L has been mostly OK since then except for the occasional speedo zeroing while driving, check engine light ON, OD OFF light ON and sometimes not changing up from first to second gear. The error seems to resolve itself after about 15-60 seconds but I’m concerned about unresponsiveness especially in traffic. So it’s potentially a safety concern I think. I was thinking the issue could be a faulty/sticky 1-2 shift solenoid but it changes sometimes even when I get the speedo fault. I’ve ordered the ceramic resonator and will replace once received and let you know. You’ve posted such helpful advice. Thanks again! Craig
@craigkennedy5328 Жыл бұрын
Forgot to mention, I checked and found no error codes today even after the speedo zero fault occurred last night. The check engine light comes ON during the fault but then goes OFF presumably when the fault resolves itself.
@craigkennedy5328 Жыл бұрын
Just finished replacing the ceramic resonator with a new one. Test drive was fine. Smooth shifting. Will monitor over next few months and let you know how it goes. I suspect this should eliminate the intermittent random speedo drop out noticed every now and then from my 98 Camry 4 cylinder.
@craigkennedy532819 күн бұрын
Hi Jeff. FYI. Been a year after changing the cluster resonator in my 98 Camry but unfortunately, I still have the same issue. I think the issue is getting more frequent and it seems to occur in moist/rainy weather. I’ve ordered an aftermarket speed sensor and will see if that solves the intermittent issue. Failing that, ECU or wiring will investigated. Regards, Craig
@mojamski Жыл бұрын
Great video. Would this be the same for a 98 Sienna you think? Sure hope so just got the doggone ABS light this morning. Where did you come by that procedure? Just curious... :)
@jeffharrell1874 Жыл бұрын
I believe it should work for that sienna, though the location of the DLC connector may be in a different spot around the engine. I found this procedure in a Haynes repair manual as well as other online videos. But the other videos were not all that clear, so I thought putting this video out may help many others going through the same issue.
@user-2uf2kr2c Жыл бұрын
Hello, the datalink connector is the obd connector? I want to try this on a toyota ipsum. Regards
@jeffharrell1874 Жыл бұрын
No. This data link connector is in addition to the OBD connector under the steering wheel.
@user-2uf2kr2c Жыл бұрын
@@jeffharrell1874 Ok, so in the ipsum they're under the steering wheel?
@user-2uf2kr2c Жыл бұрын
Is this connector specifically for your brakes/abs? Regards
@jeffharrell1874 Жыл бұрын
@@user-2uf2kr2c as far as I know for the 97-01 models, this fix is done with the connections inside the engine bay. On the 2002 models and up, i believe It can only be done using the OBD connection under the steering wheel. And to answer your other question, those specific connections that were touching the jump wire should only tap into the abs system. My knowledge is limited beyond that.
Пікірлер
I found this video a couple years ago when having this issue with my JDM Camry Gracia and couldnt find the issue with all sensors sending and reading properly, so I got the resonator and all to do this repair, but never bothered to replace it because I'm lazy. It finally conked fully out this week, just replaced that resonator and BOOM everything is perfect again. You are a godsend with this video my man, if it wasn't for this, I'd probably still be losing my mind trying to find out what's wrong.
Where do I get ur book for the Toyota I’m trying to get one for the 1997 hilux surf
I bought a Haynes repair manual I found on eBay used. I believe Haynes only published vehicles for the US. You might find the info you need from a Haynes 1997 4-Runner manual.
Had all three issues, emphasis on "had" but not any more thanks for the video. Mine is a 1997 Toyota Camry XLE 2.2L for reference.
Hi Jeff. Any idea whether this solution works for a 2004 Lexus GX470? There seems to be a common scenario for that vehicle where the speedometer is stuck at 0 but the odometer continues to function (and thankfully the transmission shifting also behaves itself) which is of course different to the 3 symptoms you've described. I'd give it a try only I have to order the part first and without having taken out the cluster yet I can't site the component to make sure it is the same value - so I guess my first question is do you know if the component is the same for that model vehicle? Or anyone able to direct me to a circuit diagram (or photo even) for the GX470 speedo itself?
You might have a speed sensor issue. I don’t think your root cause is the same as in this video.
I was able to fix it on my 1998 Toyota Camry thanks to your Instructions - I'm driving proud now and the chicks dig my car!...Lol - Thanks!
After 2 speed sensors and checking for loose fuses I jumped on KZread to find this and similar videos. Thanks Question? Soldering the blue ceramic resistor on the opposite side? Does that interfere with assembly? Seems it could.
It does not, and it makes it so much easier. Good luck!
My speedometer works good, but my odometer doesn’t show all numbers, if my tundra has 123,467 miles it shows 1 3,46 incomplete does this fix this issue ? I don’t want to buy a new cluster just for that
I’m not sure if this helps in your case.
Amazing video, appreciate a lot!
Worked!! Thank you for the easy fix!
Can the place be put onto the front, replacing the old one?
After removing the bad capacitor, the new one can be installed on either side of the electronic board. But it’s much easier to install through the back.
I just replaced the instrument cluster on my 4Runner since the last had a broken screen. Everything seems good except the odometer is blank. Trip A and Trip B both work. Any ideas? TIA.
If your speedometer is still working, this may be a different issue within the instrument cluster. I’m not sure what that would be.
How do you put the tube seals in?
There’s multiple ways, depending on what tools you have available. It’s possible to use just a hammer or mallet alone to lightly tap them in. I’ve heard of people using a socket or pvc piece of the same diameter of the seals to help evenly apply force on the seal to help it fully seat in place. If I remember correctly, I think I only used a small hammer to carefully tap all around the seal. It’s not the easiest method, but it’s better than hammering against a flat head screw driver which could slip out of place and cut through your seal. I made that mistake and had to buy another set of tube seals lol.
This is by far the best video for this job! Pain in the butt process and solidifies my hate for front wheel drive cars. So much easier on a RWD car! 😡
Nine didn't blink fast or anything. It kept giving me code 33 on my 1997 toyota 4runner any other way to clear it?
Have you already changed the abs/speed sensor for that wheel?
@@jeffharrell1874 yes
@@damacknificent151 it’s possible that some variation of the number of brake pedal presses may help clear the code if the part swap was a success. If that doesn’t work, then it may be necessary to use a special scan tool that can recognize Toyota abs codes, or further diagnosis from a mechanic.
Yes this worked! I changed my front driver's side cv shaft and hub and bearing! It ended up being just metal fillings on abs wheel speed sensor! Just clean it up ... Did your rest method. Vala
Where did you get the resonator? Never did hear you give the site to get it.
Look in the video description. You’ll find some links.
Does this method work for 97 toyota camry 4 cylinder? or does it have to be 6 cylinder?
I believe it should work either way
Awesome..Thanks! Found a new hatch handle on Amazon for $12.
It's a good video without all the fanfare, bells, and whistles. No excessive rambling or camera jerking. Thanks for the fix!
What is the link to get the part if u will can u send it to me
There should several link options in the video description.
Be prepared for the outer cover clips to break. You can buy an assortment of different size clips online for cheap.
Thank for sharing! Is it possible for you to share toyota camry third gen. problem?
Hello , Jeff , thank you for responding. basically . I was changing a sparkplug of a V 6 Rx 300 0f '01. the sleeve of sparkplug at the back ,broke off where the hard palstic , about 1/2 inch. I have the sparkplug out . I did everything possible to pull it out . after lubricaring with silicon , it doesn't even turn . I was thinking of drilling it to pieces, and after that , vacuum inside . will it work? Thanks.
It’s hard for me to picture what you have going on. I would get a knowledgeable mechanic friend to take a look or send him pictures of your current situation, then see what he advises to do. You don’t want to do anything that could cause any pieces to fall through the spark plug hole and into the engine.
You are a gangster!
hello, with th 6.75 ft/lbs torque on your valve cover i can still see the the gasket , I used the blue gasket and its visible within the gap . that is supposed to be?
It’s possible you may see the gasket slightly. Confession: I did not use a torque wrench to tighten mine. I did it just by feel, but be careful not to do it too tight or you could break a bolt or thread (which I’ve done before 😬)
I’m seeing the gasket on mine too. I only did the front cover so far. Seems like a huge gap but I torqued to spec. Any leaks? Doing rear valve cover tomorrow and hope I didn’t screw up
Thanks for the video brother.
Thank you, you described exactly what I’m experiencing with my 99 Camry.
Thank you so much for taking the time to make this and help others out. My abs light came on and I tried several different scan tools, including one I was told cost more than my car. The paper clip gave me the only accurate diagnosis. Two wheels sensors later the ABS light turned right off and I'm back in business with the ABS working perfect once again. Thank you again and God Bless.
My speedometer sits at 0 but odometer stays at 147k and I get the erratic shifting. CEL code P0500. Do you think its the speed sensor on the bell housing or the blue resonator in the cluster?
It’s sounding like the resonator. Worth a shot for only about $5 and some time.
Does the tach also have a ceramic resonator? My Speedo and tach are both acting up!
Did this and it screwed up my speedometer more. Have to get a new one.
I have the exact problem...97 Lexus ES300😢 but I can't find a ceramic resonator for it...help please...display the link ...🙏 ( I already replaced both speed sensors) major tune up 😂 and nothing & Reset the speedometer / cluster
The link is displayed in the video description.
Thanks for the video that fixed the issues and got it back on the road.
This is the gift that keeps on giving. Very similar presentation 1998 Toyota Sienna with 244K miles. When hot day (we are in Texas) there is no odometer display or speedometer operation. On cool mornings it works fine and is a happy camper. This has been so frustrating. Your technique for soldering is novel but very acceptable. This video was very well done and your documentation is extremely solid. I will report back success / failure after part(s) arrive and procedure completed. Again, thank you so much for the very excellent video.
Good luck! I think it’s worth every effort to keep these Toyotas on the road. They are so well made!
Thank you so much. It worked for 99 camry
I put the same part Digi Key 490-18260-ND into my 99 Avalon and it cooked the speedometer board. After carefully soldering the part to speedometer, I immediately smelled electrical issue when on turning on the ignition. I removed the speedometer to see the board had a burn on it. Doing a continuity test on my newly soldered connection posts (3) there was no problem between them, no short. This is a similar "replacement part" to the original part suggested in another video that is no longer available PN # x902-ND - maybe the problem? I've bought a used cluster to install. Best to ya's, God Bless...
Awesome video I like how short it is and very helpful !
Can someone please tell me if this will work on my 1998 Lexus LX 470? Thanks
What symptoms are you having?
Tried this today on my 97 Lexus es300. And my car is still not allowing the speedometer to work. I'm guessing the next step is purchase an entirely different cluster panel.🤦♀️
Was your odometer not working before as well?
Informative, thanks! Your volume is very low, the ads are 10 times louder.
Agreed. Volume isn’t good. KZread newbie here 😂
@@jeffharrell1874 haha, I don't know much about doing videos, I just know how to vol adjust in my Filmora lol . I see you have two more vids related, to the Rx300, I wish you had 30, great job on this video. I just bought a 2001, not too many issues right now, just trying to learn my way around it , so I'll be able to handle future issues. I had to take off my rear wiper, as I'm in the middle of the rear window replacement, it is a substantial project.
00:09 Recommended wiper-arm removal? I had to use a mechanical puller, not sure if twisting the motor around like that is ok and why that even helped in the removal..shrugs.. Is this in 'a' manual, or it just worked for you?
No manual was used for this process. Turning it allowed me to position it in a way to relieve the tension so that it could be pulled off easily. Motor was not harmed.
So helpful nice one !!!!
Thank you for this video. You saved me time, money, and knuckle busting frustration. Easy fix on 99 RX300. (280,000+ miles)
Me too, mine isn't broken, but I wanted to know how to access parts back there. Really good video.
Great stuff! So the resistor has no Polarity to worry about? Ie which way around?
That is correct. Either orientation will work.
@@jeffharrell1874 Thanks Jeff. Im actually wanting to do this for a 1998 V6 camry but the part number is different to the one you provide and no longer available. Your part is the same except its 47pF and the original 30pF. I was wondering if your part would work as a substitute. Any ideas?
@@EverH0p3 I’ve heard success from others in all parts listed in description 👍🏿
This one is the easier of the 2 3.0L models of 99-03. I have the harder one that's in the Avalons ( 06/2000 manufacture date ). A youtuber ( can't remember what channel ) did a genius workaround by replacing the bolt with a stud of equal thread type and applying lock-tight so it would not come out easily, then poking the stud through the hole of that " bracket " thing and using a nut to tighten it down. This makes it so instead of fighting a bolt every turn with a wrench, you just have to break the nut loose with a single turn and hand loosen it the rest of the way. Also you're not fighting to reinstall it.
I wish I had a code book, sick dude
These code explanations can be found in a Haynes repair manual.
(0:30) Connect E1 to TC with a paperclip (0:48) check dash with paperclip in (6:25) Brake pedal 8 times while ignition on ACC
Hi Jeff. Just wondering if the resonator needs to go in one orientation or does it not matter? I have a 98 Camry that has rare intermittent issues with the Speedo dropping to zero when driving. Car still goes OK while moving but OD OFF light comes on and sometimes there are auto shift issues up changing from a stop start. I’ll try your repair recommendation. Thanks for posting. Kind regards. Craig
The orientation doesn’t matter. It should work no matter how it goes in.
Thanks Jeff. I replaced the speed sensor to fix a transmission fault breakdown a few years ago. The 98 Camry 2.2L has been mostly OK since then except for the occasional speedo zeroing while driving, check engine light ON, OD OFF light ON and sometimes not changing up from first to second gear. The error seems to resolve itself after about 15-60 seconds but I’m concerned about unresponsiveness especially in traffic. So it’s potentially a safety concern I think. I was thinking the issue could be a faulty/sticky 1-2 shift solenoid but it changes sometimes even when I get the speedo fault. I’ve ordered the ceramic resonator and will replace once received and let you know. You’ve posted such helpful advice. Thanks again! Craig
Forgot to mention, I checked and found no error codes today even after the speedo zero fault occurred last night. The check engine light comes ON during the fault but then goes OFF presumably when the fault resolves itself.
Just finished replacing the ceramic resonator with a new one. Test drive was fine. Smooth shifting. Will monitor over next few months and let you know how it goes. I suspect this should eliminate the intermittent random speedo drop out noticed every now and then from my 98 Camry 4 cylinder.
Hi Jeff. FYI. Been a year after changing the cluster resonator in my 98 Camry but unfortunately, I still have the same issue. I think the issue is getting more frequent and it seems to occur in moist/rainy weather. I’ve ordered an aftermarket speed sensor and will see if that solves the intermittent issue. Failing that, ECU or wiring will investigated. Regards, Craig
Great video. Would this be the same for a 98 Sienna you think? Sure hope so just got the doggone ABS light this morning. Where did you come by that procedure? Just curious... :)
I believe it should work for that sienna, though the location of the DLC connector may be in a different spot around the engine. I found this procedure in a Haynes repair manual as well as other online videos. But the other videos were not all that clear, so I thought putting this video out may help many others going through the same issue.
Hello, the datalink connector is the obd connector? I want to try this on a toyota ipsum. Regards
No. This data link connector is in addition to the OBD connector under the steering wheel.
@@jeffharrell1874 Ok, so in the ipsum they're under the steering wheel?
Is this connector specifically for your brakes/abs? Regards
@@user-2uf2kr2c as far as I know for the 97-01 models, this fix is done with the connections inside the engine bay. On the 2002 models and up, i believe It can only be done using the OBD connection under the steering wheel. And to answer your other question, those specific connections that were touching the jump wire should only tap into the abs system. My knowledge is limited beyond that.
Ok thanks. Godbless