an obvious backyard mokanic,,,its so easy doing it the right way
@juantabullo3126Ай бұрын
I was under the impression that the plastic part also takes gasket sealant...? Or only the metal parts boat at thermostat cover?
@PortCanaveralFloridaАй бұрын
Only the metal side.
@PortCanaveralFlorida2 ай бұрын
NOTE TO EVERYONE - This problem was the AMP in the trunk right side, not the head unit, found one in a junk yard for $50, works perfect!
@ZackeryElmhorst2 ай бұрын
Can you do a follow up video on what you’re referring to?
@shawnhatley6372Ай бұрын
Which amp did you buy
@PortCanaveralFlorida29 күн бұрын
@shawnhatley6372 stock amp of a 2013, tho my car is a 2012
@paulsanchez3142 ай бұрын
Did you also lose the controls on the steering wheel
@PortCanaveralFlorida2 ай бұрын
No, still using just my phone for music.
@luffykillua21994 ай бұрын
The only thing I have to do is solder the wires then I’ll have my mechanic do it if he messes it up he owes me a new back up camera gps n antenna
@Walruse-memez6 ай бұрын
Can’t remember where, but the original stock GPS is a similar dongle that I found somewhere hidden on the drivers side but still external enough to function. Can just use that spot? Unfortunately the stock Nav/rear cam don’t seem to be compatible with any new modules. But these units effectively replace them and their OG functionality. Try Crutchfield, they can do the wiring for you with connectors to the original cabling. Essentially plug/play for you to install. Also custom instructions available. It’s the best option I’ve found, but they don’t ship internationally which sucks for me in Australia.
@tomnyboy09168 ай бұрын
You can still use this unit but you will need an interface to use all of the features… fortunately enough I have a ‘13 GLS and the unit was in fact plug and play for me
@PortCanaveralFlorida8 ай бұрын
What interface would that be?
@Q13207 ай бұрын
All these opinions and no solutions, what is the harness and or module to make this plug and play, because to do this it's about ,800 USD and you need a new head unit and a 350usd module which is also the same cost as a head unit cool
@bbulliard8 ай бұрын
best advice to prevent! keep your tank 100% full
@jianqinlin39788 ай бұрын
Do u find one yet?
@PortCanaveralFlorida8 ай бұрын
Check @curiosity2314 comment. I'm looking into this.
@TonoXX75 ай бұрын
hello there, i have a 2013 Elantra but is the Coupe version with the same navigation as the limited! so i have the same problem! please if you manage to solve this i want to know! thank you!@@PortCanaveralFlorida
@PortCanaveralFlorida2 ай бұрын
It was the AMP all along.
@shawnhatley6372Ай бұрын
What kind of amp did you get?
@PortCanaveralFloridaАй бұрын
@shawnhatley6372 just a stock amp from a part-out vehicle, works perfect!
@curiosity23149 ай бұрын
It is not inexpensive but on my Ford Focus 2007 I went with the Sony XAV-9000ES and in my wife's Elantra 2014 the Sony XAV-AX6000, Crutchfield sells all the wiring you need to build yourself or they also sell it plug and play. Although it is not needed I did purchase the XM receivers separately so they are there for future use if needed. I keep my automobiles a long time so I have no issue with spending on a good upgrade here and there. They both run and drive like new and the Elantra got a new engine last year by Hyundai due to the piston slap issues these engines were having because of poor QC at the time. When it comes to automotive radios Sony is Sony, it works. The Ford had a Sony XAV-701HD since 2013, zero issues just became outdated but can be repurposed.
@PortCanaveralFlorida9 ай бұрын
So much appreciated!!! Others too here will be checking this Sony out... thank you so much!!
@mikecarr28709 ай бұрын
Thank you
@axed19299 ай бұрын
I drilled three 5mm pilot holes, eventually taking them out to 12mm to get a socket on the bolts them once finished i siliconed in rubber grommets. Worked well, looks good.
@moefakhoury647811 ай бұрын
My 2012 Hyundai Elantra Limited comes equipped with a factory backup camera, but it has a radio. Very odd to me and im not sure as to why. Any ideas?
@PortCanaveralFlorida11 ай бұрын
The limited versions can come completely loaded or parchely loaded.
@user-fd1wc9ct4k Жыл бұрын
Hey so if you sent this one back can you provide a link or video of the one you have now ? Compatible with the Hyundai elantra limited 2012
@PortCanaveralFlorida Жыл бұрын
I put the stock unit back in which does not work. And I've been using my phone an Anker Soundcore Bluetooth Speaker. I have yet to see a plug in play unit for the Elantra Limited Without Frankensteining your car. If there's someone out there that has done this, please post the link for everyone to see.
@loganwolf3150 Жыл бұрын
did your speakers work at all? i plugged my speakers in and go no audio from them
@PortCanaveralFlorida Жыл бұрын
I looked at what came in the package, cables, etc. The only match up/plug n play were the connections to the amp/speakers. No plug n play with backup cam, antenna, or gps.
@loganwolf3150 Жыл бұрын
@@PortCanaveralFloridaalright. it’s weird because when i plug mine to the speakers, i get no sound from the speakers at all. idk what i need to do to make sound come out
@PortCanaveralFlorida Жыл бұрын
@loganwolf3150 check your amp make sure it's working
@shawnhatley6372 Жыл бұрын
Same here did you found out why no sound because my 2011 is doing the same thing
@shawnhatley6372 Жыл бұрын
Any update on this stereo sound not working
@Little.Bow.Big.Crybaby Жыл бұрын
DO NOT DO THIS!!! YOU CAN REPLACE THE THERMOSTAT WITHOUT CUTTING YOUR FRAME OR REMOVING POWER HEAD. I JUST DID MINE WITHOUT CUTTING OR DRILLING HOLES.
@PortCanaveralFlorida Жыл бұрын
Thanks for the comment. The chance of broken bolts is SUPER common. This is very easy to do and get back on the water, hurts nothing, a little JB weld, paint if you choose and your done.
@stevencovington9508 Жыл бұрын
I just ran into the same issue on my 2015 Limited Elantra. Did you find a fix or work around?
@PortCanaveralFlorida Жыл бұрын
No plug n and play w/ stock features.
@PortCanaveralFlorida2 ай бұрын
It was the AMP all along.
@Johnfor3 Жыл бұрын
What engineer thought this design would be ok! Why on earth wouldn't they have added some kind of assess panel at the very least!
@Captobvious23 Жыл бұрын
Looks like you need a canbus cable box for the steering wheel backup camera and equip amplifier
@PortCanaveralFlorida Жыл бұрын
Thanks r b I'll check into this!
@xposhr Жыл бұрын
You can use what's there without cutting. Would just require you look at the wiring diagram and pin out to the ones you need.
@PortCanaveralFlorida Жыл бұрын
Have you looked at the diagram? Not much of one. If you've done this install please post.
@ploesti1943 Жыл бұрын
Can you post a link on how to do that ?
@iam_rockcity Жыл бұрын
My limited didn’t come with a backup cam so this might work for me.
@PortCanaveralFlorida Жыл бұрын
Yes, tho if you have the GPS you'll have that little hockey puck to deal with.
@mikemolino7150 Жыл бұрын
Were you able to find a unit that worked with the limited edition? I have a 2013 limited Elantra and wanted to upgrade but reuse the factory camera and wiring.
@PortCanaveralFlorida Жыл бұрын
Not at the moment I'm waiting on people from KZread to send me some information I definitely didn't want to Frankenstein my car
@mikemolino7150 Жыл бұрын
In my research, I’m told this will work with the factory camera. The camera wiring is in the factory harness
@PortCanaveralFlorida Жыл бұрын
@@mikemolino7150 What about the backup wire ( to trigger the camera) and gps?
@mikemolino7150 Жыл бұрын
Not sure about the trigger wire. It’s in the harness also. I think it would just work through their harness conversion. GPS won’t work though but I think you could bury their gps behind the radio so it’s not in sight. I’m still emailing with them.
@PortCanaveralFlorida Жыл бұрын
@Mike Molino ,thanks Mike. Post a vid of the completed install, I'll follow, I didn't get much cooperation with the seller. Keep me posted!
@deanfletcher8284 Жыл бұрын
This worked like a charm. My issue was old gas, not water in the tank. I siphoned about 10 gallons when the stream slowed to a trickle, then I realized I had to loosen the gas cap to relieve the vacuum. To answer one question below, once you pump the bulb, gravity takes over, so you do not need to keep pumping the bulb to keep the flow going. Great video.
@q1o2 Жыл бұрын
Good video!
@AllBrevard Жыл бұрын
Nice production and messages. It's a year later, are things better? Elon rocks.
@PortCanaveralFlorida Жыл бұрын
Thanks, I'm sure the community would say it's just fine here without more hands getting into our pockets and yes, Elon's TEAM ROCKS!
@dossary912 жыл бұрын
I like the way you did it thank you for very nice video it help me .
@chucklz7572 жыл бұрын
that was awesome man!
@aspenrebel2 жыл бұрын
I came up with an easier way than that. I got a 1" cylinder type drill bit. drilled (2) 1" holes in line with the 2 end bolts of the thermostat, so I could easily take the screws in-and-out. then I filled in the holes by cementing in 1" dia black rubber grommets, which had a groove around edge. The only problem was the metal was thicker than the groove opening. But still made it work with a lot of waterproof marine cement. Bought an extra pair of grommets just in case, to keep on hand.
@rubengonzalez8399 Жыл бұрын
What about the middle bolt?
@aspenrebel Жыл бұрын
@@rubengonzalez8399 the middle bolt I could get out no problem. It was just the two end bolts.
@karlmroch33942 жыл бұрын
Amazing thank you brother, enjoy the water !!
@joyned12 жыл бұрын
No criticism from me but I should point out that the cork gaskets should sit on top of the thermostats. They are the last piece of the puzzle before the final body gasket which in the video is already attached to the engine body. It probably doesn’t make a difference but that is how it is installed on my original untouched 1979 85 hp v4 evinrude, basically it is still the same engine and I am using the same thermostat kit.
@PortCanaveralFlorida2 жыл бұрын
Looking at the diagram now that you drought it up, they sit under the stat.
@joyned12 жыл бұрын
It looks that way in the diagram but the original body gaskets covering the cork washers were made of a thin metal (not like today’s paper gaskets). They were stamped with an indentation that only allowed the cork washers to be assembled on top.
@PortCanaveralFlorida2 жыл бұрын
@@joyned1 what can I say, its still running just fine. It's, do you like your cheese on top of the burger or at the bottom.
@bilnitro2 жыл бұрын
Got to love Ski Island
@PortCanaveralFlorida2 жыл бұрын
Its pretty much gone
@davidclements32522 жыл бұрын
this video was a big help for me on my 1979 100 HP Johnson Javelin, thanks for the video!!
@jeffreyjavier85512 жыл бұрын
That’s Awesome Thanks
@dgage17762 жыл бұрын
Sweet! Just bought a nice bass boat for 500 bucks. The guy replaced everything in the ignition system and just could not figure it out. Just water in the tank! I figured that out because it runs fine below freezing
@robertpapp962 жыл бұрын
Geez... poor motor.. Perfectly unnessesery that cut... just need right tools, and some knowledge.. I can imagine how these people do other "fixing"..
@darrellladnier11392 жыл бұрын
I use bored holes in front of 2 end bolts for socket removed bolts .put rubber plugs in holes easy to do.
@SemperParatus12342 жыл бұрын
Usually there is an o-ring on the bottom of the fill cap. Replace when bad and lube it with a bit of grease to maintain seal
@dryoatmeal982 жыл бұрын
I found water in my boat gas tank, luckily I was on 1/4 of a tank. I gave this method a try and pumped until empty. 11 gallons in less than an hour. Worked well, thanks!
@twistygrip41802 жыл бұрын
That was awesome!!!!! What great timing!!! 👊😎
@derekrivchin38942 жыл бұрын
No shit. Thanks for wasting 5 min
@midnightrunner684 Жыл бұрын
M.A.G.A ?
@JimTMcDaniels13 жыл бұрын
Thank you sharing how you have found to make this job doable. Let me add: ONCE AGAIN, a Video involving the possibility of BREAKING Bolts that when you are dealing with such bolts that you must remove: If the bolt feels like it may break at all, they are full of corrosion crud. So don't break it, do this instead: you must give it patience and slight back and forth movement to work it out, the corrosion will fall out: So try to tighten it just something of a move, then try to looses in just something. Then repeat and repeat and repeat. So a rocking motion of back and forth without putting too much force in either direction where it may over stress the bolt and break it off. As you continue, if your observant enough, you may even see little sands of corrosion dropping out of bottom of the bolt as you do this. And that the bolt is able to move more than it did. Now you can't loose once you have some movement. Because if you are patient and keep only rocking the bolt back and forth back and forth, more corrosion will come out and the bolt will move even more from tight to loose. Of course also spray penetrating oil into the threads as you can and walk away and come back after soaking. Take care
@bbulliard3 жыл бұрын
the fuel line intake in the tank is 1/2" from the bottom, so this will leave 1/2" of water in the tank. best to remove the fuel sending unit and siphon with a fuel pump from the bottom to completely remove and always keep tank full
@bbulliard8 ай бұрын
you are correct sir. this method only removes to the level of the fuel line.
@ct17623 жыл бұрын
just so everyone that does this is aware: he use the wrong sealant and didn't apply it to BOTH sides of the gasket. do it this way, and it will leak at some point down the road. the factory service manual says OMC gasket sealing compound on BOTH gaskets, front and back. the sealer doesn't effect the pressure relief valves because there is a huge hole in the gasket, and if you get a tiny bit on the t stats... so what? they just need to open to bring water in.they don't get unseated like other models at higher pressure. OMC gasket sealer doesn't harden either, so completely harmless.
@PortCanaveralFlorida3 жыл бұрын
It's 2021, I posted that in 2015 and it's still holding. Thanks for your input.
@davidtimmins8701 Жыл бұрын
I Jane the exact motor. What part number did you used to order the proper parts? Thanks
@HiTechDiver3 жыл бұрын
The big problem I see is that the fuel pick up tubes don't go all the way to the bottom of the tank; at least not in mine. My guess is that it prevents any sediment, that settles to the bottom, from being drawn up in the fuel line. Being that water is heavier than fuel, if there is water in the tank, there may still be water remaining in the tank below the level of what the pickup tubes will reach; problem not solved.
@po58323 жыл бұрын
Gas MELTS PLASTIC!!! PLEASE USE APPROVED GAS CONTAINERS!! Unless you like idea of picking up jug and having a gallon of gas spilled when the bottom falls off the jug
@PortCanaveralFlorida3 жыл бұрын
It wasn't in the jug for weeks on end, just for the demonstration.
@YeeYee.Living3 жыл бұрын
Biden MosT PoPuLar PreSiDEnt
@baconburgeronly30893 жыл бұрын
Well must hes in the White House so
@bobito23903 жыл бұрын
Let's party and celebrate stupid old corrupt Trump, people!!!!!!
@bobito23903 жыл бұрын
QAnus says TRump won
@rajnbull3 жыл бұрын
and you mean to tell me that Trump lost to this old man that's in office now with all these supporters!
@PortCanaveralFlorida3 жыл бұрын
Nope, might be called political rigging.
@baconburgeronly30893 жыл бұрын
Yes shows how pathetic he truly is I mean how do you lose to biden
@cuocsongmy20083 жыл бұрын
Hello all MAGA patriots. Please tell me where in Florida I could join Trump's rallies? I want to join but I don't know where.
@baconburgeronly30893 жыл бұрын
Go at your own risk I here thier to woke for thier own good
Пікірлер
an obvious backyard mokanic,,,its so easy doing it the right way
I was under the impression that the plastic part also takes gasket sealant...? Or only the metal parts boat at thermostat cover?
Only the metal side.
NOTE TO EVERYONE - This problem was the AMP in the trunk right side, not the head unit, found one in a junk yard for $50, works perfect!
Can you do a follow up video on what you’re referring to?
Which amp did you buy
@shawnhatley6372 stock amp of a 2013, tho my car is a 2012
Did you also lose the controls on the steering wheel
No, still using just my phone for music.
The only thing I have to do is solder the wires then I’ll have my mechanic do it if he messes it up he owes me a new back up camera gps n antenna
Can’t remember where, but the original stock GPS is a similar dongle that I found somewhere hidden on the drivers side but still external enough to function. Can just use that spot? Unfortunately the stock Nav/rear cam don’t seem to be compatible with any new modules. But these units effectively replace them and their OG functionality. Try Crutchfield, they can do the wiring for you with connectors to the original cabling. Essentially plug/play for you to install. Also custom instructions available. It’s the best option I’ve found, but they don’t ship internationally which sucks for me in Australia.
You can still use this unit but you will need an interface to use all of the features… fortunately enough I have a ‘13 GLS and the unit was in fact plug and play for me
What interface would that be?
All these opinions and no solutions, what is the harness and or module to make this plug and play, because to do this it's about ,800 USD and you need a new head unit and a 350usd module which is also the same cost as a head unit cool
best advice to prevent! keep your tank 100% full
Do u find one yet?
Check @curiosity2314 comment. I'm looking into this.
hello there, i have a 2013 Elantra but is the Coupe version with the same navigation as the limited! so i have the same problem! please if you manage to solve this i want to know! thank you!@@PortCanaveralFlorida
It was the AMP all along.
What kind of amp did you get?
@shawnhatley6372 just a stock amp from a part-out vehicle, works perfect!
It is not inexpensive but on my Ford Focus 2007 I went with the Sony XAV-9000ES and in my wife's Elantra 2014 the Sony XAV-AX6000, Crutchfield sells all the wiring you need to build yourself or they also sell it plug and play. Although it is not needed I did purchase the XM receivers separately so they are there for future use if needed. I keep my automobiles a long time so I have no issue with spending on a good upgrade here and there. They both run and drive like new and the Elantra got a new engine last year by Hyundai due to the piston slap issues these engines were having because of poor QC at the time. When it comes to automotive radios Sony is Sony, it works. The Ford had a Sony XAV-701HD since 2013, zero issues just became outdated but can be repurposed.
So much appreciated!!! Others too here will be checking this Sony out... thank you so much!!
Thank you
I drilled three 5mm pilot holes, eventually taking them out to 12mm to get a socket on the bolts them once finished i siliconed in rubber grommets. Worked well, looks good.
My 2012 Hyundai Elantra Limited comes equipped with a factory backup camera, but it has a radio. Very odd to me and im not sure as to why. Any ideas?
The limited versions can come completely loaded or parchely loaded.
Hey so if you sent this one back can you provide a link or video of the one you have now ? Compatible with the Hyundai elantra limited 2012
I put the stock unit back in which does not work. And I've been using my phone an Anker Soundcore Bluetooth Speaker. I have yet to see a plug in play unit for the Elantra Limited Without Frankensteining your car. If there's someone out there that has done this, please post the link for everyone to see.
did your speakers work at all? i plugged my speakers in and go no audio from them
I looked at what came in the package, cables, etc. The only match up/plug n play were the connections to the amp/speakers. No plug n play with backup cam, antenna, or gps.
@@PortCanaveralFloridaalright. it’s weird because when i plug mine to the speakers, i get no sound from the speakers at all. idk what i need to do to make sound come out
@loganwolf3150 check your amp make sure it's working
Same here did you found out why no sound because my 2011 is doing the same thing
Any update on this stereo sound not working
DO NOT DO THIS!!! YOU CAN REPLACE THE THERMOSTAT WITHOUT CUTTING YOUR FRAME OR REMOVING POWER HEAD. I JUST DID MINE WITHOUT CUTTING OR DRILLING HOLES.
Thanks for the comment. The chance of broken bolts is SUPER common. This is very easy to do and get back on the water, hurts nothing, a little JB weld, paint if you choose and your done.
I just ran into the same issue on my 2015 Limited Elantra. Did you find a fix or work around?
No plug n and play w/ stock features.
It was the AMP all along.
What engineer thought this design would be ok! Why on earth wouldn't they have added some kind of assess panel at the very least!
Looks like you need a canbus cable box for the steering wheel backup camera and equip amplifier
Thanks r b I'll check into this!
You can use what's there without cutting. Would just require you look at the wiring diagram and pin out to the ones you need.
Have you looked at the diagram? Not much of one. If you've done this install please post.
Can you post a link on how to do that ?
My limited didn’t come with a backup cam so this might work for me.
Yes, tho if you have the GPS you'll have that little hockey puck to deal with.
Were you able to find a unit that worked with the limited edition? I have a 2013 limited Elantra and wanted to upgrade but reuse the factory camera and wiring.
Not at the moment I'm waiting on people from KZread to send me some information I definitely didn't want to Frankenstein my car
In my research, I’m told this will work with the factory camera. The camera wiring is in the factory harness
@@mikemolino7150 What about the backup wire ( to trigger the camera) and gps?
Not sure about the trigger wire. It’s in the harness also. I think it would just work through their harness conversion. GPS won’t work though but I think you could bury their gps behind the radio so it’s not in sight. I’m still emailing with them.
@Mike Molino ,thanks Mike. Post a vid of the completed install, I'll follow, I didn't get much cooperation with the seller. Keep me posted!
This worked like a charm. My issue was old gas, not water in the tank. I siphoned about 10 gallons when the stream slowed to a trickle, then I realized I had to loosen the gas cap to relieve the vacuum. To answer one question below, once you pump the bulb, gravity takes over, so you do not need to keep pumping the bulb to keep the flow going. Great video.
Good video!
Nice production and messages. It's a year later, are things better? Elon rocks.
Thanks, I'm sure the community would say it's just fine here without more hands getting into our pockets and yes, Elon's TEAM ROCKS!
I like the way you did it thank you for very nice video it help me .
that was awesome man!
I came up with an easier way than that. I got a 1" cylinder type drill bit. drilled (2) 1" holes in line with the 2 end bolts of the thermostat, so I could easily take the screws in-and-out. then I filled in the holes by cementing in 1" dia black rubber grommets, which had a groove around edge. The only problem was the metal was thicker than the groove opening. But still made it work with a lot of waterproof marine cement. Bought an extra pair of grommets just in case, to keep on hand.
What about the middle bolt?
@@rubengonzalez8399 the middle bolt I could get out no problem. It was just the two end bolts.
Amazing thank you brother, enjoy the water !!
No criticism from me but I should point out that the cork gaskets should sit on top of the thermostats. They are the last piece of the puzzle before the final body gasket which in the video is already attached to the engine body. It probably doesn’t make a difference but that is how it is installed on my original untouched 1979 85 hp v4 evinrude, basically it is still the same engine and I am using the same thermostat kit.
Looking at the diagram now that you drought it up, they sit under the stat.
It looks that way in the diagram but the original body gaskets covering the cork washers were made of a thin metal (not like today’s paper gaskets). They were stamped with an indentation that only allowed the cork washers to be assembled on top.
@@joyned1 what can I say, its still running just fine. It's, do you like your cheese on top of the burger or at the bottom.
Got to love Ski Island
Its pretty much gone
this video was a big help for me on my 1979 100 HP Johnson Javelin, thanks for the video!!
That’s Awesome Thanks
Sweet! Just bought a nice bass boat for 500 bucks. The guy replaced everything in the ignition system and just could not figure it out. Just water in the tank! I figured that out because it runs fine below freezing
Geez... poor motor.. Perfectly unnessesery that cut... just need right tools, and some knowledge.. I can imagine how these people do other "fixing"..
I use bored holes in front of 2 end bolts for socket removed bolts .put rubber plugs in holes easy to do.
Usually there is an o-ring on the bottom of the fill cap. Replace when bad and lube it with a bit of grease to maintain seal
I found water in my boat gas tank, luckily I was on 1/4 of a tank. I gave this method a try and pumped until empty. 11 gallons in less than an hour. Worked well, thanks!
That was awesome!!!!! What great timing!!! 👊😎
No shit. Thanks for wasting 5 min
M.A.G.A ?
Thank you sharing how you have found to make this job doable. Let me add: ONCE AGAIN, a Video involving the possibility of BREAKING Bolts that when you are dealing with such bolts that you must remove: If the bolt feels like it may break at all, they are full of corrosion crud. So don't break it, do this instead: you must give it patience and slight back and forth movement to work it out, the corrosion will fall out: So try to tighten it just something of a move, then try to looses in just something. Then repeat and repeat and repeat. So a rocking motion of back and forth without putting too much force in either direction where it may over stress the bolt and break it off. As you continue, if your observant enough, you may even see little sands of corrosion dropping out of bottom of the bolt as you do this. And that the bolt is able to move more than it did. Now you can't loose once you have some movement. Because if you are patient and keep only rocking the bolt back and forth back and forth, more corrosion will come out and the bolt will move even more from tight to loose. Of course also spray penetrating oil into the threads as you can and walk away and come back after soaking. Take care
the fuel line intake in the tank is 1/2" from the bottom, so this will leave 1/2" of water in the tank. best to remove the fuel sending unit and siphon with a fuel pump from the bottom to completely remove and always keep tank full
you are correct sir. this method only removes to the level of the fuel line.
just so everyone that does this is aware: he use the wrong sealant and didn't apply it to BOTH sides of the gasket. do it this way, and it will leak at some point down the road. the factory service manual says OMC gasket sealing compound on BOTH gaskets, front and back. the sealer doesn't effect the pressure relief valves because there is a huge hole in the gasket, and if you get a tiny bit on the t stats... so what? they just need to open to bring water in.they don't get unseated like other models at higher pressure. OMC gasket sealer doesn't harden either, so completely harmless.
It's 2021, I posted that in 2015 and it's still holding. Thanks for your input.
I Jane the exact motor. What part number did you used to order the proper parts? Thanks
The big problem I see is that the fuel pick up tubes don't go all the way to the bottom of the tank; at least not in mine. My guess is that it prevents any sediment, that settles to the bottom, from being drawn up in the fuel line. Being that water is heavier than fuel, if there is water in the tank, there may still be water remaining in the tank below the level of what the pickup tubes will reach; problem not solved.
Gas MELTS PLASTIC!!! PLEASE USE APPROVED GAS CONTAINERS!! Unless you like idea of picking up jug and having a gallon of gas spilled when the bottom falls off the jug
It wasn't in the jug for weeks on end, just for the demonstration.
Biden MosT PoPuLar PreSiDEnt
Well must hes in the White House so
Let's party and celebrate stupid old corrupt Trump, people!!!!!!
QAnus says TRump won
and you mean to tell me that Trump lost to this old man that's in office now with all these supporters!
Nope, might be called political rigging.
Yes shows how pathetic he truly is I mean how do you lose to biden
Hello all MAGA patriots. Please tell me where in Florida I could join Trump's rallies? I want to join but I don't know where.
Go at your own risk I here thier to woke for thier own good