These guys flew delta way too much. I feel like I'm watching the pre flight boarding video lol. Good video though, I appreciate the info!
@musmantaiq6711 Жыл бұрын
Which bond are you use for bonding of tpu to aluminium
@GallagherCorporation Жыл бұрын
We could get into the specifics if we partner on something.
@ekussachdeva3416 Жыл бұрын
is hand casting / Manual casting good for polyurethane process? or machine casting is better
@GallagherCorporation Жыл бұрын
We would confidently say that using meter-mix machines is the way to go.
@kargunbatur13692 жыл бұрын
Is that Method A or B, which one can i learn?
@wheels.and.wrenches2 жыл бұрын
My offroad tires are 55 to 65
@tigranohanyan33212 жыл бұрын
I used polyester powder coating on metal (stainless steel and steel) as a primer before casting 90A shore polyurethane 2 part resin. It works great. Again, I used just regular white polyester powder coating baked with high temperature. The bond is so strong that It is very hard to remove polyurethane from metal surface.
@GallagherCorporation2 жыл бұрын
Hi Tigran, which polyester powder coating formulation did you try with success? Was it a TGIC polyester or the non -TGIC (or HAA type, also called Primid type)?
@user-cs9mi7vd6c2 жыл бұрын
Good
@pedroinfante71352 жыл бұрын
Nice video. Could you tell us what kind of binder (glue) do you use for attaching the sample in the metal frame? Thank you.
@GallagherCorporation2 жыл бұрын
The metal frame is held together by the bolts. "The preload is maintained during the shear test by four bolts that were tightened down, finger tight, when the sample was compressed."
@wg11592 жыл бұрын
If a Polyurethane to steel bond is purely shear loaded (so no peel), should the surface roughness still be Ra250? And how well does the bond perform on a pure shear application? Application is a PU disc with diameter 500 mm and thickness 150 mm bonded to a steel bottom and top plate under shear load.
@GallagherCorporation Жыл бұрын
Bonding to two surfaces at the same time can be tricky. Reach out to us if you are experiencing failures and we can talk more.
@ganesanmani52102 жыл бұрын
Have you published any technical papers for this method
@GallagherCorporation2 жыл бұрын
Hi Ganesan, just this video. Thanks for watching.
@ganesanmani52102 жыл бұрын
@@GallagherCorporation Thank you for your kind information
@kargunbatur13692 жыл бұрын
What is your bond strength value as N/mm for your polyurethane wheels, i didn't see any information about that in your official site
@GallagherCorporation2 жыл бұрын
Ultimately, the bond strength of our products exceeds the materials strength. The values obtained from bond testing are influenced heavily by the urethane compound. Due to this, two parts cast with different materials can both have exceptional bond, but very different values from our bond test.
@kargunbatur13692 жыл бұрын
@@GallagherCorporation I see, can i ask a question too, according to which standard are you testing the bond strength ?
@makcatchem96142 жыл бұрын
Wish there was more info videos on this before I spend $20
@GallagherCorporation2 жыл бұрын
Try checking out the channel from FinMan Fishing Innovations - kzread.info/dron/pUNFKoHzNcOiECLjkgn1sg.html
@michaelbush2322 Жыл бұрын
I know I first saw this like 5 months ago on a targeted ad on IG, and I just went on YT expecting to see a ton of reviews by people who bought it, and the only thing I could see was paid advertisement. Which isn’t a bad thing, I’ll probably still buy it with fishing about to open up in the North East, but was hoping to see it in action on some rods that it wasn’t paid to out there. Even crappy products have reviews saying stay away but I can’t find it anywhere 😊
@GallagherCorporation Жыл бұрын
On Instagram, go to FinmanFishing, lots of content there
@adeebshamkhi82212 жыл бұрын
Can we use polyurethane for sealing holes in water galvanized steel tanks?
@GallagherCorporation2 жыл бұрын
Hello Adeeb, we mold solid polyurethane elastomers. You should reach out to someone that works in sealants. Thank you.
@waelomer19902 жыл бұрын
i need an article that speaks about shore A95 TPU under long term compression. can any one help?
@GallagherCorporation2 жыл бұрын
Hi @waelomer1990, what do you need to know?
@waelomer19902 жыл бұрын
@@GallagherCorporation I need to determine the behaviour of polyurethane A95 under long term compression for a product I am working on Thank you
@GallagherCorporation2 жыл бұрын
There’s more to it than just durometer. The geometry will play a major role. Head over to our website and contact us there so you can discuss this in more detail with one of our representatives. gallaghercorp.com/contact/ Thank you!
@khandam77093 жыл бұрын
thanks for breaking down PU hardness into easy to understand examples!
@gasmaskdude26873 жыл бұрын
Excellent video! Couple of questions, 1. Does this follow ASTM 4014? was the bonding a cold bonding process? 2. Is the formula for shear modulus 2(F2-F1) /A the same as what was used?
@RichFarago3 жыл бұрын
You mentioned tailored made customized to fit. Do you actually do that or use off the shelf products?
@GallagherCorporation3 жыл бұрын
Hi Rich! Here's the quote - "When we manufacture products for our customers, we tailor our polyurethane’s properties to fit their needs." Yes, we formulate and process the polyurethane chemistry to provide performance parameters that best meet your requirements.
@aaarrh63 жыл бұрын
Very informative, well produced and comprehensive. 👏👍💥
@GallagherCorporation3 жыл бұрын
Thanks! Glad you enjoyed it.
@maksimchernykh3 жыл бұрын
4:30 best wedding ring ever seen
@viniciusoliveirafontes40333 жыл бұрын
You guys should stop making polyurethane and start making educational material. This is one of the best videos I've ever watched, congratulations!
@GallagherCorporation3 жыл бұрын
Thanks for your comment, Vinicius.
@jayantakumarborah3 жыл бұрын
very nice video. Thanks. what are the standard compression set values for EPDM/Silicone/NBR/FKM/CR /NR rubber?
@GallagherCorporation3 жыл бұрын
Thanks for watching! Don't know about those other materials, we're the polyurethane experts!
@GhostPatronYT3 жыл бұрын
I didn't know there was so much theory to my everyday work EZ. Great tutorial 👍
@forrestberg5913 жыл бұрын
Great explanation! Might’ve added the equation for calculating
@AsadUllah-fv1ir3 жыл бұрын
What is only set
@litarea3 жыл бұрын
Super helpful and really well produced vid. Thanks!
@GallagherCorporation3 жыл бұрын
Glad you enjoyed it!
@narasimhachopparapu45344 жыл бұрын
excellent. thank you for the great video. do you have shear test for anisotropic composite to find G12, G23, G13?
@GallagherCorporation3 жыл бұрын
Thanks for watching! And no, we do not.
@DWP-xg2je4 жыл бұрын
Thank you for the video : )
@GallagherCorporation4 жыл бұрын
You're welcome!
@TheCyberHippie4 жыл бұрын
Does tear strength also equate to abrasion resistance?
@GallagherCorporation4 жыл бұрын
Good question. Tear strength is a good INDICATOR of abrasion resistance, but it’s not the whole answer. Other material properties, like rebound, can also play a role. Check out our page on abrasion resistance for more details: gallaghercorp.com/polyurethane-abrasion-resistance/ We find that every abrasion situation brings its own set of unique challenges, so please contact us to discuss your specific application with our engineering team.
@thanveermohamedk.a24374 жыл бұрын
Hello friends, I am working in a grinding wheels production company and we produce various types of grinding wheels. We also produce Resin bonded wheels in which we experience a problem of abrasive resin layer getting slipped of from the metal base(aluminium). Normally for good adhesion of the abrasive layer, we used to create seration on the aluminium body, grit blast it, also we used to apply a layer of primer on the grit blasted area. But still after all the processes are done our abrasive wheel gets slipped of from the metal base. Can you guys suggest me any good idea how to overcome this issue.
@GallagherCorporation4 жыл бұрын
Thanveer, it's hard to say. There are so many contributing factors.
@rosesbite4 жыл бұрын
this helped me so much with pick a dogbone mount insert my MK6 VW! Thank You!!
@GallagherCorporation4 жыл бұрын
Glad it helped!
@polyurethanemachinery4 жыл бұрын
Thanks for the vedio
@GallagherCorporation4 жыл бұрын
Welcome!
@ThePartyzanin4 жыл бұрын
Great video!
@GallagherCorporation4 жыл бұрын
Glad you enjoyed it
@user-or9gn2gv8w4 жыл бұрын
in that kind of wheel how much is A ? ( hardness of polyurethane )
@GallagherCorporation4 жыл бұрын
Find out more about the hardness of polyurethane here - gallaghercorp.com/polyurethane-durometer-hardness/
@griffinb20094 жыл бұрын
Great video
@Tracks7774 жыл бұрын
nice video
@gizembeliktay46574 жыл бұрын
Hi, first of all, thank you for the informative video. I know that polyurethane is a mixture of isocyanate and polyol components and these parts react with each other by the time they become together. How in the spray coating of polyurethane the parts are mixed and how they become stable when they mixed? I would be grateful if you answer.
@GallagherCorporation4 жыл бұрын
Thanks for watching, Gizem! We are not familiar enough with spray polyurethane to comment on that. We cast mold, injection mold, and 3D print polyurethane.
@marwanhassn4 жыл бұрын
Very nice brother, I work in the same field
@marwanhassn4 жыл бұрын
Nice
@nagaraja.t.s.70695 жыл бұрын
Which is the bonding primer used? And also for different base metals like iron,steel or aluminium primer is same or different?
@GallagherCorporation5 жыл бұрын
Hi Nagaraja, we use several kinds of bonding agent depending on the application. It is possible to use the same bonding agent on a variety of metals.
@musmantaiq6711 Жыл бұрын
@@GallagherCorporation Which bond are you use tpu to aluminium bonding
@diananggitasari98885 жыл бұрын
Hi, can you tell me what machine you used to test the bonding on that video?
Пікірлер
How much speed should you use to pull?
These guys flew delta way too much. I feel like I'm watching the pre flight boarding video lol. Good video though, I appreciate the info!
Which bond are you use for bonding of tpu to aluminium
We could get into the specifics if we partner on something.
is hand casting / Manual casting good for polyurethane process? or machine casting is better
We would confidently say that using meter-mix machines is the way to go.
Is that Method A or B, which one can i learn?
My offroad tires are 55 to 65
I used polyester powder coating on metal (stainless steel and steel) as a primer before casting 90A shore polyurethane 2 part resin. It works great. Again, I used just regular white polyester powder coating baked with high temperature. The bond is so strong that It is very hard to remove polyurethane from metal surface.
Hi Tigran, which polyester powder coating formulation did you try with success? Was it a TGIC polyester or the non -TGIC (or HAA type, also called Primid type)?
Good
Nice video. Could you tell us what kind of binder (glue) do you use for attaching the sample in the metal frame? Thank you.
The metal frame is held together by the bolts. "The preload is maintained during the shear test by four bolts that were tightened down, finger tight, when the sample was compressed."
If a Polyurethane to steel bond is purely shear loaded (so no peel), should the surface roughness still be Ra250? And how well does the bond perform on a pure shear application? Application is a PU disc with diameter 500 mm and thickness 150 mm bonded to a steel bottom and top plate under shear load.
Bonding to two surfaces at the same time can be tricky. Reach out to us if you are experiencing failures and we can talk more.
Have you published any technical papers for this method
Hi Ganesan, just this video. Thanks for watching.
@@GallagherCorporation Thank you for your kind information
What is your bond strength value as N/mm for your polyurethane wheels, i didn't see any information about that in your official site
Ultimately, the bond strength of our products exceeds the materials strength. The values obtained from bond testing are influenced heavily by the urethane compound. Due to this, two parts cast with different materials can both have exceptional bond, but very different values from our bond test.
@@GallagherCorporation I see, can i ask a question too, according to which standard are you testing the bond strength ?
Wish there was more info videos on this before I spend $20
Try checking out the channel from FinMan Fishing Innovations - kzread.info/dron/pUNFKoHzNcOiECLjkgn1sg.html
I know I first saw this like 5 months ago on a targeted ad on IG, and I just went on YT expecting to see a ton of reviews by people who bought it, and the only thing I could see was paid advertisement. Which isn’t a bad thing, I’ll probably still buy it with fishing about to open up in the North East, but was hoping to see it in action on some rods that it wasn’t paid to out there. Even crappy products have reviews saying stay away but I can’t find it anywhere 😊
On Instagram, go to FinmanFishing, lots of content there
Can we use polyurethane for sealing holes in water galvanized steel tanks?
Hello Adeeb, we mold solid polyurethane elastomers. You should reach out to someone that works in sealants. Thank you.
i need an article that speaks about shore A95 TPU under long term compression. can any one help?
Hi @waelomer1990, what do you need to know?
@@GallagherCorporation I need to determine the behaviour of polyurethane A95 under long term compression for a product I am working on Thank you
There’s more to it than just durometer. The geometry will play a major role. Head over to our website and contact us there so you can discuss this in more detail with one of our representatives. gallaghercorp.com/contact/ Thank you!
thanks for breaking down PU hardness into easy to understand examples!
Excellent video! Couple of questions, 1. Does this follow ASTM 4014? was the bonding a cold bonding process? 2. Is the formula for shear modulus 2(F2-F1) /A the same as what was used?
You mentioned tailored made customized to fit. Do you actually do that or use off the shelf products?
Hi Rich! Here's the quote - "When we manufacture products for our customers, we tailor our polyurethane’s properties to fit their needs." Yes, we formulate and process the polyurethane chemistry to provide performance parameters that best meet your requirements.
Very informative, well produced and comprehensive. 👏👍💥
Thanks! Glad you enjoyed it.
4:30 best wedding ring ever seen
You guys should stop making polyurethane and start making educational material. This is one of the best videos I've ever watched, congratulations!
Thanks for your comment, Vinicius.
very nice video. Thanks. what are the standard compression set values for EPDM/Silicone/NBR/FKM/CR /NR rubber?
Thanks for watching! Don't know about those other materials, we're the polyurethane experts!
I didn't know there was so much theory to my everyday work EZ. Great tutorial 👍
Great explanation! Might’ve added the equation for calculating
What is only set
Super helpful and really well produced vid. Thanks!
Glad you enjoyed it!
excellent. thank you for the great video. do you have shear test for anisotropic composite to find G12, G23, G13?
Thanks for watching! And no, we do not.
Thank you for the video : )
You're welcome!
Does tear strength also equate to abrasion resistance?
Good question. Tear strength is a good INDICATOR of abrasion resistance, but it’s not the whole answer. Other material properties, like rebound, can also play a role. Check out our page on abrasion resistance for more details: gallaghercorp.com/polyurethane-abrasion-resistance/ We find that every abrasion situation brings its own set of unique challenges, so please contact us to discuss your specific application with our engineering team.
Hello friends, I am working in a grinding wheels production company and we produce various types of grinding wheels. We also produce Resin bonded wheels in which we experience a problem of abrasive resin layer getting slipped of from the metal base(aluminium). Normally for good adhesion of the abrasive layer, we used to create seration on the aluminium body, grit blast it, also we used to apply a layer of primer on the grit blasted area. But still after all the processes are done our abrasive wheel gets slipped of from the metal base. Can you guys suggest me any good idea how to overcome this issue.
Thanveer, it's hard to say. There are so many contributing factors.
this helped me so much with pick a dogbone mount insert my MK6 VW! Thank You!!
Glad it helped!
Thanks for the vedio
Welcome!
Great video!
Glad you enjoyed it
in that kind of wheel how much is A ? ( hardness of polyurethane )
Find out more about the hardness of polyurethane here - gallaghercorp.com/polyurethane-durometer-hardness/
Great video
nice video
Hi, first of all, thank you for the informative video. I know that polyurethane is a mixture of isocyanate and polyol components and these parts react with each other by the time they become together. How in the spray coating of polyurethane the parts are mixed and how they become stable when they mixed? I would be grateful if you answer.
Thanks for watching, Gizem! We are not familiar enough with spray polyurethane to comment on that. We cast mold, injection mold, and 3D print polyurethane.
Very nice brother, I work in the same field
Nice
Which is the bonding primer used? And also for different base metals like iron,steel or aluminium primer is same or different?
Hi Nagaraja, we use several kinds of bonding agent depending on the application. It is possible to use the same bonding agent on a variety of metals.
@@GallagherCorporation Which bond are you use tpu to aluminium bonding
Hi, can you tell me what machine you used to test the bonding on that video?
Instron Machine
Very informative and compelling. Thank you!