Пікірлер

• 
  @hubertparks-bx9gj3 күн бұрын

  Love itt

• 
  @Coy.ote52 күн бұрын

  I appreciate it

• 
  @TOPDAWGPRODUCTIONS_197 күн бұрын

  Nice mustang how much hp we talkin

• 
  @Coy.ote56 күн бұрын

  @@TOPDAWGPRODUCTIONS_19 I appreciate it makes 470hp/401trq

• 
  @TOPDAWGPRODUCTIONS_196 күн бұрын

  @@Coy.ote5 oh nice

• 
  @Coy.ote56 күн бұрын

  @@TOPDAWGPRODUCTIONS_19 it’s fun to drive runs a 11.4 in the 1/4 mile trying to get it in the 10.98 range before make changes and it’s manual 6spd

• 
  @TD_GRANT6 күн бұрын

  @@Coy.ote5 interesting

• 
  @yallwatchthis7 күн бұрын

  Yours is cleaner! What size rear tire are you running?

• 
  @Coy.ote57 күн бұрын

  @@yallwatchthis hossier 28/11.50r17

• 
  @FANOFTGYT8 күн бұрын

  Clean

• 
  @Coy.ote58 күн бұрын

  @@FANOFTGYT I appreciate it 🫡

• 
  @Patron_FF27418 күн бұрын

  Cool car btw ❤❤

• 
  @Coy.ote58 күн бұрын

  @@Patron_FF2741 🫡 I appreciate the love

• 
  @FijiV89 күн бұрын

  🔥

• 
  @Coy.ote59 күн бұрын

  @@FijiV8 I appreciate it

• 
  @RKSAINT10 күн бұрын

  I’m currently doing this right now with my x3. Did you have to remove the lower coolant line as well, the one right below the one you replaced on the turbo. On my 2019 x3 the lower coolant line is sitting on top of the coolant return line (the one you replaced). I can’t seem to get it out of the turbo I’ve been pulling and wiggleing it but it’s stuc. I’m using PB blaster silicone lube. Any tips or trick to get that line out of the turbo? Thanks

• 
  @Coy.ote510 күн бұрын

  @@RKSAINT no only advise is to pull wiggle and when installing the new line lube the o-ring makes it easier

• 
  @RKSAINT10 күн бұрын

  @@Coy.ote5 got her done just now. Yeah I had to remove the heat shield but I pulled with one hand and wiggled with the other. Came out really easy. My car also only has 60k miles but all my coolant drained out which I didn’t realized because I was so excited I got the hose out.

• 
  @Coy.ote510 күн бұрын

  @@RKSAINT just top off the coolant and bleed the coolant system

• 
  @RKSAINT10 күн бұрын

  @@Coy.ote5 do I have to put it into bleed mode or can I just turn the car on and add coolant as it makes its way with the big coolant tank open? Some say I need to hook up on a charger and put it in bleed mode manually

• 
  @Coy.ote510 күн бұрын

  @@RKSAINT just top it off let the car run turn the heat on and just watch temp hand after few minutes the electric water will cycle coolant back into the reservoir once vehicle is at operating temperature put cap on perform a drive cycle and monitor the temperature while drive

• 
  @user-dr7xf9tj2q12 күн бұрын

  This happened I put led aftermarket lights one side worked for min then both went out , so it’s the ballast fornsure

• 
  @Coy.ote512 күн бұрын

  @@user-dr7xf9tj2q sometimes it can be quality of the bulb, you have to make sure when installing them not to get any oily or any residue form touching the bulb you get on eBay and order the hid ballast some come with the hid bulbs

• 
  @pasqualinoversace388613 күн бұрын

  Thank you

• 
  @Coy.ote513 күн бұрын

  Your welcome I’m glad I could help

• 
  @TheBaptistJimBeam15 күн бұрын

  How did you intall the rubber end of line into block? I replaced o-rings on turbo side..then the rubber hose started leaking. Above the metal part of rear line. Couldnt even see where its routed...Everyone says turbo has to come out to access...coolant lines.

• 
  @Coy.ote515 күн бұрын

  @@TheBaptistJimBeam I lube the o-rings little bit of oil makes it easier to install

• 
  @Coy.ote514 күн бұрын

  It turbo have to come out, anytime you dealing any type o-rings apply some type lubricant it helps installation process smoother

• 
  @rafalemus721817 күн бұрын

  What kit did you use to press then out?

• 
  @Coy.ote517 күн бұрын

  I have snap on master bushing set but you can get something similar from autozone or orilleys Amazon they be a lot cheaper I use my daily in the shop

• 
  @rafalemus721817 күн бұрын

  @@Coy.ote5 I rented a powerbuilt 23 pc ball joint set from advanced auto parts but not sure if this will work

• 
  @Coy.ote517 күн бұрын

  @@rafalemus7218 it should work just have use right cups and insert to press out the bushing then vice versa to install if that make sense. Make sure you use DW-40 on the threads on the tool and a good impact

• 
  @rafalemus721817 күн бұрын

  @@Coy.ote5 thanks I'll give it a try tomorrow

• 
  @Coy.ote517 күн бұрын

  Your welcome if you have more questions or need any help or guidance lmk

• 
  @CARLAUVER18 күн бұрын

  Bro!? Whatup with the steering though?

• 
  @Coy.ote517 күн бұрын

  Nothing it’s just slightly turn in that video

• 
  @tyrizzletrains761619 күн бұрын

  Did you have somebody evacuate the coolant?

• 
  @Coy.ote519 күн бұрын

  I didn’t have any Freon in the a/c system due to a leak in the condenser

• 
  @fred_b_36022 күн бұрын

  You 100% right my brudda. Keep going!

• 
  @Coy.ote522 күн бұрын

  I appreciate it 💯

• 
  @jmkarting723322 күн бұрын

  Yessir

• 
  @Coy.ote514 күн бұрын

  I appreciate it

• 
  @jmkarting723322 күн бұрын

  Oh yeah

• 
  @jmkarting723322 күн бұрын

  Dang

• 
  @Coy.ote520 күн бұрын

  It’s great place to travel

• 
  @jmkarting723322 күн бұрын

  Yup I'm a Jr drag racer I'm in a used car so it took a while to fix up because there was a lot to fix if you ever see a car that is purple has JM racing on it and says Levi Johnson that's me👍

• 
  @Coy.ote522 күн бұрын

  Where you race at at

• 
  @jmkarting723322 күн бұрын

  HELL YEAH

• 
  @Coy.ote515 күн бұрын

  Next event in August

• 
  @jmkarting723322 күн бұрын

  Drag car????

• 
  @Coy.ote522 күн бұрын

  I daily drive it’s not no race car or anything it’s still street legal but it’s something to have fun in, I Mainly race at the track

• 
  @jakewalsh161018 күн бұрын

  Yes bro!!!!!!

• 
  @Tam_Tam_5.0Ай бұрын

  I had this same problem when I went FBO . Eventually I had the battery replaced along with spark plugs and injectors. I have an EVAP leak that I’m still trying to locate unfortunately.

• 
  @Coy.ote5Ай бұрын

  I just upgraded to pmas Hpx-F2 map sensor and new revision from Lund and it’s running ok I’m take car to the track this Sunday

• 
  @tonymontana7318Ай бұрын

  Is ther a way to put 55 watt ballast for that same car

• 
  @Coy.ote5Ай бұрын

  Yes they make plug in play kits you can install

• 
  @AlexanderCastillo-of1fpАй бұрын

  Took my coil out and the boots were wrapped in electrical tape to cover the boots splitting but it lasted since 2018 so I guess it worked

• 
  @Coy.ote5Ай бұрын

  That’s crazy I never seen that before

• 
  @MarcoPerez-cz5dvАй бұрын

  Full vid??

• 
  @Coy.ote5Ай бұрын

  Unfortunately I don’t

• 
  @888King_SagАй бұрын

  Hit play, wait 7-8 seconds - you welcome

• 
  @Coy.ote5Ай бұрын

  Thank you

• 
  @mikkec762 ай бұрын

  Are you able to get ro the 2 cat bolts from the top or do you still have to go underneath?

• 
  @Coy.ote52 ай бұрын

  Yes depending on the tools you have its best to go threw the bottom

• 
  @J.Cannon4202 ай бұрын

  Thank you so much for this video! I just finished replacing the exhaust manifold on my 2012 accent. Took me 3-4 hours working at my own pace and your idea to take off the motor mount to make space was crucial to it going so well. Anyways, If someone finds this video because you're considering fixing your own dirty cat, this method of dropping the motor temporarily worked for me. Job wasn't exactly easy, but had no major hassles. Cheers!

• 
  @Coy.ote52 ай бұрын

  I really appreciate it and im glad and happy that this video help you, plz continue to support and watch the channel. Thank you 🙏

• 
  @xXMr.WiGGleZzXx2 ай бұрын

  Ok everyone. Both of these bushings are exact the same. He just messed up and bought two sets. No the other set does not fit anyone else. That’s why he didn’t show himself installing them.

• 
  @Coy.ote52 ай бұрын

  Guys he’s correct they’re the same size but to different styles bushing. I installed BK055 bmr ones with snap ring and ended not using the BK081 Bmr bushing. I didnt mess up ordering same bushings I installed in another set controls arms had laying and sold to someone.

• 
  @marcolemus25742 ай бұрын

  How did u lift the engine ?

• 
  @Coy.ote52 ай бұрын

  Take a wood block and place on your floor jack that way you don’t dent the oil pan when lifting up the engine

• 
  @Coy.ote52 ай бұрын

  sub to channel

• 
  @victorcruz42242 ай бұрын

  When’s the meet and greet

• 
  @Coy.ote52 ай бұрын

  You tell me lol

• 
  @zachmendelson_2 ай бұрын

  Drop the full mod list

• 
  @Coy.ote52 ай бұрын

  Bet sub to the channel

• 
  @Coy.ote52 ай бұрын

  I’m drop mod list in video today be in look out for it

• 
  @morganrosalyn2 ай бұрын

  GOOD JOB!! question...I have a 2017, do I 2 or 1 Cat converters, a front and back

• 
  @Coy.ote52 ай бұрын

  It’s has two, one is together with the manifold and the other is on the exhaust pipe

• 
  @morganrosalyn2 ай бұрын

  @@Coy.ote5 ok...Thank u.

• 
  @Coy.ote52 ай бұрын

  @@morganrosalyn you welcome forget to like and subscribe I appreciate all the support

• 
  @tytalks57693 ай бұрын

  Have to replace mine this week…Did you do a coolant flush or bleed after ?

• 
  @Coy.ote53 ай бұрын

  You bleed it after it’s done

• 
  @tytalks57693 ай бұрын

  @@Coy.ote5 would you happen to have a link to a video on how to do that I can’t find one I have a 2018 430i.

• 
  @Coy.ote53 ай бұрын

  @@tytalks5769 I give one sec

• 
  @Coy.ote53 ай бұрын

  @@tytalks5769 yes upload this video link in short video you watch it’s not a step by step but it should help you

• 
  @graham40563 ай бұрын

  "promo sm" 🏃

• 
  @m0jayd373 ай бұрын

  thank you , just wondering if you can then access the trunk from behind there

• 
  @Coy.ote53 ай бұрын

  Yes you can

• 
  @schmick634 ай бұрын

  I have a 2017 Velar with this 3.0 engine. The Y pipe under the supercharger was done under warranty (cracked within first 2 years), then the thermostat housing started to leak so I installed a new one, and now the water pump is leaking. . . POS

• 
  @Coy.ote54 ай бұрын

  Sorry you going through that I hope you get it taken care of

• 
  @michaeldeleon59604 ай бұрын

  Bad ass bro sounds good has me sold

• 
  @Coy.ote54 ай бұрын

  I appreciate it, like said if have more questions let me know I have done all the work you see in my videos myself

• 
  @michaeldeleon59604 ай бұрын

  Is it loud loud or nah

• 
  @Coy.ote54 ай бұрын

  Yes it 1 7/8 headers catalyst 3in to 3in fab work by me 3in h-pipe with dumps, it’s loud

• 
  @Coy.ote54 ай бұрын

  Sub to channel

• 
  @Coy.ote54 ай бұрын

  kzread.infoCkiLitJG3PA?si=pN283ljoTKRgVHS8

• 
  @davidb.44124 ай бұрын

  Nice brother. Love the edits.

• 
  @Coy.ote54 ай бұрын

  I appreciate it

• 
  @davidb.44124 ай бұрын

  I support you brother and your progress.

• 
  @michaeldeleon59604 ай бұрын

  Which bullet mufflers u using?

• 
  @Coy.ote54 ай бұрын

  Dyno max race series 3in summit sell them

• 
  @michaeldeleon59604 ай бұрын

  ​@@Coy.ote5u have pics of how the dumps are setup?

• 
  @Coy.ote54 ай бұрын

  I don’t have any photos one videos at end of the video I’m talking about one the exhaust hangers broke

• 
  @Coy.ote54 ай бұрын

  kzread.info/dash/bejne/d2xtyJqrks28pLg.htmlsi=hz4hrGa95LWYIdAc

• 
  @juanbarbosa34814 ай бұрын

  I have a hyundai accent 2016, is it located in the same place?

• 
  @Coy.ote54 ай бұрын

  Yes sir

• 
  @emmanuelpeniche65284 ай бұрын

  How did you get the tire to free spin like that? Does is have to be on neutral?

• 
  @Coy.ote54 ай бұрын

  Vehicle is front wheel drive it doesn’t have rear axle in the back

• 
  @xXMr.WiGGleZzXx4 ай бұрын

  I’m about to do this. But one question, so the other set, the billet ones, aren’t they the same ones? Or are those for the spot next to the ones you replaced?

• 
  @Coy.ote54 ай бұрын

  Yes just cost more they other one and will only fit the forward control arm bushing

• 
  @ICarrillo-lo8cf5 ай бұрын

  0:17 beauriful

• 
  @Coy.ote55 ай бұрын

  Thank you I appreciate it

• 
  @ICarrillo-lo8cf5 ай бұрын

  @@Coy.ote5🙏🫶

• 
  @Coy.ote55 ай бұрын

  You subscribe to channel yet

• 
  @XFR9375 ай бұрын

  I noticed the coolant on my XFR, leaking in the same place. Had a new waterpump installed two years ago, do you think i should replace that again.

• 
  @Coy.ote55 ай бұрын

  No just replaced that one part and due to heat and cooling down that was causes the problem and it’s plastic so o-rings fail and starts slow leak

• 
  @XFR9375 ай бұрын

  @@Coy.ote5 Thanks mate really appreciate your advice. I had all the supercharger nose cone repaired, just surprised the garage just did not make me aware about this plastic pipe, i would have replaced it.

• 
  @Coy.ote55 ай бұрын

  @@XFR937 a lot time shop unaware of this related issue it’s common issue your welcome I glad I could help subscribe to channel and watch some videos

• 
  @SuspiciousDoor5 ай бұрын

  thank you

• 
  @Coy.ote55 ай бұрын

  Welcome

• 
  @jasonpierson32305 ай бұрын

  Did you just use a floor jack to support the motor and lower it down after removing the motor mounts?

• 
  @Coy.ote55 ай бұрын

  Yes i did

• 
  @user-so5us6mh2q5 ай бұрын

  But... you didn't show how to replace it?

• 
  @Coy.ote55 ай бұрын

  I was in bit of a rush, she needed her vehicle it’s located underneath intake manifold toward the front of the motor it’s only one vvt solenoid

• 
  @RC89235 ай бұрын

  What rims are those the ones with the Annabelle doll

• 
  @Coy.ote55 ай бұрын

  Vertini rfs1.7 20in

• 
  @Thedjcodeman6 ай бұрын

  Just did this last week. Those bushings can be a bitch to press in. Use a lot of silicone grease! Also the width of the toe link fork is slightly smaller so you may need to bend the metal on one side slightly to get the upgraded bushing to fit.

• 
  @Coy.ote56 ай бұрын

  I have couple of controls I’m doing for few buddies, I always put my bearings in my deep freezer makes installing them easier, but nothing easy about it takes a lot of patience

• 
  @Thedjcodeman6 ай бұрын

  @Mustang214 no doubt. I had mine in the freezer as well. Having the right tool for the job made it much easier. Got the loaner tool from autozone and it went ok

• 
  @Coy.ote56 ай бұрын

  @@Thedjcodeman yes sir i also just installed one piece drive shaft on my car sub to channel all sub back

• 
  @Thedjcodeman6 ай бұрын

  @@Coy.ote5 subd

• 
  @Coy.ote56 ай бұрын

  @@Thedjcodeman appreciate I already sub