Пікірлер

• 
  @alfredo84316 ай бұрын

  1:36 😅

• 
  @TheRealBurtL Жыл бұрын

  So the black wire from the power source (3.7V rechargeable battery) goes to the LED meter and the negative Pole of the 1.5 volt battery? It's difficult to see all the wiring you demonstrated with. For this type of work I would use a breadboard, you can tin the end of the wires and they'll slide right in and out of a breadboard. Thanks for helping me learn how these three wire LED voltmeters work. I have 10 four digit, three wire units on the way right now...

• 
  @sdkfz251 Жыл бұрын

  Poor light photography along with badly selected background text colour

• 
  @anyonecanmakeit718 Жыл бұрын

  Yes it works👍🏻

• 
  @gabrielconstantine7384 Жыл бұрын

  Thanks..wasn't sure how to measure below 4.4v. It helped me out.

• 
  @penncapt Жыл бұрын

  I have a 58.8 battery. Can I connect both non black wires to pos and get a good reading? Or does the red wire have to have 3-30?

• 
  @electroideas3255 Жыл бұрын

  The meter can only measure up to 30v, so no you can't, but there are 100v versions of this meter and with that you can. Just make sure that it can be powered with 60v.

• 
  @kmhooibg7577 Жыл бұрын

  Hello, I have a question. Is the first battery 4.14V?

• 
  @kmhooibg7577 Жыл бұрын

  I would like to test an AA battery. Base on the information that you provided, what I understand is connect red wire to the 4.14V battery+ and black wire to the b-. Then connect white wire to AA+ and connect black wire to AA-, is it?

• 
  @electroideas3255 Жыл бұрын

  ​ @KMHooi BG The first battery is 4.2v but slightly discharged.

• 
  @electroideas3255 Жыл бұрын

  Yes that is correct, red wire is supplying power for the meter, white wire measures voltage, black wire is connected to bouth batteries " - " terminal.

• 
  @mylittlebrotherca9691 Жыл бұрын

  Awesome.😎👍

• 
  @serialshitposter186 Жыл бұрын

  Thanks.

• 
  @stclairstclair2 жыл бұрын

  Throw that microphone out and make a good ol fashioned mime video! ugg.

• 
  @jumbo9996142 жыл бұрын

  I'm making voltage divider for powering my bluetooth with 3.3v from arduino's 5v tx pin. How do you use this meter to measure it?

• 
  @electroideas32552 жыл бұрын

  Connect the meter's ground wire to the arduino's ground pin , connect the v.meter's red wire to the arduino,s 5v pin, and connect the white wire to your voltage divider and it should work.

• 
  @jumbo9996142 жыл бұрын

  @@electroideas3255 Thank you

• 
  @mikepercival56233 жыл бұрын

  Yet another five minute advert before I can watch the video - boring!

• 
  @equanimousawareness3 жыл бұрын

  The light blue fonts are difficult to read.

• 
  @electroideas32553 жыл бұрын

  Sorry

• 
  @robertmccully27923 жыл бұрын

  How did you figure all this out. I doubt there was instructions.?? I love You Tube..

• 
  @electroideas32553 жыл бұрын

  Well , i was connecting one of these moduls to some kind of power supply and i used u connect the white and the red wire together , by mistake i only connected the red and the module showed 0.00 V. ( Sorry for not replying quickly )

• 
  @bobslagle65223 жыл бұрын

  HI Tom - Thanks for the video. I have a question. Can I wire a DC analog volt meter that will allow me to go in reverse without the meter going backwards?

• 
  @electroideas32553 жыл бұрын

  I think it's possible , but I dont 'know how . Try searching it on KZread or google .But....i have in idea . If you want to connect the volt meter on a motor or somthing like that , if you connect a full bridge rectifire on it with the ~~side to the motor than connect the red wire to the white wire and than to the + output of the full bridge rectifire and black goes to - after this you shoud read the voltage in + on the volt meter even if the motor is going backwards .

• 
  @bobslagle65223 жыл бұрын

  @@electroideas3255 Thanks for getting back to me. Would you have a schematic for the full bridge rectifier?

• 
  @electroideas32553 жыл бұрын

  @@bobslagle6522 Sure. images.app.goo.gl/nnAmKuy5KEqtDbFS9 : it is made of 4 diodes. If the picture doesn't help , here's a video link : kzread.info/dash/bejne/mYVnvMaunNa8cso.html : you can use whatever diode you have . The capacitor value doesn't matter that much but i recomend : 47-100 μf and about 100 v ones.

• 
  @sogarsolder30313 жыл бұрын

  berikan keterangan yang jelas,..video ngga jelas.......

• 
  @neptunez34953 жыл бұрын

  it was 20 cents a piece, what did you expect?

• 
  @dipeshkaushal2564 жыл бұрын

  6 Tip ka wiring

• 
  @bekesibotond11254 жыл бұрын

  Vigazz nehogy magadra gyusd a hazat..😂

• 
  @borgonosclarences.17814 жыл бұрын

  Mr. What Capacitors you used?

• 
  @electroideas32554 жыл бұрын

  I used electrolytic capacitors , because I don't have other type of capacitors . If you have access to super capacitors with 1to 10 Farad than use them.

• 
  @electroideas32554 жыл бұрын

  With super capacitors(aboute 5-6 Farads) you need to shake aboute 5 to 15 minutes and than it will light up for aboute 8 miutes.

• 
  @borgonosclarences.17814 жыл бұрын

  @@electroideas3255 what value you use?

• 
  @borgonosclarences.17814 жыл бұрын

  @@electroideas3255 and how you solder them?

• 
  @electroideas32554 жыл бұрын

  In paralell. + To + and - to -

• 
  @vektor66014 жыл бұрын

  Nice! 👌

• 
  @zukii40924 жыл бұрын

  elso

• 
  @zalan_is91544 жыл бұрын

  Imadlak😂😂😂🤣

• 
  @electroideas32554 жыл бұрын

  😂😂😂...thx

• 
  @zalan_is91544 жыл бұрын

  😍😍😍😍😍te vagy a legjobb

• 
  @electroideas32554 жыл бұрын

  Ne hazudj

• 
  @zalan_is91544 жыл бұрын

  Buszke vagyok rad

• 
  @electroideas32554 жыл бұрын

  Kösz/thank you

• 
  @zalan_is91544 жыл бұрын

  Honnan vetted

• 
  @electroideas32554 жыл бұрын

  I bought in a supermarket(polus) for 20¢/1lej but you cant use like a power bank because the pcb (az áramkör) is bad in it