Great video. I am the manufacturer of the pump, thank you very much for sharing our products. If you have any aftermarket problems can contact us to use the manual behind the mailbox. We have found a better shock absorber foot can no longer need a mat. If you need to contact us, in order to thank you for sharing our products, we will give you free of charge. Thanks again.

@Wingman115

7 жыл бұрын

+hui jin Thanks for reaching out. I will let folks know.

@sme4969

7 жыл бұрын

why is it not recommended to fill a dive bottle ? it stated in this video it takes 10 mins per 1 litre. i have a 3 litre so that would be 30 mins fill. as long as the unit is kept cool it should be fine ?

@Wingman115

7 жыл бұрын

sme4969 It means it's not meant for breathing like scuba diving.

@joelstoeltzing4979

7 жыл бұрын

I have a question regarding the 220/240v model. It says it operates @ 50hertz. Here in America, we operate @60hertz. Most motor appliances do not care. Just wanting to make sure this compressor would be okay with the slightly different frequency. Thank you for your time.

@sme4969

7 жыл бұрын

Wingman115 yes but some people use dive bottles to fill there guns. so is this kit good enough to fill a dive bottle ? not everyone has a buddy bottle gun. Some people use the bottles to top up when out in the field

Really glad I watched your video because you include some info I did not know. Was not aware they made these units in 220v which is huge for people that have easy access to a 220v outlet. Thank you!!

It was a really good video. I have just received my compressors and have not set it up. Thanks to your video I should have no problems. Thanks! Bob Lachapelle

Very useful demo and explanation. I have just taken delivery of this model pump (240v) and it's true what they say - a picture is worth a thousand words. Glad to view this before I give the pump its first run. Good emphasis on bleeding the air off before switching off. I look forward to viewing your proposed videos on long-term use including pump maintenance. Many thanks.

@Wingman115

7 жыл бұрын

Thanks for watching.

Thanks for this. Answered my questions and concerns. Much appreciated! Keep us posted!

@Wingman115

7 жыл бұрын

Your welcome.

@datnihgahpanda6646

5 жыл бұрын

@@Wingman115 you're*

Well done John! Great video!

Thanks for this video. After much research, I purchased this model as well and wanted to find a KZread showing actual usage but in English. I am new to pcp air rifles and feel much more at ease that I made a wise purchase.

@Wingman115

7 жыл бұрын

Thanks for watching.

Great point about having enough electrical power. If using 117 volts ac, a 15 amp breaker is insufficient based on the power load - be sure to have a 20 amp breaker with no other devices on the line. Also, avoid using a low gauge extension cable that would cause a voltage drop to the compressor - causing overheating. Many thanks for the awesome video!

@billdesmet3929

2 жыл бұрын

Someone is an ELECTRICIAN??? Or dork?

You can’t beat it price wise. The digital thermometer was screwing up on mine and they sent me out another one. No problems. So far so good

Makes sense to me, worth it's weight after you factor in what you mentioned. Cool review!

@Wingman115

7 жыл бұрын

+BlackRifle Survival There is value here if taken care of it should last a long time.

Thank you for the info. Made my mind up on its purchase

Looks like a great lil pump for us PCP guys!

@Wingman115

7 жыл бұрын

Reality Survival It's working out good with my Escape.

@IntelCoreI77700K

6 жыл бұрын

heh. lil Pump

Thanks for the informative video!

Great little pump. Thanks for making the effort to post this. I ended up buying a 'clone' version that has a brand name of "Aceeagle". I think the components are pretty similar based on one of the tear down vids I saw of this Yong Heng... but I probably should have got the Yong Heng in the end as in hindsight I don't see too many vids about the Aceeagle. My Aceeagle seemed to do the job but I think it's taking a bit longer than it should. It topped up my 4.5l tank from 160bar to a hair under 280bar in about 45 minutes. Still WAY less time than it takes to go to the stupid dive shop and get ripped for £35 to get it filled :) I used a very big bucket with the garden hose overflowing it and my temps stayed at around 45deg. I ordered another inline filter for mine with loads more filter elements..so I will have a second stage filter. It would be great if there was some way to test the purity (dryness and no oil) in the air produced.... You are spot on about maintenance of these ...but I think the spares for these will be cheap as chips. Given that the con rod is aluminium and has no bearing on the crankshaft I think that could be point of failure but I will keep an eye on it. Also...as the piston starts to wear out, I think the air will start getting contaminated more but hey...you cannot beat the price of these things. Hats off to the inventor of these things!

Fantastic video John, great speaker

@Wingman115

6 жыл бұрын

+Omar Hammoud 👊🏻👍🏻

Thanks for the informative video - just bought one!

@Wingman115

4 жыл бұрын

👍🏻👊🏻

Thanks for the review.

good job man I need this video

I've had this air compressor for 18 mouths now. Not had one problem with this product one's. And still runs as good as the day I got it.

@Wingman115

7 жыл бұрын

Good stuff.

That is nice I didn't know they made anything that small. Thanks for sharing. God bless and stay safe.

@Wingman115

7 жыл бұрын

+Rich Schwartz Its amazing that a compressor that small can achieve that high of a psi. Thanks for watching.

Great informative video nice to know that one of these Chinese compressors is actually worth the money can't wait for your video on how this compressor is holding up so far so good thanks again for the info

@Wingman115

7 жыл бұрын

Compressor is running fine. I've done about 20 fills with it and no issue's so far.

great vid! Thanks

I do love mine!!! Just wish there was more information on them!

good rundown!

@Wingman115

7 жыл бұрын

+Jim Cyr Thanks Jim.

Nice 👍🏼😎 Thanks 🙏🏼🤩🤗

if also let it run a bit after finished with bleeds undone to try it cool with water circulating through it

thanks so much for adding the link

@Wingman115

7 жыл бұрын

Your welcome.

I keep the bleed off valves open before turning on the machine too. It allows the unit to properly lube up before under load.

@Wingman115

Жыл бұрын

👍🏻👊🏻

The one i ordered a few days a go, is 110v and has outo shut off. With a pressure shut down setting on the gauge. It will arrive to me this friday

I don't know if anyone mentioned it, but if you keep pressure in the auxiliary tank, say more than 500 lbs, it will help to keep condensation off of the tank.

very helpful, thanks

@Wingman115

6 жыл бұрын

Thanks for watching.

Hi great review looks like it's the dogs dangaly bits. I'm thinking of getting one and was wondering if you have done a long term review if not how is holding up.found the UK link very helpful

thank you wingman what do you thing how the Yong being would compare to the shoebox as far as filling time on a 45/90 carbon fiber?

Open the moisture and pressure valve before switching on. Then close them after switching on after 30 secs. This gives time for any moisture to be expelled. Open and close the valves in 2 to 3 min intervals to keep expelling the moisture if you do not have a the extra filter system (charcoal, clay/ beads etc... and cotton filters). Someone explained this in another vid hope it helps.

Great video. I've been looking at high pressure compressors for a while now. I'm interested in how long this one lasts. I hope you keep very accurate records as far as how long each fill time is, and start and finish air pressures so we can see what kind of loss or wear we can expect over time and use. I'd also take that new spare O-ring kit to the local parts store and match up spares now, so you know what you need, unless they included part numbers, which I doubt they did since this is made outside the USA. Keep up the great work.

@Wingman115

7 жыл бұрын

wjf213 I will be keeping a journal.

@randomvideosfilmcollection3161

7 жыл бұрын

wjf213 sound advice however they will offer you to buy spares from them and thats ok cause they are offering us a product at a great price that the U.S. makers take advantage of us on. like shoebox and air vent. So im ok with the China men trying to sell me spare oRings... BUT SOUND ADVICE. match spares up at hardware store and online to see if you can get a easy source for spares. Id advise using really top shelf oil also. no cheap crude for the babygirl. Also its worth to mention that using bottled distilled water could help add longer life to our new sweetheart instead of using hard ol tap water. 99cents a gallon is worth the extra life in my book. Pamper your best girls and they will do you good for alot longer than if you just treat them like common dolls

@randomvideosfilmcollection3161

7 жыл бұрын

Wingman115 good video @ wing man.. [[[PLEASE DO A indepth detailed Video on the Rebuild when the time comes "hopefully a long while from now" but it will come -which is normal wear for hpa comps- So please just remember us then to take the time to document the rebuild...Thanks Sooo Much...Good Day Sir'

@kevinalt1707

7 жыл бұрын

DrJones are u being serious u fucktard

@billdesmet3929

2 жыл бұрын

He never followed up with us; probably in prison...

sorry if this was asked be for. But, dose the 220, work faster, or run hotter, then the 110. what are the main differences between the 2? thanks

would you reccomend this? what safety precautions are in place.. I see a blow off valve on there is there any other safety aspects?

I am looking into getting one of these... I am a little confused on the 30 mpa vs 40 mpa. And 300 bar vs 400 bar. I use 4500 psi tanks for airsoft but I don't know much about this stuff and what do be looking for. Any help?

One other detail on the cooling water tubing. The discharge/return to bucket hose gets so warm that the tubing can collapse. I bought a short piece of reinforced tubing and it does not distort with hot water going through it. I also secure this hose above the water line in the bucket so I can be certain that the cooling water flow is not disrupted.

Hello I just got one of these yh where do you get extra burst disk yes I blew one on first fill of a 90 ci /4500 thanks

Yes I did get it eventually.. took a long time.. this works great..

@Wingman115

6 жыл бұрын

Thanks for the comment and watching.

Awesome thing to review. I have paintball guns and airguns and while I like using CO2 cartridges, as you know they can't provide enough gas for the higher power and faster shooting airguns or paintguns.... not enough volume and not enough shots for extended shooting and they use HPA anyway. I've been curious, but they are often pricey from paintball dealers.

What kind of connection come with compressor ? Will I need adapter to fill an Omega tank that has a dinn300 valve and a foster#12 fill connector on hose?

The compressors are set for 30mpa (300barg) , I normally top up bottles to 300barg, but the overpressure bursting disc goes at this pressure, I see a few eBay details state it can be made to run slightly higher, any ideas on how to achieve this I only need 310/320 barg.

You need to connect the probe from the thermometer to the small hole in the back of the cylinder head. This will then give you a more accurate reading of the pump temperature. Don't let it get over 65 deg C.

@billdesmet3929

2 жыл бұрын

Yes, I seen 2 videos where both Dorks don't know that... GREAT POINT

I have received mine today and the female quick disconnect didn't work on my tank so I remove one from my air hose to to check the unit so far so good now have to invest an other $19 for quick disconnect plus $8 shipping. not complaining about it just letting airguner to be aware. once again thank you for the review.

@Wingman115

7 жыл бұрын

Weird mine worked fine.

@ibson0787

7 жыл бұрын

Wingman115 maybe because I have a different tank mine is the airtanksforsale.

Washer, dryer, and fridge are usually 220v output

The light turns on but nothing happens after I flip the switch do I need to wait or is their something that I am not doing correctly?

Just got my Yong Heng from Walmart. It arrived 6 days earlier than they said it would. The manual is almost worthless. It says to use a gasket where the air filler hose connects to the pump. Does it mean the metal ring/washer with a rubber insert? When I used that, the fitting got tight before that gasket made contact. It came with 2 of them - am I supposed to use 2? I have seen where some Yong Heng units use a white gasket, but mine didn't come with those.

Wingman 115 Liked your review of the PCP compressor. Was wondering how the compressor is working out for you? I have noticed the price of the unit is coming down. I have seen the unit as low as $245 was thinking about getting one. Any thoughts?

@Wingman115

6 жыл бұрын

Still going strong. Thanks for watching.

If I’m wanting to use this air compressor to fill a scba what would I need on my scba to hook up quick connect I have a standard Scott scba for firefighting valve where do I buy adapter to hook up to the hose from air pump?

Does it filter out any moisture from going into the tank? Does it come with the connector to connect to hpa tank?

Very Nice video. I have been a little hesitate to purchase on of these but you did a good job explaining this unit. Do you have an opinion on how this compares to the AirVenturi Compressor that sells for $1200-$1300? I'm leaning toward the Yong Heng but not sure on the longevity on this unit. I guess we will have to wait a few months to hear back from you. Thank you!

@Wingman115

6 жыл бұрын

I've seen the AirVenturi at Shot Show but I haven't had a chance to use one..

I am getting air pressure blowing from the black plastic part that sits in the oil filler space is that crackcase pressure and is the engine fooked?

Can you not add a pressure regulator either on the pump or tank to control your pressure either out or in?

Is there a way to put a moisture trap on the air input side of pump.Here in the humid south moisture is an issue.

Hey whats up? Question its been 1 year how is the Yong Heng Air Compressor holding up??? Thank you for your time.

I just tested my Yong Heng air pump, and it draws more than 17 amps while running and over 22 amps when starting! They must have left off a "1" in the manual because it's rated at 1800W, so there's no way it only draws 8 amps. I decided to test it because it kept blowing the breaker on my power strip.

Question, the bleed on the side with the gauge, on the bottom of the block there is the hole for bleeding, but when I have it tight I am getting leaking from it. Do you happen to know why and how I can fix it?

When will you be doing the follow-up video?

These Chinese HPA compressors are going to allow a lot more airgunners to enjoy the shooting without all the pumping. My version is 220volts 50 hz. I cut the end off the cord and wired it into a fused disconnect switch with 10 amp fuses. I added a cord to fit my clothes dryer outlet and good to go. Remember this is 240 volt 60 hz on USA power. This means more power 240 volts vs. 220 volts but higher speed on the electric motor at 60 cycles vs. 50 cycles. Be sure to use frozen ice in milk jugs to keep the 5 gallon bucket cool and you can fill a 60 minute SCBA tank in one hour with no overheat issues. Great review Wingman. BTW a similar compressor is on Ebay now for $343. and free shipping. My opinion is that this compressor will pay for itself very quickly but the time it takes to set it up it goes much better filling a large tank that will last a while.

@Wingman115

7 жыл бұрын

+Chaz Jeepster Your right they are a huge game changer for pcp shooters.

It did not find the follow-up video. Is this compressor still running?

You said you would do a follow up video on this, I tried to look for it and didn't see anything in a title about it. Can you direct me to the video where you did the update? I would like to buy one for myself but I want to see how this one fares. Thanks.

@halomaniac74

3 жыл бұрын

Guess it wasn't a good one.

What brand/sIze carbon fiber tank is it? How many top-offs from 2000 psi do you get from the carbon fiber tank? Approx. how many shots till carbon fiber tanks drops to 2000 psi?

I know this is an old video but thought I would add some info. Any of these lighter duty HPA compressors should be switched on with the high pressure bleed valve open unless starting to fill gun or tank from completely empty or close to it and then once running close the high pressure bleed valve and start filling. Nearly everyone I know now filling bottles are using a one way flow valve like in our PCP guns so you can refill a bottle from 2K to 3K and start up with the high pressure bleed valve open. Alot of airgunners I know with these lighter duty compressors with the automatic shut off has had problems with the setting gauge, relay or the electric motor, also when the compressor is just switched off at 3000psi to 4500psi abruptly the stop can be violent compared to a no pressure shut off. No load starts & stops will increase the life of these lighter duty HPA compressors by being much easier on the relay & electric motor that drives the compressor as well as the pump piston and crank when you eliminate abrupt stops & starts under high pressure.

Could I substitute a gallon or two of Antifreeze so eliminate water deposits build up inside the pump?

@Wingman115

6 жыл бұрын

Not sure on that one.

I'm interested in your follow up video. Thinking about getting one of these.

@Wingman115

6 жыл бұрын

+P. T. Anderson Still going strong.

Good review! I'd be interested in a follow-up video about adding an inline water/oil trap. I'm a paintballer and use these tanks all the time. One thing you simply cannot have is any oil going into the tanks. I used to work at a proshop and draining the compressor there every night would get almost a gallon of water and oil each time. So it makes me a bit twitchy that this kind of compressor has no trap. Also, do you air rifle guys use tank covers of any kind? The bottles are epoxy coated to keep the fibers safe but it's always recommended to get a bottle cover to help in case of drops. If the tank gets damage to the epoxy that goes into the fibers, that is, if any of the fibers are damaged at >all Enjoyed the video! Will look forward to a follow up.

great, what kind of oil do you use? thanks

I just received my yh yesterday blew the burst disk on first fill after break-in where can I purchase more disk should have extra but didn't thanks

its been a year since you uploaded this video... just wondering how is the pump doing any updates?

@joelthomas79

3 жыл бұрын

I’ve had mine for a year. No problems so far. Keep it cold while using, I use 5 gallon bucket w ice. Keeps it less than 50 degrees Celsius.

Does the female Foster fitting, on the end of the output hose, come with the pump or did you add that? I ordered one of these pumps last night.

@Wingman115

7 жыл бұрын

+Jack Leach It all comes with the unit.

I'm in the process of ordering one of their new 110V with the set pressure shut off feature! Keep us updated on the durability of the unit.

@Wingman115

6 жыл бұрын

Will do.

Wingman115 thanks for your efforts and a great review... Please guide me that what's the difference between autoshutoff and set pressure plate version.. Which one is better in your opinion

@Wingman115

5 жыл бұрын

Well I don't have the auto shutoff so I can't speak to that. All I know is if you keep this compressor cool it will run just fine for the money.

This all sounds really cool, only a few weeks ago watching your show I found out about Air Force Air Guns👍🏽 Is there an air gun season in California? I live in Santa Clarita at the edge of Angeles forest. What do you hunt with the air gun ? We live in the same type of climate . Thanks GW

@Wingman115

6 жыл бұрын

I saw the E-Pump at Shot Show. I'm impressed with what it can do.

@eaglebeak1924

6 жыл бұрын

Airgun season is between duck season and wabbit season.

Do you have any issues with dirty air coming out of the output valve? I'm concerned about dirty, oily air getting into my tanks.

@Wingman115

6 жыл бұрын

+Psquiddy01 No so far so good. I check it on each fill.

I've been following your channel for a long time, how has this compressor held up? I'm looking at getting one but still unsure about this one.

@unknownone8479

6 жыл бұрын

Trotliners following

@Wingman115

6 жыл бұрын

Running good. Just keep it cool and it will work fine.

@unknownone8479

6 жыл бұрын

Wingman115 so your rifle as no sign of water damage

I just order one from Walmart.com price with free shipping to me for 329.00 . It looks like a very good made and a kick ass price . Very nice video thank you again you made it very easy to decide on buying one . Save a lot of money too .

If I were to need to fill several tanks, one after each other, would you recommend running really cold water, like ice water? Another idea i had was instead of running a recirculating water system, I would make an adaptor for my hose so it would use my house water pressure to constantly pump fresh, cold water through the system until i was finished filling my tanks. I have two tanks around 45-50 CI and 3 smaller tanks that fit in the stock of my air rifle that is around 20-25 CI. The larger tanks go in my backpack and has a remote line that can go to any of my airsoft rifles. Thanks for the info in the video. Been thinking of getting one and now I am definitely more interested. It will definitely beat using a hand pump! It would be nice to set it up and record the fill times for all of my tanks so I can hook it up and start a timer, then can do other things while my tank is filling. One thing I might do it build a daisy chain adapter that will allow me to hook up all of my tanks, or at least 3 or 4 at once, then it will fill all of the tanks at the same time. Then you just close the valves ill install on the daisy chain, release the pressure in the line and disconnect the tanks from the system.

@Wingman115

3 жыл бұрын

I would put ice in the water.

Hey whats up Jon? I have a question, How is the compressor holding up? I am new to air gunning and thinking about getting me one would it be worth it? I have limited budget. Thank you for your time.

@Wingman115

7 жыл бұрын

Compressor is holding up well. Just take care of it and it will work fine. I filled a friends 45 minute bottle last week. It took about a hour to fill and I had to chill the water but other than that it's working great.

Great video, thanks! Is there any moisture removal consideration?

@Wingman115

6 жыл бұрын

I do need a better moisture trap for the compessor.

any word on duty cycle? Im looking for a low cost high PSI pump for air liqufication experiments using the linde cycle. most "reputable" pumps and air pressure multipliers are in the many thousands of dollars range. Not looking for 24/7 process duty, just want something that can run for an hour or a little more at a time without eating itself.

Haha just had a thought. You could also put a computer PC water cooling system on the bucket to cycle the water around and keep it cool.

@Wingman115

7 жыл бұрын

Great tip thanks for sharing.

@osbornephoto1955

6 жыл бұрын

This would never work. The amount of cooling necessary would take something like a motorcycle radiator and a water pump. Even that would probably not be enough for it would still get around 180-200 degrees. This compressor fills fast but that is also why it gets hot fast. There is no way around the heat when you are pushing air at this quantity and PSI. I find by putting ice in the bucket of water works best.

@gotindrachenhart

6 жыл бұрын

Could always get a small radiator of some kind to hook up, maybe an aluminum intercooler or even heater core from a scrap yard or even new if you can find one cheap. Hook it up as a loop then submerge the radiator into a bucket of water. Or heck, go full bore and get a full automotive radiator and a fan. Biggest issue would be hooking it up but I'm sure there are some radiators out there that could be adapted :)

@thingsdemystified

6 жыл бұрын

What do you mean this would never work? Of course it would work. Do you realize how powerful computers are? They're dumping hundreds of watts of energy, especially the overclocked CPUs. This pump uses about 900W, so it should be no problem at all for a computer water cooling system to dissipate that amount of heat. Remember, computer coolers cool the CPU to temperatures much cooler than what this pump can handle. Also, note how much water was in his bucket, and it wasn't even cooled. I have a triple 120mm setup I'm going to test when I get a pump like this. I have no doubt it will be more than enough to cool this pump.

@osbornephoto1955

6 жыл бұрын

Great...I can't wait to see your results.

why not use radiator fluid to cool down the compressor instead of water?

2 years ago you did this and said you would do a follow up in about 3 months. Where is it? I cant find it searching your videos under yong heng, did you title it something else or just didnt do it?

@Wingman115

4 жыл бұрын

No follow up yet. Life keeps me busy. Thanks for watching.

What kind oil did you use? Thanks

Hey I came across this post, looks great. Everyone is filling these up to the 4500 PSI but any time calculator on how long it would fill an emptyish tank (1000psi) to 3000PSI?

@Wingman115

6 жыл бұрын

Took me about One hour and 20 min when I filled a friends.

It's been about 2 years since you made the video. How much have you been using it and how is it holding up?

@billdesmet3929

2 жыл бұрын

Great Question 👍

@rWirthlin420

2 жыл бұрын

Yet no answer.

@bradfader691

Жыл бұрын

Mine lasted a month lol failed catastrophically.

Where do I get extra burst disk my compressor just arrived yesterday with no extra disk????

How hot did the water get, you need to check that to make sure your water is doing the job.

How long do you think the compressor will last? (I do not shoot much, this would be for me, no one else, so it would not be running much) Do you think it is quality? Is there anything else that would be needed to use? Thank you:)

@Wingman115

7 жыл бұрын

Treat it right and it should last a long time.

You are supposed to start the motor with both bleed valves open to prevent the stress on the motor, let it run for a second to warm up, then close the valves to begin filling, if you want to maximize lifespan of the compressor

i wonder about the water in the tank with no filter ,or the tiny filter i see guys useing much bigger filter ,i got mine works great put ice in the water with tuxing filter i use 3 filters

Exactly where did you order this pump? EBay shows several different prices. how much did you pay wirh shipping, if I may ask? Thanks, Dale

@Wingman115

6 жыл бұрын

I got mine on eBay..

hey Wingman115 , when you bleed the valve do you see any exes oil and water coming out the valve? im just wondering what passes through the line in the tank. it could be dangerous if oil goes through... after how many fills do you change the line filter?

@Wingman115

7 жыл бұрын

No oil when I start seeing moisture I swap out the filter.

@thingsdemystified

6 жыл бұрын

When I loosen the valve, liquid sprays out. It's definitely a good idea to run the pump without a tank connected to spray out the moisture when you're done.

I have ordered one and should receive it Wednesday God willing. wish me luck

@Wingman115

7 жыл бұрын

Take your time setting it up. If you have any questions shoot me a pm.

How much did you pay in import taxes? Or was that included in the price?

I just ordered this compressor. What machine oil should i buy for this???????

did you have any trouble with the quick disconnect when you recieved the pump?

@Wingman115

7 жыл бұрын

+Quentin Noah no works fine.

Are you guys using an extra Air Water Separator? Or is the one supplied sufficient?

@Wingman115

Жыл бұрын

I currently use an aftermarket one.