Yamaha v-max / venture vacuum carb membrane change
How to change the vacuum membrane on a v-max / venture / 535 without disassembling the slider. If you want to buy some, email me at rzubonja@gmail.com
How to change the vacuum membrane on a v-max / venture / 535 without disassembling the slider. If you want to buy some, email me at rzubonja@gmail.com
Пікірлер: 33
Thanx dude. Nice video. Love the "not so sharp side" part 😄. Blunt side is the proper term. 👍
Great job, One thing though, You have to mark the position of the little "ear" on the edge of the membrane and mach it with the new one, that will orient the holes at the bottom of the sliders correctly in the carburetor.
@bobeden5027
2 жыл бұрын
how should the holes in the bottom of the slide be aligned? I have 3 holes in mine. Any ideas?
Thank god I clicked on this video before following the destructive method suggested by those other guys. Mine was a bit easier and only took me a couple minutes. Thanks!
Excellent! Just what I was looking for . I was just about to take it apart as I couldn't see another way to replace .
Thank You for this video. I have just buy a new membranes for may new motorcycle Yamaha xs400 se. When I saw the instruction, that I need glue the membrane and top plastic ring. I was thinking, that’s not a good idea!!! You’re method is better than instruction because You not damage anything.
@donmaribras
4 жыл бұрын
Hi. Where did you get your membranes?
@pomonabill220
4 жыл бұрын
Where did you get the membranes???
I have also found that placing the slide in almost boiling water helps in both removal and replacing the diaphragm.
Hello from Canada. Thanks Ranko i needed to know that. I have to replace the membranes on my Yamaha Virago.
very nice! Thanks for the tips!.. blunt or dull side is fine! LOL you almost said dull... LOL
Goo vid. “Not sharp” = “Blunt” but I guess 5 years later you probably know that 😊
Thanks man. I do it with that way and its works. Ich habe mit diese Methode gemacht und ich schaffte. Λειτουργεί παιδιά, το δοκίμασα όπως λέει και πετυχε. Thanks!!!!!
Such huge fans over here @ #how2wrench Nice work!
Amazing! Thanks man
super video
Jedino mislim da je problem jer nije isto gdje će gledati ono ispupčenje na vrhu membrane. Ono bi trebalo biti u točno određenom položaju na klipu kako bi klip kada se instalira bio pravilno pozicioniran... hvala za video baš me čeka promjena jedne membrane...
Not sharp side of the knife is the dull side.
thank you !!
о русский) спасибо за отличное видео)
I have VMAX1200cc hard start ithink the starter can't rotate the cranckshaft
Any idea master?
Thanks!
use a credit card. or a shopping card..it/s much better
Where did you get the membrane?
👍
Pozdrav Ranko gdje se nalazite vi ,u Hr ili . Ja sam iz BiH trebalo bi mi staviti jednu membranu od Yamahe XV 500. Prije smo ljepili ljepilom al pojede se i pukne
@rankozubonja2354
3 жыл бұрын
Osijek
In English it is called the dull side.
Damnit. I wish I have watch this one b4 breaking the poly flare ring. Now I feel like an idiot....its impossible on some years to simply slide it in place some some say....forcing it in with the dull side of a thin knife will work much better....dangit.
Pozdrav Ranko, vidim da si majstor za zamenu membrana na VMax-u. Moze li neki kontakt?
@rankozubonja2354
4 жыл бұрын
Pozdrav, javi se na rzubonja@gmail.com
I used my thumbnail to push the rubber in.