Give the kid some credit, the seat was on perfect. 🌎🤣

I rode in Texas the other day and was having a grand ole time; the reverse gear was having issues, spitting and sputtering, and it backfired only in reverse. I went back up, and it died again. I tried to restart it like I had multiple times before, and it never started. Starting was louder than usual, so I thought something was off internally. I towed it home and went to looking and low, and that same intake boot popped off ever so slightly; I slipped it back on and tightened it up, and started up instantly. Good work figuring it out!

Its your Grizzly and Arctic Cat series that got me subscribed to your channel. I`ve watched both series like 4 times. Hope you do another atv series in the future.

"Hey don't kick that gas can over!" 🤣🤣🤣🤣🤣🤣 bro you got me rolling on the floor laughing

great! just had the same problem. thanks for the help

Hey, let the kid test drive it Dad ;- ) .....Great diagnosis ...

Steve, Great series of videos. I've basically gone step by step in rebuilding a 2000 Grizzly by watching your videos. How do i correct a rich running grizzly? Can i do this without removing the carb again?

@stevewatr

4 жыл бұрын

As I recall, there you cant get the throttle sleeve/needle assembly out without tilting the carburetor over. The height of that needle in reference to the sleeve changes the mixture. Raising needle makes it richer, lowering needle makes it leaner. Hope this helps.

Common problem. It took me a while to figure that one out. I even replaced that carb boot and it would still blow off. Thanks to EPA they have to be lean to meet emissions and that makes them pop back through the carb. Mine has a slider gate and when its not open enough it will blow the carb off the boot. I was told to drill the low speed jet out to richen it up a bit. But for now im fighting an no intermittent spark problem.

@clr1001

Жыл бұрын

I have not read all the comments so please forgive me if somebody already addressed this : If you haven't gotten your spark problem fixed yet, first put a new spark plug in it--it's a b*tch--18mm spark plug socket, it's way down in there, then get your multitester out and check your stator snap connects located under the left rear inside the frame by the left rear tire with your meter set to OHMS, per the Grizzly shop manual red/white should be 459-561 for your stator pickup button and green/brown should be 270-330 for your coils, i got an aftermarket stator and they wired it wrong so check your wires and wire colors, its working now tho, also I watched another content creator and they recommended grounding the battery to the frame with a heavy cable as an extra ground in case your stator tries to ground to the frame? I didn't know about that but I put extra ground wires on both my 1998 and 1999 Grizzlys anyway and hopefully it helps, good luck

This might be a stupid question but what's the difference in power between the 600 and the 660

@stevewatr

5 жыл бұрын

I don't know exactly, but I bet it wasn't very noticeable where it counts. Seems like a lot of these changes are for marketing purposes.

does any of your vids show air duct assembly pieces? my 01 grizzly 600 is missing the air duct assembly that connects to crankcase. im wanting to replace it but cant find a clear picture of what it looks like. if you can shed any light. id appreciate it.

@NLPYROFREAK13NLP

6 жыл бұрын

What's your email I'will send you a link

@1texasdad224

4 жыл бұрын

@@NLPYROFREAK13NLP I need help with my 600 I'm having the same problem

@NLPYROFREAK13NLP

4 жыл бұрын

@@1texasdad224 send a whatsapp to 0614059296

What year is your Grizzly? I think i have the same one. I cant get it to start because the starter is slipping and mine does not have the pull start like yours does. Is that an easy fix?

@stevewatr

5 жыл бұрын

Mines a 2000. I've found the pull starter to be useless. It's very hard to pull on this big of a motor. As for is it an easy fix? Shouldn't be too hard to diagnose. Start by making sure you have a good battery that's fully charged. Then pull the starter and see if it spins up okay, and is throwing out the pinion gear.

@BassemRashidi

5 жыл бұрын

@@stevewatr thank you for your prompt reply Steve! I was able to get it started a couple of times today with a new fresh battery. How ever I had a problem with the choke later on in the day and it wont start, then I figured out the choke issue and now I just hear a grinding sound in the flywheel when trying to start it like something in the starting mechanism below is not catching :/ and a sound of metals grinding every once in a while. Now the new battery is dead lol so I have to recharge it. Do you think low oil level may contribute to this? I need to figure out how to add oil as well because I can see that theres little to no motor oil in in the glass indicator. Fun...

@BassemRashidi

5 жыл бұрын

@@stevewatr I watched your video again just now and I noticed 2 things. 1. Just like yours, my carborator leaks fuel from a top hole where a hose should connect to. 2. Your son is wearing Red Sox gloves, are you guys in MA? Im in Milton Massachusetts!

We have a 660 that looks almost like yours. It need brakes, starter and carb job. It does go like stink tho. You can spin the tires at almost any speed.

@scrappy-watchentertainment3875

5 жыл бұрын

we have a 99' 600 and yeah there BEASTLY machines!! also have a Rhino 660 thing does like 72 on the road lol

Just realized I been running my grizzly with no oil dam near so yeah idk but it still run no problems then things are tanks I swear

Intake compression power and exhaust.

Looking for oil dipstick on 99 Grizzly

@haroldalarie1220

4 жыл бұрын

No dip stick for oil just where your left foot is on bike. Take botton covet off and bent down will see a class tell you if oil is full

I gave up wasting time and money on old quads. I just bought brand new and love turning the key and knowing its gunna start & get me back home

,,,,,,,,,,, PLease STOP saying ADIN,,, The Boot is OLD AND ROTTEN