To all the people who have leaking trim seals and think this video is showing you how stop your leak with the seal he replaced, it's not. He only replaced the dust seal, the seal that holds the trim fluid and pressure is down below the dust seal inside the cap and he never replaced it and it's much more important than the seal he shows in the video. Make sure you buy ALL the seals and replace them or you're wasting your time like this guy just did.

I used your pipe trick today to loosen my caps on my Yamaha 150. Worked like a charm! Thanks for all of the great tips and videos Eric. I’m glad I found your channel!

@johnnnyg100

Жыл бұрын

Me too the tool kept slipping out, I couldn't keep it from popping out. Put a pipe on like TheBoatGuy suggested and it took some extra strength but the cap spun without slipping! Thanks!!

I love this video, so much. There have to be at least two dozen others out there, all with (I'm sure) pluses and minuses, but you made this task so easy to understand and I'm fully confident now that I can do this repair myself. Thank you!

This is EXACTLY what I needed to watch. Currently doing this exact job. Good descriptions and you made it look easy. Great job bro 😎

The motor you sold me is running like charm eric ,was a pleasure meeting you !!! yamaha 115 4 stroke. thank you for share

Great video, now I have already changed the seals, thanks

Thank you for the very informative video. With your help, I replaced the seal and O-rings for my trim/tilt today on my Yamaha F250. I used your pipe trick as my caps were on extremely tight. My caps had a retainer clip in a groove I had to remove first. Thanks again.

Yes you did a great job 👍 on The video easy to follow Thanks for all the part numbers on the seals

The top seal is just a static wiper seal the oil is bypassing on the piston seal. If there was any pressure on that seal it would just pop out.

Excellent video, great camera work, excellent commentary , nice and clear and the tool link is a nice touch.

Great vid Eric. I just replaced my trim seals ,,watched this before,,getting out the old seals from the caps would have been a challenge if I didn't see your vid, thx.

Nice 👍 even though it's old it's still very helpful🤓 makes me feel like I'm a you tube marine mechanic thanks to you🤠👍

Thanks!

Since you replace the cap seals, why did you not replace the piston seals on the rod as well?

I wished you were u here helping me

Just ordered that tool a couple of days ago, looking forward to using it. My system is different, but the principal is the same. Thanks for the video...

@TCross-xq4kc

3 жыл бұрын

What size tool did you wind up getting? I see different sizes. Thanks

Great job.....ciao

Nice video. Always good information on this channel. Thanks.

Just found your channel. Love it! Please keep at it. You videos are so helpful. Thanks

👍👍

You look so much like my Sone. Handsome man. Thanks for the info on those seals. I have to replace mine soon. Thank you. I subscribed to your channel.

Good info tx

Thank you! That pipe trick saved me pn my -96 70hp 6h3/6h1 combo. Thanks!

@drewdavies1872

Жыл бұрын

How do I know when I have to service my trim tabs?

Have you ever done a video on servicing / seal replacement for the tilt cylinder on the yamaha 90 2 stroke? Getting ready to tackle that soon. Thx.

@drewdavies1872

7 ай бұрын

I am working on mine right now. The the Trim side of the project was easy. I cannot figure out how to get the large trim ram fixed. I can’t figure out how to take apart the sub assembly, to put in new seals, and stop the leak. Any luck?

Thank you very much. Great clear precise video.

I have a 2013 Yamaha F70 4 stroke with a single ram tilt that is leaking badly. My cap does not have holes on it. Could I send a picture to get your opinion on how to remove?

Thanks for the video! I successfully changed my seals out this morning.

@russudvp

4 жыл бұрын

Did you change out the middle one?

@jayboogie27

4 жыл бұрын

@@russudvp Negative. However, I now at least have proper pin/spanner wrench if I need to get in there.

@russudvp

4 жыл бұрын

@@jayboogie27 how do I send you a picture of what I'm trying to do. I'm stumped.

Thank you very much! Easy and very well explained!

THANKS ..

great video bloke.

What a fantastic video. Thank you.

Place Motor so the fill hole is 90 degrees vertical to horizontal line. Remove fill hole plug fill until overflow. Install fill hole plug Cycle System several times. return motor to Vertical position remove fill hole plug check fluid level top off as needed. Apply small amount of thread lock to plug install fill hole plug do not over tighten

One other question -- I didn't see a video on the process for swapping out a tilt/trim *motor* on your site. Or is that such a trivial matter that you didn't need to create one?

I need some parts for a 1995 Yamaha 75hp , 2 stroke . You have any parts for one I’m located in Davenport, Florida

Love this video. Any chance you could mention a part number for that spanner tool you used?

@jerrywatts3784

3 жыл бұрын

Very informative video thanks

Gday mate i know this is an old video but i have an 90 40hp that has the same trim and tilt system on it this is invaluable information for me as mine is leaking too , those trim spanners are about 80.00 here in aus . Now i know what model to look at as none of the 40hp have this trim system (maybe of another motor) i will be able to get the parts i need to fix it , the trim motor is really sad covered in rust but still works so there is another 400.00 but with the cost of a new motor at around 8000.00 im gonna try to keep this one going .

The caps don't have to be super tight, just a little past snug. The oring and the seal are the seal. Also don't put teflon tape on the threads.

I love your videos man!! Very informative and interesting. I have searched the tube for videos describing a timing belt change. Preferably on a four stroke Yamaha outboard but I can’t find any. Can you please make one when you get at opportunity?? /Daniel from Växjö Sweden

Nice explaining vids you do ... 10 outa 10 ☝️

Great video well done 👍

hi eric i'm trying to remove the ( MANUAL RELEASE SCREW) and there is a snap ring i have to get out ..have some tips... Yamaha 1987 115ETLH

Appreciate the trim seal replacement video & link to the trim tool - thanks Eric!

@psi23k

5 жыл бұрын

Search ebay, tilt seal tool. Should come up, including the one he used. About $100aud

! thank you

can you use thoose rings and seals on a yamaha around 2000 model trim too

so I would have to jack up the trailer that my boat is on to get the canister that holds the fluid in to get it level? also I noticed you didn't mention the longer rod in the rear of the ones you replaced the seals on, do we need to change that one as well? Thanks

That info on the tool would be appreciated

hey why would I have the right trim seal keep popping out after I replaced them?

Awesome video, thanks for the help

Just wondering if you have any videos on how to change an Upper Crankshaft Seal on an outboard? I have oil leaking under my fly wheel. Thanks

Where did you get the tool from ? I need one like yours that is adjustable and cannot find one !!

Is this for a Yamaha "6h1-10" or a 6h1-somethings else? Can't see in the video

I have a Evinrude 84 can I put dot 3 brake fluid in it I use it on my hydraulic jack

@samtate1260

3 жыл бұрын

@assassinlexx yeah I called The marina and they said they use power steering fluid if it’s just because it’s little low also herd Marvel mystery oil is good to from a guy working on outbords his whole life

@samtate1260

3 жыл бұрын

@assassinlexx thank you and happy boating to you also

i like you video,,

Nice work! thank you

I surely don't know for sure but most hydraulic systems are designed to measure the fluid in the reservoir when all hydraulic cylinders are compressed. It seems possible the way you're doing it you could easily get too much in the system? Of course access on the system you're working on would be a real pain if that motor was all the way down so possibly you're doing it correctly and it is designed that way?

@The.Norwegian

5 жыл бұрын

The procedure is to tilt the motor all the way up and then fill up the reservoir until the oil spills out, then run the engine all the way up and down a couple times and check again.

Love those Yamaha's.....

@bobbitlawrence8903

3 жыл бұрын

Thank you . Very informative. My 70 ya my has the same trim tilt. When trimming , there seems to be some delays before it moves, something like 3 to 4 secs. Is this normal ?

@macjank1615

3 жыл бұрын

Air

Do I need a different bracket to install a power trim unit Yamaha on a non original power trim bracket?

thanks for a good viedo

If one of the cylinders have water in It how do you get It cleaned out? No way to push oil thru it until it’s clean?

I have this same engine and some how while I was using it this weekend I lost one of the pistons for the tilt and trim. Any idea if I can still get replacements?

Love the videos thank you! This helped me with my 2001 250 Saltwater series. Do you have any recommendations for Yamaha used parts dealers online or I can call? There has to be a used Yamaha parts store . I am unable to locate one here in Texas.

Handsome outboard- great video

Dla potomnych. Dobra robota.

Very informative thanks for the video.

Same for a 115 two stroke?

How do I get to the center seal. I have the pistol rod in my hand, I'm not sure how to get the end off. There is no screw on the end, but I see a small pin. Does the pin need to come out? I have a 1988 90ETLG Yamaha. Thank you

yamaha 85hp same?

My trim rams won't compress. Tilt works fine. Any suggestions? Thanks Bruce

Hey Eric how do you replace the center trim seal on a 2001 90 Yamaha. Mine is shot.

Great video. Thanks

Good video. Thanks!

What about the main rod seal is that more difficult

nice Yamaha-great vid

Hi there :) great Video! I have an Yamaha F40 BETL 2004 and need such like Tool you promote. Cant find it in Germany. Maybe you have some web links for me to find Tool. Distance needs to be 38milimetres and pins with 4milimitres. Thanks in Advance, York

How much for that 90

Cool thanks mate ur a legend

I have the s as me motor. We hat spanner wrench is that? Ive been trying to get my caps off for awhile now!

Hey mate, what microphone are you using in your videos?

Hi, sorry for the question, do you think you can put a trim on a Yamaha 25 j from 1989? Hello

Need name model # of wrench you're using

Do you know where i can get a tiller for a 1989 90hp yamaha

Will that Trim tool you recommend works for the tilt cap too?

@keywasted289

2 жыл бұрын

Yes it will. I did both my trim tilt and steering cylinder today with the same tool

@edruof4565

2 жыл бұрын

What is the name of the tool?

Excelente

That trim tool my friend is called a spanner. Although that one's pretty nice the way it's adjustable

Same method for a 2001 Johnson 50 horse outboard?

Aqui no Brasil custa 1200 reais para fazer este serviço

Nice video just wanna ask some question please.. the oil for the lower unit it’s the same oil to use for the trim seal ??please answer I’m from New Zealand.. Cheers..

@keywasted289

2 жыл бұрын

No

thank you 👍🎣

Gday Eric a fan from Australia just wondering which size pin are you using the 1/8th or the 3/16th..... cheers from Oz

Where do I Locate The Cap remover?

I noticed that many of the of the outboards in your videos are Yamahas. Is that a coincidence or do you seek out Yamaha motors?

@MrSupermugen

5 жыл бұрын

yamaha = best on market...

@accordino86

5 жыл бұрын

@@MrSupermugen is correct!

Thanks for your videos. How do you like living in Florida? I'm retired would love to have a boat.

hey mate you still on this site i got a question

Thanks a lot for a video!

Where did you get the cap remover tool from?

Hey Eric im looking for a good Yamaha 50 hp hit me up if you have one.

@johnnyb6052

5 жыл бұрын

U still looking for a 50hp two stroke 2007 Yamaha. I have one for sale

Excellent ~~~~

For someone that calls himself TheBoatGuy you did not change the seals. You only changed the wipers buddy.

No specific torque required?

Helloo