This was me refilling my tilt and trim on my Yamaha F115.
Жүктеу.....
Пікірлер: 21
@romer431 Жыл бұрын
Thank you. Thomas Denmark 🇩🇰🇺🇸
@gibso35f Жыл бұрын
To folks looking this up- you can use normal automatic transmission fluid for this if needed.. check your fluids about once a week if you’re an avid boater 🤙🏼
@foff-6669 ай бұрын
@ 1:08 that is such a danergous thing to do - you can EASILY lose a finger. hydraulics let go when they hit air bubbles. nice.
@JA-gx4hb Жыл бұрын
Thanks for posting. Now do a video on changing those leaky seals.
@SWFLFISH
Жыл бұрын
I did , kzread.info/dash/bejne/d42dp6Wiocardso.html
@SWFLFISH
Жыл бұрын
Thanks for watching 🤙
@guebsiali8875 Жыл бұрын
What caused the fuel pump to fail? Because in the span of 6 months, he changed three times, and I don't know why
@SWFLFISH
Жыл бұрын
Internal float was not sending the signal, just got old I guess
@coreywallace1362 Жыл бұрын
Dumb question same motor once it hits the trim rods is it normal to be that slow going to trim down to transom feel like mine is super slow
@SWFLFISH
Жыл бұрын
Hey Corey , yea mine is slow too, it’s supposed to be slow , then the big one goes faster
@gibso35f
Жыл бұрын
Yea , - as you already know.. but the REASONING for this is when you are that low in trim, the corrections are smaller due to the speeds you may be at for low trim( on plane perhaps) so your trim inputs don’t “over correct” per se
@chriscollins4539 Жыл бұрын
Thank you for the video? My question is why would it be low? Did you have a leaking seal?
@SWFLFISH
Жыл бұрын
Yes I did , leaking right by the cylinder and the top of the reservoir too.
@thomasjohnson976828 күн бұрын
thanks my issue too.
@bullfighter18013 ай бұрын
What is the plastic adapter fitting that screws on to the quart bottle? Thank you
@SWFLFISH
3 ай бұрын
It came with the bottle when I purchased it
@Cotton603 Жыл бұрын
When i trim down a ton of foamy fluid comes out the top of the cylinder is that normal
Пікірлер: 21
Thank you. Thomas Denmark 🇩🇰🇺🇸
To folks looking this up- you can use normal automatic transmission fluid for this if needed.. check your fluids about once a week if you’re an avid boater 🤙🏼
@ 1:08 that is such a danergous thing to do - you can EASILY lose a finger. hydraulics let go when they hit air bubbles. nice.
Thanks for posting. Now do a video on changing those leaky seals.
@SWFLFISH
Жыл бұрын
I did , kzread.info/dash/bejne/d42dp6Wiocardso.html
@SWFLFISH
Жыл бұрын
Thanks for watching 🤙
What caused the fuel pump to fail? Because in the span of 6 months, he changed three times, and I don't know why
@SWFLFISH
Жыл бұрын
Internal float was not sending the signal, just got old I guess
Dumb question same motor once it hits the trim rods is it normal to be that slow going to trim down to transom feel like mine is super slow
@SWFLFISH
Жыл бұрын
Hey Corey , yea mine is slow too, it’s supposed to be slow , then the big one goes faster
@gibso35f
Жыл бұрын
Yea , - as you already know.. but the REASONING for this is when you are that low in trim, the corrections are smaller due to the speeds you may be at for low trim( on plane perhaps) so your trim inputs don’t “over correct” per se
Thank you for the video? My question is why would it be low? Did you have a leaking seal?
@SWFLFISH
Жыл бұрын
Yes I did , leaking right by the cylinder and the top of the reservoir too.
thanks my issue too.
What is the plastic adapter fitting that screws on to the quart bottle? Thank you
@SWFLFISH
3 ай бұрын
It came with the bottle when I purchased it
When i trim down a ton of foamy fluid comes out the top of the cylinder is that normal
@SWFLFISH
Жыл бұрын
No it’s not , your seal is broken and leaking
How do you know when to stop filling?
@SWFLFISH
10 ай бұрын
It will pour out
No