This is awesome that you have come out with a complete kit, totally worth the price vs. using rusty junkyard parts and headaches of figuring out the steering setup.

Now, what about sway bar mounts?

Can hardly wait for this kit to come out! My lady’s XJ badly needs the upgrade! Well worth the buy rather than the junkyard method! Keep up the great work guys!

@core4x4fab

Жыл бұрын

Thank you! We will announce when it is available! We are making final adjustments to make sure the kit is good to go!

@SuperDad1776

Жыл бұрын

@@core4x4fab fantastic! Looking forward to it

I m a little worried that you didn't weld the spacers to the knuckles...if you look the hub only seats in the knuckle about a quarter inch and you need that secure, otherwise the bolts are the only thing holding on hub, brakes and larger tires. and a tip for the tapered slugs is put a tack weld to hold for disassembly later or they may come out with tie rod end

@flyguyeddy

7 ай бұрын

Seems like most people only do 1" welds on the spacer, i dont imagine thats all THAT strong. What about just using grade8 bolts?

That hub spacer is carrying the load of the hub/unit bearing. It should be welded to the knuckle.

Excellent thanks I have a XJ , MJ and TJ this will help all of them 👍

I don’t see this kit listed under the Xj

Do you sell just the trackbar bracket orange one?

Bumpsteer; its gotta be pretty bad considering how short your track bar is. Being parallel is a big part but length is important too. Is there an option to mount the track bar in front of the coil to get the length closer to the same as the draglink?

Also are you using longer hub bolts? 16:16

Do you know if this kit works with a rubicon express track bar bracket? My current set up has a frame brace that I would really like to keep.

Hello there! will this kit clear 15 inch rims with 3.75 back spacing???

Is not welding the spacers really, ok? 13:33 Everyone says it's a must..... I'd love to hear from anyone who has just placed them and not welded them in. Especially if a long-term opinion .....

We’re did you get the bushing inserts for the knuckles? I did this swap and mine seem thinner and don’t weld in

Is the unibody side track bar bracket compatible with frame stiffeners?

Can you get ball joints with knurling?

I really like the kit looks really will built. Iam running your short arms on my wj with 8 inch lift and the wife's wj has 4inch lift with your short arms. So now we are waiting to see if you come out with a long arm kit for the wj .

@core4x4fab

Жыл бұрын

Glad you’re loving the products on your vehicle! Thank you for your business. We aim to make this kit top quality and easy to use with everything you need. We are finalizing products and design and should have it available on our site shortly!

Since the XJ front is basically a TJ front, this should work just as well on that platform. I use a XJ front in my TJs due to using adjustable (1 TJ) Core4x4 control arms (way to align caster, XJ is off frame, TJ is off axle bracket), and high pinion layout. Another thought, since the WJ knuckle is a high steer drag link, was there ever a RHD WJ? Cause, similarly, the JK knuckles are mirror to the WJ and JKs had RHD so that, you could relatively due a high steer setup (over the knuckle) on the drag link and then tie that to a high steer (another over the knuckle) tie rod, but using a bracket to make it even higher between the 2 steering points on the knuckle. Since you added a 'decorative' plate on the front corner, too bad didn't add a skid plate to the lower CA axle brackets and the upper passenger. Lowers tend to rip off or tear off. Upper CA bracket tends to fold or tear off the tube.

going to buy this kit. My only question is about the new track bar? why is it mounted with the bend facing up? Aren't you worried it will hit the oil pan at full compression, and can you mount it pointing down?

@core4x4fab

10 ай бұрын

Good question! The slight bend is for the diff cover clearance. At full compression at this height there is ample room above the track bar.

@emtjc8465

10 ай бұрын

Thank you for the reply. I just placed my order yesterday. Can't wait to get this on the Jeep.@@core4x4fab

Ball park price?

I don't even see this steering listed under the jeep xj. Also regarding your tier 4 long arm kit, there are no details. What is the thickness of plate used for the cross member? I assume the center section is removable to allow servicing trans etc without taking off the arms. Can the cross member work with frame stiffeners that are already installed? Does the tier 4 kit come with Johnny joints to replace the pressed in bushings on the axle side? Are the arms designed for high clearance? What is the minimum lift height for your long arm kit to ensure no contact upon up travel? How is the clearance of your cross member? How low does it hang below the bottom of the frame rails? Do you guys offer a skid plate that will integrate with the cross member or plan too? I'm in the market for a 4 link lift and I can't find much if any info on your guys kit.

@core4x4fab

Жыл бұрын

Hey Jon, thanks for the questions! The plate is all 1/4 inch on the brackets and the crossmember. The crossmember itself is two separate 1/4 inch plates welded together, so in most places there is 1/2 inch of steel between you and the ground. The kit can work with frame stiffeners, we slotted the frame brackets to allow for that. You will need to clearance a little more on the inside of your frame rail though. This kit does really well on LCG builds and we have had customers run it on as little as 2 inches of lift. There may be more trimming around your factory upper mounts for clearance on the arms, but generally the range of motion is there. Currently there is not a skid plate for the transfer case, but we are looking to add one to this kit. The crossmember itself has really good clearance and was designed as a "high clearance" kit.

@jmangus83

Жыл бұрын

@@core4x4fab what about the johnny joints on the axle side of the upper arms?

@core4x4fab

Жыл бұрын

@@jmangus83 That is an optional upgrade. The kit part number is CE-9102K, and we will be adding it as an option when you order the kit

@jmangus83

Жыл бұрын

@@core4x4fab so that's optional on top of buying the tier 4 kit? It doesn't come with?

10:23 what are those things in your ears? Headphones or for splatter? any info would be great thank you!

@core4x4fab

Жыл бұрын

They are noise canceling ear buds for the noise

@TexasRedneck

Жыл бұрын

@@core4x4fab aww ok wasn’t sure if they were for the weld splatter.

I am interested in this kit. I do not see a link on your site for it. Also, what are the TREs and rotors from? I assume they are OEM for something, would like to know that I can go down to the local parts store and get replacements when they wear out. Thanks!

@core4x4fab

Жыл бұрын

It is not yet available on our site, we are making minor adjustments to make sure the kit is ready to go! We will announce when it is available. We get our Tire Rod ends from either Rare parts inc :)

@benjaminreinhardt259

Жыл бұрын

@@core4x4fab My question was not where you source your TREs and rotors, it was where I can source replacements when they wear out. I've had the jeep 10 years now and plan to have it another 10. I do not want to install wear items that are custom order. Are they OEM from another vehicle or custom?

I looked at your website and couldn't find the WJ knuckle swap kit for the XJ.

@core4x4fab

Жыл бұрын

It is not available yet! We are making fine adjustments to the kit to make sure it is 100% ready!

@TexasRedneck

Жыл бұрын

@@core4x4fab awesome! Was worried I might have missed it.

Anybody got the part number for the ford explorer brake rotors

@christianperaza4360

10 ай бұрын

PR64099L PR64099R, works perfect for me, just need to grind a bit of the hub bearing flange, use the 01-06 tj hubs

Are the brake rotors and hubs from the WJ also?

@1unkn0wn

Жыл бұрын

I believe that: -Rotors are from an explorer for 5x4.5 without drilling -Hubs are XJ just turned down a bit

@danhambrick6331

Жыл бұрын

I noticed that you put a spacer on the hub but not the caliper bracket.Why?

@core4x4fab

Жыл бұрын

@@danhambrick6331 with the correct caliper and bracket you don't need a spacer for that bracket.

@core4x4fab

Жыл бұрын

@@1unkn0wn Exactly! Rotors are from the '02 Explorer Sprotrac and they are XJ hubs with a little bit shaved off

@jamescassada3787

Жыл бұрын

@@core4x4fab What part of the hub need to be shaved off a litte?