You’ve become my favorite teacher for electronics repair. Straight to the point, always honest, no bullshit.

U9E2 is a mosfet driver IC and usually burns out the little resistor above when it goes bad, the resistor acts as a fuse and prevents more damage to the board. The part number for that component is NCP5901BMNTBG

@TheCod3r

3 жыл бұрын

Also 51916 is a ddr3 memory power management ic (TPS51916) and regularly goes bad

@TheCod3r

3 жыл бұрын

@@graphicscardtech3167 yeah they're a little tricky to find but they are available 😃

@TheCod3r

3 жыл бұрын

@@graphicscardtech3167 yeah I also buy them in bulk because it's cheaper and I fix hundreds on xbox one s consoles with the same problem lol

@Anonymous-nh5dt

3 жыл бұрын

@@TheCod3r do you have an online store front, I have this issue with an xbox one s console and want it fixed. I didn't spill anything on it but has similar issue.

@B9NE

3 жыл бұрын

The man, the myth, the cod3r lol. Freakin legend man.

Thank you brother. Cause of you I just fixed my son's Xbox one s that thought was doomed. Wish I could buy you a 🍺. Thank man.

You are a true repair savvy. Thank you for more inspiring and encouraging lessons. The best wishes from México

It’s always the best you bring out both your work n knowledge

@expertnugget

3 жыл бұрын

Its like he does it as a job or something

Long time man good video I've been watching alot of these lately

Totally amazing I just love the way you do videos Very informative and amazing skills! Keep them coming

1:58 thanks for the info.

Every video im amazed amazing job!

Really nice work. Well done.

This is the time when we make the device work more soon afterwards we receive a bucket of cold water when we realize that there was no image. More and still these are bones of the trade. congratulations you are a great professional ...

Best of luck and I hope you get it working today!

I have this exact job on the bench currently, interested to see what your fault is and if it's the same on this one.. I also had a blown R9D30 resistor, and a faulty transistor next to it on top of the 2 chips here, took me ages to find it!

Nice video as always. Would an ultrasonic cleaner be advisable due to the liquid spill?

You will find out because you are the master in this

did you try the button combination to reset the display settings (might have been set to 120 hz and or 4k)

He makes it look easy.

@vfr01

3 жыл бұрын

It is easy

Ever try an ultrasonic cleaner? I have revived/repaired MacBook logic boards with just running it thru there. Works especially well (50% of the time) with any boards without any burn marks. Corrosion is blasted away with osolating ultrasonic waves. 5 min, then rinse with 90% isopropyl alcohol and then dry with air compressor and let sit overnight. Board looks good as new and also eliminates all corrosion issues.

This is some super cool stuff I wanna learn about the tools u used during this video

@vgrepairs

3 жыл бұрын

Solder, iron, quik brand hot air station, amtech Flux.

@vgrepairs

3 жыл бұрын

Microscope

I hate leaving a job in full flow to come back to it. 👍🇬🇧

I'm not surprised that the fixes didn't work, the board was still caked with what ever was spilled on it. The board once it was first looked over and saw where the damage looked to be, should have been washed over with alcohol to clean it. Then reflow the solder.

@tayooo1000

3 жыл бұрын

he needs a ultrasonic cleaner

@jacruga

3 жыл бұрын

Correct, he did not clean all that mess how it will work with some liquid working probably as a conductor .

@maklogetrich2378

3 жыл бұрын

exactly, I was wondering too, why is he not cleaning all the liquid

@tomcadero9875

3 жыл бұрын

Lol..look at all of these "experts".

@atomic4l

3 жыл бұрын

@@tomcadero9875 Used to working in console/pc repair for over 15 years before I moved on to Network specialist for a UK telecoms company, but what do I know?

Would’ve been interesting to see the board under a thermal camera. Side note try a different HDD, a bad one may cause a no signal although I doubt this is the case here.

That's why I drink 70 proof vodka now. A spill won't destroy electronics.

@tayooo1000

3 жыл бұрын

this man is a genius

@melplishka5978

3 жыл бұрын

Do what I do. I make my own alcohol with no methanol lol. It’s methanol that gives you hangovers and also absorbs water lol.

Exactly what I need to be watching at 4am.

On old board letters on chip were AZE, and 1 was down left, while on donor board letters on chip were AZH and 1 was upper left

Nice job thank you Sir

Great video👍.did you find fault? Gues hdmi controler dead.let me know if you fix it.cheers

I have the same power problem with my xbox one x. Barely used it. No water exposure. It was in a Gaems case between my legs while I was opening a door and it fell like 2 or 3 inches and now it powers on for barely enough time to eject the disk that was in it. Wondering if a chip had weak solder or something after watching this. I'm not really equipped to do what you did. it's a shame because I barely used that xbox for almost a year and I finally start using it again and this happens. One day I might try to find a repair shop like yours

I bet it’s the video settings. It could be set to 4K.

@alejandros1578

3 жыл бұрын

I agree. Special when you said the first monitor showed out of range. I do not have the quick 2 buttons to press to reset it. Hopefully you can see these messages before taking the whole thing apart again.

Where do you get the capacitors and other components on the motherboard?

And this kids is why you don't keep liquids near your electronics

It should cleaned before start soldering right ?

I love your channel, but during this video, the youtube injected TWO commercials by 2/3 of the video!!! If the add is at the end or even at the beginning, that is OK. THANKS AGAIN!!!

Where do you get the metal tips for you solder paste and what size are they I can't find a good size anywhere most are too small

Thanks so much. I have the same 1 at my shop.. i bought to part out

Good job.

are you accepting new clients? i’m having the same problem, very sad.

What temperature do you set your hot air gun to desoder the chips?

I love u r work style Super

to check if retimer issue hold the eject button when you power on until it beeps a second time. if boots into 480 low resolution mode its the ic bad

How much did you charge the customer for this job? I had a power surge from a lighting storm

If possible please share your method of diagnosis.

Ya like the guy below said hold eject and press power and hold them both for about 6 seconds resets resolution to 680 i have to do that sometimes after a port and retimer replacement no clue why but is what it is!!! Worth a shot!

How are you able to tell there’s no short if you only test one side of the capacitor?

lol, thumbnail made it look like a happy ending.

@tarupam1paru586

3 жыл бұрын

plot twist

what is your soldering temperature?

How did you do that, it's amazing? I have an Xbox one x coming in the mail and need a person of your expertise to do that but where to look is a mystery.

Sir can u make an online coaching class for this topic exclusive. love from India

@scottdrew306

3 жыл бұрын

Check their website, they do trainings

Which solder paste and soldering iron u r using kindly reply sir

This is quality repair,i really enjoyed this video

No follow up video ?

How is it when you receive a very dirty board, you do not clean it of debris, after noting areas of concern??? Very often those bits of debris are moist, and that can cause problems on a continuing basis. There are various liquids in pressurised cans that are electronic cleaners.

You have to reset the display resolution in order to work on lower spec tv

@shashu1999

3 жыл бұрын

How to do it?

Out of range HDMI means the display can't handle the incoming signal settings. XBOX One can do 4K and if it is set for that resolution then any display connected to the console that can't handle the incoming signal resolution will give off that message. I'd just like to know what chips you replaced so I can fix mine.

How much would it cost to get it fixed

Does your solder station make a difference I could not get mine to melt the solder

hi what flux u use ...brand for re balling?

My Xbox is doing the same thing, how much would it cost to have this done?

whats the difference bewteen the 2 flux u use?

So, did u fix hdmi signal on it?

Having the same problem, mosfets check out ok, can not see any other issue except for the usb port in front, looks like someone tried to repair with a new one, i dont see solder all the way threw the hols in the pcb...... could that throw a short and shut down issue?

I am testing the same thing on a regular xbox one motherboard, all the mosfets are apparently okay, but when I test voltage the mosfets are only receiving/outputting 0.2V! Any clues what the problem might be?

Halo sar.u r a.genius .difrent style ok repair.god bless u.u r smile is good

Do you just buy a lot of replacement chips or do you scavenge them?

How do you get rid of the glare?

The Xbox cannot display the signal as the resolution is too high for your display. You can reset it by holding a few buttons as far as I can tell. I think it's the power and eject button for 10 secs

Hello, I was wondering if it is always going to be an issue with the motherboard when an Xbox does that; turning off immediately? or could it also be the power supply? My Series S does that.

Why didn’t you just test the chips before replacing them?

Nice job and video

I just fixed "won't come on or when it does it shuts off again" with taking off thr front bezel on a server and snapping it on the right way.

My xbox one s power supply went bad from lightning a while back so I ordered a new one. When I went to turn it on it cut on and right off. I noticed I broke the power button off of the pcb board so I ordered a new one. Just installed the new one and it still won't stay on. I have no idea what to try now

How much do you charge to send a mother board to to get it fixed

1:35 you touch one side of the capasitor. i saw this in few videos expected you tell where is the other prop. :) i hear the beep but where do you touch the other prop?

how much did cost to repair ?

Awesome ✌️✌️✌️

Have a similar issue on my bench right now. They took it to UBREAKIFIX and they ran it through an ultrasonic without inspecting, so finding the issue is proving troublesome. The standard mosfet failure is not my issue - all test ok. A bit of a head scratcher that I admittedly have set aside for other work. Will have to re-visit.

Hello! Brother, can you tell me your shop location?

Mine is doing the same thing. I didn’t spill anything on it. Now what?

Can you do a part two

what is that gel 4:24?

Had a one s doing that to me after changing the hdmi retiming chip. Pressed the sync and power then released the power. Was doing this because the resolution output for my monitor was wrong.

@ownenk

3 жыл бұрын

did you ever find a fix? im having the same problem

love this Stuff

Once the chip is off the board what do you use to keep the new chip stuck to the board I got a hot air station in flux low melt wire but it keep sliding all over the place 😢😭😭

Wiat did it work or not.?

When are doing the second part/completion for this console???

@tayooo1000

3 жыл бұрын

yea right that thing is toast now

Hello Sir,I opened my xbox one s and by the time I was putting the Main case the white plastic one The power button switch on the board came off and I just want to know if what's the name of that kind of switch so that I can look it up online or is there any alternatives switches that I can use for the board?? I live here in the Philippines and I think it will be really hard for me to find the exact switch on the board to use Hope you can see this Sir, Thank you

Hi im a huge fan of your doings im from philippines. I want to ask what flux you usually use and flux cleaner i want to practice to solder im an IT student and i want to learn more i cant buy on your merch coz i dont have cards to pay . Thankyouu in advance 🥰

Mine was struck by lightning I took it apart and I see no damage anywhere it powers on the light comes on then cuts back off spent hours just cutting it on to just cut back off I swapped the battery back because mine wouldn't power on at all to my friends his was struck to but his power box lights mine up to just cut back off idk what else to do

Ya did the do. It's all anyone can (and should) do. You can't overlook the care & feeding of your office's #1 asset. Without it... you are both lost. Eat/Sleep/Repeat. And thank God you enjoy your chosen profession. So few people have that luxury. You make a measurable difference every day ❤

The board still had flux residue and spillages still on it when retested.

you should get an ultrasonic cleaner.

Id love to work and learn from you.

do you have a video repairing xbox one x? My does not turn off and I know its not a liquid issue. I was going to replace power supply but now I have seen the south bridge issue of them going bad. Help Thanks

4:48 How do you get rid of the glare, looks so much better. I have issues with that and my microscope!

@gillsejusbates6938

2 жыл бұрын

turn on/off the light source of the microscope, you can find it on his website shop

Saved me $40-$100 on new controller... Working like new 0 drift on cod with deadzone at like .05 was between .2 and .3 on deadzone 💪🏾💪🏾💪🏾

Mine began doing this after I got it repaired, though it would turn on eventually.

Hi good teacher?, l wanna ask You what can l do for my laptop which crushing operating system after to install it, they happened after 1 or 2 mouths.

4:54 image quality is great, but 11:42 is greater, guess not that great.

Yeah it sounds WAY TOO GOOD to be true.

It work or not hdmi broken????