WP8066184 - Replacing Your Dryer's Motor Pulley - AP6011686, PS11744884
Тәжірибелік нұсқаулар және стиль
Part WP8066184 can be found at www.pcappliancerepair.com/inqu...
The Motor Pulley secures the belt to the motor. You may need to replace the Motor Pulley if yours is broken which is causing it not to spin.
Today, Jordan from Point & Click Appliance Repair will take you step by step through this repair so you can learn how to replace the Motor Pulley (part number WP80661840) in a Whirlpool Dryer by yourself.
Part number WP8066184 replaces AP6011686, 3389627, 3394341, 3401143, 694871, 8066184, 8578565, PS11744884, W10290531, W10299847, W10402909, WP8066184VP
WARNING: Before starting any repair, always make sure that the appliance is completely disconnected from the power source by unplugging it.
Tools Needed:
5/16 nut driver
Flathead screw driver
Phillips head screwdriver
Putty knife
3/16 wrench
Channel locks
Stepy-by-step how-to instructions for replacing he Motor Pulley (part number WP80661840) in a Whirlpool Dryer.
1. Disconnect dryer from its power source
2. Remove the lint filter
3. Remove 2 screws with your Philips head screwdriver
4. Remove the dryer lid with your putty knife
5. Disconnect the wire harness
6. Remove the two screws holding in the front panel
7. Remove the front panel
8. Pull the belt along the pulley wheel and then bring the belt around the motor shaft.
9. With your flathead screwdriver press down on the clip to remove the motor pulley
10. With the 3/16 wrench hold down on the motor wheel and on the back with a pair of channel locks squeeze down and unscrew the motor pulley
11. Screw on your new oem replacement motor pulley
12. With the 3/16 wrench hold down on the motor wheel and on the back with a pair of channel locks squeeze down and unscrew the motor pulley
13. Reattach the idler pulley
14. Pull the belt along the pulley wheel and then bring the belt around the motor shaft
15. Replace the front panel
16. Rescrew the 2 screws on the front panel you took out previously
17. Connect the wire harness
18. Place back the dryer lid
19. Rescrew the 2 screws you took out previously with your Philips head screwdriver
20. Place back your lint filter
21. Repair is complete
22. Connect your appliance to its power source
This part may also work with other Whirlpool manufactured brands including some Maytag, KitchenAid, Jenn-Air, Amana, magic Chef, Admiral, Norge, Roper, and others.
Visit www.pcappliancerepair.com/inde... to find the part that works for your Dryer!
Get more dryer repair help at www.pcappliancerepair.com/repa...
Make sure to connect with us!
/ pointclickap. .
/ pcapplrepair
plus.google.com/+pcappliancer...
/ pcapplrepair
/ pcappliancer. .
pcappliancerepair.wordpress.com/
Subscribe to our e-mail newsletter for more appliance repair help, new product news and more. Visit www.pcappliancerepair.com and enter your e-mail address in the subscribe box on the side.
Please give us a like, and subscribe to our channel!
If you have any questions, please feel free to leave a comment below!
Пікірлер: 29
Thank you so much for posting this video! You made an almost impossible mission for a women to make so easy! It worked like a charm! Thanks again!
Woo. You saved me wasting a lot of effort sir. Thanks for the video
I can't thank you enough for putting up this video. Much appreciated!!!
Thank you for this video. Very informative. I fixed my own dryer and probably saved hundreds.
Super helpful. Thank you for this video. Replaced the pulley with ease, thanks to you!
Thankyou, god sent you to teach us, i'm a diy mecanic, you helped me out
Very good. Part came today. Vice grips and channel locks used. Kenmore is working as we speak. Thanks
It helps me to replace my dryer pully , thanks
Thank you for the walk through it helped me alot.
best video for this job, thanks!
FYI shaft of the motor has flattened sides, I used a adjustable cresent wrench and vice grips to remove the old pulley. Whirlpool\Kenmoore 70-80 series.
Saved my dryer! Thanks!
Great video saved me a lot of money
Excellent video
Thank you very much!
How much do you tighten the motor pulley? Tell it can't go anymore?
exactly what i need to do and belt of course...thx
Thanks so much
It would be vastly helpful. If you would have committed upon the possibility of REVERSE THREAD, somewhere in this video! It turned a 45 minute job into 5 hours of endless frustration. Try removing a left handed nut using the right handed nut removal method. Having to put the motor in a vise and using a pipe wrench in an attempt to remove the pulley. I worked on it with cheater bars until it broke up and fell off. And as you might have guessed, when I started to thread the new pulley on, that's right, it wouldn't go. PLEASE,PLEASE,PLEASE, add an amendment to this video. Informing everyone of the real possibility that they my have a REVERSE THREAD PULLEY SHAFT! Submitted Respectfully, Marty
Could this pulley be why my belt keeps shredding? I just replaced the other pulley and wheels. Not sure which is causing the shredding
Mine says 27 but my belt is 29" does that matter?
Howdy need your help: I can’t find the motor pulley part I have a MAYTAG SDG3606AWW can you point me in the right direction? Thank you
I just replaced the motor pulley on my whirlpool because the old one broke and ripped the belt as well. The new one did the same thing within a couple of weeks. Does anyone have any idea as to why the threads are getting destroyed causing the belt to break as well???
My motor shaft is broken ! I’m guessing I have to change the entire motor huh ?
Okay but it's BROKEN. There is only the back curved part to take off but no way to grab onto it since it's CURVED and the part you grabbed broken off. How do you actually get it off?
@cbj6801
2 жыл бұрын
Vice grips
@owenmontgomery1197
2 жыл бұрын
Pipe wrench, also be careful, it might be reverse thread.
My new one won't thread on
@squarehouse5918
3 жыл бұрын
Your motor shaft is reverse-threaded, this pulley has standard thread..late reply😀