Very good. This shows what just proper gearing can do. I just got my first taste messing with these 1/12 scale 4wd rigs. Not bad once you learn what goes where.

Wow! This is unbelievably quick out of the box!🏎️💨⚡️⚡️⚡️

@customtoyrevolution

Жыл бұрын

I was surprised the ESC hold up

Really informative video, thanks. I'll keep mine with the stock setup until I get more experience with the car, but it's nice to know that so much more speed is available with only a change of gearing.

@customtoyrevolution

Жыл бұрын

Absolutely take your time

@michaelfear4801

Жыл бұрын

did yours finally come ??

@mikegreen2214

Жыл бұрын

@@michaelfear4801 Ha, nope - but at least it's on its way. I contacted them to change the order to the single-battery package they had in stock, otherwise it probably wouldn't have even shipped yet.

@mikegreen2214

Жыл бұрын

​@@michaelfear4801 It finally arrived and it's awesome. The delay meant that I had plenty of time to stock up on parts upgrades, extra tires and the new X6PM controller with a gyro receiver. I get mad wheelspin when I gas it on some of the local surfaces, so the gyro is sweet. Insanely good car for the money; I'm so impressed that I just ordered an extra one.

@michaelfear4801

Жыл бұрын

@@mikegreen2214 that's awesome dude! about time hahah extra shocktowers and tires are a must even if you don't bash it, the towers are very weak.

Good info bud. Great Vid.. You put up some nice numbers... 👍

@customtoyrevolution

Жыл бұрын

Thanks 👍

Nice upgrade 😁👌

I am thrilled with my MJX 16207, which is basically the same as this just a little bit shorter. However I do not even dare to wear flip flops or sandles when running it, that front metal bumper will be a world of hurt when it hits you on the toes or feet!

@customtoyrevolution

9 ай бұрын

Crocs took an impact surprisingly well, no pain at all, at least around 30mph, been there, LOL

Nice, good thinking!

@customtoyrevolution

Жыл бұрын

Thanks!

Nice video

Nice vid, but you gotta talk louder when running the car!

@customtoyrevolution

Жыл бұрын

I'll try. Thanks

@daig1984

Жыл бұрын

Can’t hear anything

@Sam-nz2zs

8 ай бұрын

Can’t hear you talking mate

I found that pin on the front after adding some lithium grease to the diff and had to start all over again, I was not happy😂😂 ours run fine on 3S 25C 3300mah lipos but be careful the battery doesnt slide forward onto the steering servo arm and stop your steering. we ended up using velcro to stop the battery sliding.

@customtoyrevolution

6 ай бұрын

velcro or a few drop of hot glue can act as the stop

Hello, your videos are excellent... I also have a 124008 and I have only used it 5 times, no jumps, no crashes and the rear Dogbone has been solid in place and has worn the cup, according to other comments from other owners the Dogbone is somewhat short and several have given that problem, that has happened to you ?... some solution in this regard... I'll thank you.

@customtoyrevolution

4 ай бұрын

Yes, I have the same problem where the rear drive cup got worn from accelerations. That's a common problem for ALL wltoys 1/14 to 1/12 buggies. No solution other than replacement. I tried MJX diffs but they don't fit.

@eduardomalcom2228

4 ай бұрын

@@customtoyrevolution Thank you... Someone told me that putting a few rounds in the differential cup could help, so that it doesn't wear out the mouth of the cup and get out of place.... What do you think about this?

@customtoyrevolution

4 ай бұрын

I can't think of anything that would help@@eduardomalcom2228

@eduardomalcom2228

4 ай бұрын

@@customtoyrevolution thanks

😊

How does your bevel gear on driveshaft use Allen key? That’s mad lol

@customtoyrevolution

8 ай бұрын

first time I see it is from mjx, wltoys just copy it. I was shocked too

So you have the bigger bearings on the bevel gears from the 124007/124017?

@customtoyrevolution

6 ай бұрын

Hopefully you get what I am saying by now

@Sam-nz2zs

6 ай бұрын

@@customtoyrevolutionthe only thing I want to know. Is did you use bigger bearings from the 124007 for the bevel gears ? As I see you got 2 bearings on each side onbevel gears and one on spur gear ⚙️

@Sam-nz2zs

6 ай бұрын

@@customtoyrevolutionso you have 3 bearing in total on driveshaft and all used from the 124008?? Or the two bevel gears are from 008 and the other one is 124007 with the spur gear?

How did you managed to take off the engine mount? I hate that they put loctite near a plastic 😢

@customtoyrevolution

9 ай бұрын

Just unscrew, they didn't put loctite on the one I purchased. For anyone needed to do localize heating of the screw, used a soldering iron.

What size bearing for both bevels gears and what size for the spur mate ? You got that in mm

@customtoyrevolution

6 ай бұрын

No measurements, sorry

I need to know how many bearings you got on your driveshaft? And not sure what you mean about 124017 124007 and 124008 bearings lol…..

@customtoyrevolution

6 ай бұрын

Don't worry about them

Is the driveshaft gear set you have linked does that have the “bigger” bearing mate?

@customtoyrevolution

8 ай бұрын

I believe I explained in the video

@Sam-nz2zs

8 ай бұрын

@@customtoyrevolution so all you change to driveshaft is putting a 44t spur on. And take the two bevel gear bearings off ?

@customtoyrevolution

8 ай бұрын

@@Sam-nz2zs you also need a new pinion, see description for size

@Sam-nz2zs

8 ай бұрын

@@customtoyrevolution thank you mate

Can I just chuck the whole 124017 driveshaft with spur gear and bearings into the 008? As a whole ?

@customtoyrevolution

8 ай бұрын

no, watch video again where I talk about the bearings. you will need tools to disassemble the center drive assembly

Is that the same motor pinion to MJX hyper go brother?

@customtoyrevolution

11 ай бұрын

No, Mod 0.6 15T Pinion (Wltoys) vs 14T Pinion (MJX)

that shock tower replacment can use from wltoys 124017?

@customtoyrevolution

11 ай бұрын

Yes but not direct replacement. You also need the shock spacers from 124017.

Is that big motor pinion fit with MJX hyper go?

@customtoyrevolution

Жыл бұрын

No, unless you custom made a motor mount

So I ordered the 124007 driveshaft and all that. But it didn’t come with bearings …

@customtoyrevolution

6 ай бұрын

Should have ordered from me, lol

It’s easier to just flip the motor mount & fit a 20t o.6 mod pinion that’s what iv done with mine .

@customtoyrevolution

7 ай бұрын

People do it with 20t, how do you manage a 22t?

@Rc-Mad-Ness

7 ай бұрын

@@customtoyrevolution ye sorry your right I used Schumacher 20t 0.6 mod pinion , that’s my fat fingers lol

@customtoyrevolution

7 ай бұрын

You should get 43mph and make sure to add a cooling fan

what is the name of this application that you use to see the speed of the cart?

@customtoyrevolution

10 ай бұрын

search for SkyRC on playstore. It's currently called "Power GNSS", old version is called "GNSS PA"

Can you tell me the tooth count and mod of your new pinion please? And possibly where you sourced it?

@customtoyrevolution

Жыл бұрын

In the description.

@tooleyzrc1973

11 ай бұрын

Thank God! That's what it looked like so that's what I ordered. This car is perfect cept for that metal spur and tiny pinion. Not sure why that chose to go that route. You'd be hard pressed to strip that plastic spur on its cousins if your mesh is good. One of the most enjoyable things about the 124017, 19 are the buttery smooth, QUIET drivetrain. Thanks for solving that for us!

@tooleyzrc1973

11 ай бұрын

I just did the mod! Thanks for fixing this cars issues. Ditched the unnecessary bearing as well. Haven't clocked it but I'm running her on 3s. Had to make some adjustments to the battery tray. Screwed a chunk of an 3s Arrma chassis to add a stop piece to keep the battery from hitting the steering arm that's connected to the servo horn. Sweet little car that can now hang with it's metal chassis brothers.

Have you ever increased the pinion of some mjx hyper go?

@customtoyrevolution

10 ай бұрын

no yet

@rush338

10 ай бұрын

@@customtoyrevolution I couldn't find any videos about it.

So you got one bearing on each bevel gear ? But not on spur?

@customtoyrevolution

6 ай бұрын

Tried it, doesn't hurt. It's to reduce friction

@Sam-nz2zs

6 ай бұрын

@@customtoyrevolution I see you only had one bearing on one side of the driveshaft bevel gear and one bearing on the spur gear. That’s it mate

Hi,was the stock oo8 gearing mod .6 or .7?

@customtoyrevolution

5 ай бұрын

0.6

what if I use a 4000mah 3s lipo batteries can it be safe and increase speed?

@Sam-nz2zs

4 ай бұрын

No just longer play time with higher mah.

@palemonvazquez1383

4 ай бұрын

@@Sam-nz2zs how long do you charge the battery for

@Sam-nz2zs

4 ай бұрын

@@palemonvazquez1383 o have 2200mah and 3s and charge it for 45mins. And use it within 15mins probably…

What sort of 2845/ kv?? If I use bigger motor?

@customtoyrevolution

8 ай бұрын

no set answer, depending on your goal

Did you use 124007 bearings ?

@customtoyrevolution

6 ай бұрын

You don't need bearings from 124007

@Sam-nz2zs

6 ай бұрын

@@customtoyrevolution so all you need is the bearings from the 124008? One bearing on both bevel gears and one bearing on the spur ?? That I can see

What size is the motor gear?

@customtoyrevolution

2 ай бұрын

See detail description

I didn’t see where you went 50mph? It said 55?

@Sam-nz2zs

8 ай бұрын

It said 45mph I mean

@customtoyrevolution

8 ай бұрын

50mph speed test at the very beginning at about 1min, the test towards the end is for acceleration which show 45mph /w 1.03g in 3.08 seconds. 55mph is on part3 with mjx tires