i had issues with randomly flashing control lights with my interceptor 650. cleaning the relays worked perfectly.

Great video. You provided the exact information I required to replace the relays in my Himalayan and I've got new relays ordered.

@iamalexsun

16 күн бұрын

@@Apollo949 thanks! Glad I could help!

I had this problem, the fuel pump wouldn’t prime, I cleaned the relays and it worked

@claytonluke81

4 ай бұрын

same

I will say this. As a new rider who never rode before MSF class when I bought this bike, I just thought it was my error making it stall on slow right turns. When I did this on day #2 it only stalled once, unlike the 6, the first day. It does make a difference.

Thanks for identifying a cheaper relay that works - Bosch, a German brand, is ALWAYS expensive, and Japanese electronics are usually good quality. As for the dielectric grease, just put a dab on a Q-tip and smear it over the surface of the contact, and that will block air and moisture from causing corrosion. The pressure of the mating contacts is enough to push through it for a good electrical connection

Congrats on the new bike. I’m enjoying your videos as you share your experience. The RE community is great. Knowledgeable and friendly.

Hey there, watched your video and took your tip on the GoPro mount screw! A little tip on that… the screw is very long and for me was pressing onto the wiring loom below. Vibration over time will cause the screw to cut its way into the loom and possibly short something out. I’ve cut the screw and made it shorter, it no longer touches the loom and also takes less turns to screw it 👌🏻 Check yours to be safe… 😊

@iamalexsun

2 ай бұрын

Thank you for the heads up! Will definitely check that asap!

I have not seen anyone showing you HOW to change the relays .... thanks for this vid..

This is one of the best videos I've seen on cleaning and replacing Enfield relays. Thank you!

@iamalexsun

Жыл бұрын

Thank you! I'm glad the video was helpful.

@antoniocorelli

3 ай бұрын

Yes. I agree

For my Himy I just bought a pack of 6 replacement relays from a reputable brand and changed them all, cleaning the plugs and adding dielectric grease. Done job. Not had a single electrical problem since.

@BashBunny-jr1jc

2 күн бұрын

Which brand and model number please thank you

I like the video. Helpful. Subscribed.

This video literally helped me get my bike running again. I have a service manual for every motorcycle I own EXCEPT my GT 650, thank you for pointing out which relay is which!! 😄👍🏼

@iamalexsun

Жыл бұрын

Thank you for taking the time to leave a comment. I’m glad the video helped! Ride Safe!

Alex. First part of my post Break-in service is done. Oil Change. Chose to go and do it myself. I am not a stranger to working on classic cars. So working on a retro motorcycle is something I can handle. Now I did have to order a few of tools but now that I have it all I can do the next service far cheaper. Price of service was another motivation as It would have cost around $500 for a Oil change and the Valve inspection/adjustment. You have already got to the service mark have you not. Thinking of doing the service your self? You already are adding after market parts and doing things like the relay cleaning.

Mine is stalling at junctions, brand new bike, 4 pin relays which is good but absolutely SLATHERED in grease 🙄 I will clean and try again. Genius idea with the gopro screw 🙌 Im gonna do that now 😁

@iamalexsun

Жыл бұрын

That’s such a bummer! Hopefully cleaning it helps. Please keep up updated! Ride Safe!

Fine advice . Subbed Alex , Ta .

Please make more videos, It's good. And go to some twisty roads, like mountains. That is the real where real fun starts. It's in the twisty roads and mountains, cold winds and adventure. Just don't lean too much on the corner because sometimes there is gravel that can make you lose grip. ( A friendly advice 😉) up hills and down is fun 😊.

Also clean the connectors in the headlight ie signals, brake light connections etc.

I had to do the exact same thing on my 650. Was stalling for no reason, sometimes not starting. Ordered new relays, cleaned out grease, used dielectric grease instead. Issue never reappeared.

Hi very useful video thanks

Hi , take a look to the length of the Gopro screw , if it is too long may touch the wiring underneath. Apologies for my english

Very helpful - especially about using the GoPro screw - anything with a 10mm metric thread should do, as it's a bit of a pain having to use an Allen key, always with the risk of losing the screw. Regarding the relays, I haven't had any problems yet with my four-year-old Interceptor, but I will take the opportunity of checking them for excess grease. I would have been inclined to use copper-ease grease, as it is conductive.

@josephcleek925

Жыл бұрын

Using a conductive grease on those relays will cause a short circuit. The dielectric grease is there for corrosion protection only.

Boss put a gopro hook onto the left panel... Real G

Hey guys, thanks for the nice video on the RE relay problem. I wouldn't expect such problems with a new machine... When I clean and lubricate the relays on my Classic 350 machine, do I have to disconnect the battery and contacts? Thank you for the information and I wish you a merry Christmas. Robert from the Czech Republic

@iamalexsun

Жыл бұрын

Thanks for stopping by! It is recommended to disconnect the battery while doing electrical work. Using the correct cleaner and tools also decrease the chance of something unfortunate from happening. That being said, if you don’t want to go though the hassle of disconnecting the battery and the wiring, just be really careful not to overspray the cleaner on other parts. Please keep us updated! Happy holidays to you as well. Ride safe!

Worked on a number of indian lambrettas years ago. Poor copper in the wiring, looms, switches etc. Caused continuous problems and it seems this might be an ongouing outsourcing problem.

thinking of doing the same

3:19 if someone with an Apple phone steals the bike, they will be told they have an apple tag near them.

@iamalexsun

Жыл бұрын

They’ll have a great time trying to find it

What's with the black tape on the side panel?

Hey Alex, great video explaining the relays and giving step by step on cleaning them. I’m having same issue sometimes my INT650 won’t start sometimes, so I decided to clean them and reinstall. Is it okay to reinstall same relays or do I have to get new ones? Thanks!

@iamalexsun

Жыл бұрын

Thanks for watching, I’m glad the video helped! There is no need to get new relays after cleaning and/or if the factory ones aren’t broken. However, you should always carry a spare relay or two just in case.

@Yashp097

Жыл бұрын

Thanks for your feedback!

Thanks a lot for this and your other videos 🙂 Is there a reason you put grease on only 4 instead of 5 pins? Funny thing, in Germany a Bosch relais is 3$ and Panasonic is 10$

@iamalexsun

3 ай бұрын

Thanks for the comment! I’m glad my videos have been helpful! The relays only have 4 pins, the empty one you see in the socket is not used for anything.

Hi like your videos...what's your occupation

Hi Alex, Thanks for this video. Its marvellous. I have a serious problem with my 2019 RE Cont 650 and it is that the engine cuts off once the Abs comes on and then the engine failure warning light comes on. I manage to start but after a few kilometers it stops again. One of the times I almost fell. I no longer have confidence in the bike. Do you think that making the process that you explain about relay will solve?? Thanks again

@iamalexsun

6 ай бұрын

Thank you for the comment and taking the time to share your situation. That sounds very scary and you are absolutely right to be concerned. I am not a motorcycle mechanic so I would not know the best course of action. However, I would definitely try cleaning the relays, and replace them if you feel necessary. If the issue persists, it would be in your best interest to take it to a professional and having them diagnose your bike. Hope this helps! Ride Safe!

@clivemant894

6 ай бұрын

1:23 I had a similar issue with my 2019 interceptor after a year, it's only done 2000 miles now but the issues started with occasional cut out. Fiddle relays and it went again so I cleaned and fitted Bosch relays, thought it might be ignition switch but all checked out OK. Laid up over winter, fir a while I turned ignition on weekly to check ok. Then out of the blue, turned it on. Nothing! So carefully removed seat and side panel to attempt to find issue, turned my back and as I'd left ignition in on position, all of a sudden all came back to life! Studying visually, saw a wisp of smoke from area under battery, turned out the red wire from starter solenoid to fuse box has a joint located above swing arm, to access its wheel out and mudguard removal, the spade connectors were blue with corrosion and had been heating up melting the boot over, it's in a lousy position and wonder if it was assembled incorrectly, now soldered to new spades and waterproofed.

🌹🌹🌹

I have to ask, because I am (very) rusty on my electrical knowledge, how do you determine the proper spec to make sure you have the right replacement relay?

@iamalexsun

Жыл бұрын

I did my research on reddit and various forums, the two products shown in the video were mentioned the most and the feedback was also the best. Perhaps someone more qualified could chime in and share their knowledge on this.

@avgjoerides

Жыл бұрын

@@iamalexsun No worries. I came to the same conclusion as you did between the Bosch and Panasonic but my curiosity gets the best of me sometimes and go down these rabbit holes so to speak. Thanks for the response and sharing your experience thus far.

My console abs indicator keeps flickering.. Abs works fine light goes off when I ride.. But Starter unlike other indications abs light flickers.. Will cleaning relays will solve it.?

@iamalexsun

10 ай бұрын

Thanks for sharing. I have not encountered or seen this issue personally. I would try cleaning the relays. If that doesn’t work, please reference the service manual here. drive.google.com/file/d/1EPfodqvw-ZL_bvy6LIzhlByW8KlNFlNe/view

why you changed original relays as after cleaning orignal one was working fine?

@iamalexsun

Жыл бұрын

No particular reason at all. I just wanted new relays.

Sup mate. I also got an in650 as my first bike. Though I'm not through the break-in period yet so I avoid revving 5000+ rpm which is what you need to get to freeway speeds. Although I did hit the freeway once, my front wheel gets very wobbly on very high speed curves. Was wondering if you're having the same issue. Word is that it's the front tire that's the problem. Also, what was the mileage before you replaced the relay??

@SB-or5mj

Жыл бұрын

Could be a few things. None of them major, all little adjustments. One, an out of balance front wheel, which I doubt because the wheel weights are installed at the factory and in general are pretty universally placed and correct. two, the front fork steering stem bolt. The big silver 8mm hex under the center of your handlebar. It adjusts how easily the handlebars turn. they should turn very easily, but not wiggly loose. From the factory they're typically too loose. Loosen the 4 fork pinch bolts in the top triple tree. then snug down the large 8mm hex just a bit. then re-tighten the pinh bolts. You can find torque specs online for the pinch bolts. That typically solves the wobble issue. Mine never had it, but I went around their entire bike and snugged up all the bolts when I got it. It's not an uncommon issue htough.

@gotpkrgotpkr

3 ай бұрын

​@@SB-or5mjheh there, i have a question please. Do i have to lift the front wheel to adjust the front fork steam bolt or is it ok not to ? Thanks in advance

How's the relays are going on?

@iamalexsun

Күн бұрын

@@BashBunny-jr1jc relays are good. no problems whatsoever.

@BashBunny-jr1jc

Күн бұрын

@@iamalexsun I was planning to buy Bosch relays but this panasonic are costs almost half in price so that's why I asked about those panasonic relays, Thanks for replying

@iamalexsun

Күн бұрын

@@BashBunny-jr1jc no problem! I would go with the Panasonic ones, they are just as good as Bosch!

@BashBunny-jr1jc

Күн бұрын

@@iamalexsun 🙏

There is nothing wrong with stock relays. Just clean the connectors....

@iamalexsun

9 ай бұрын

Absolutely, there was no need to replace the OEM relays. I did it just because I could.

U need aftermarket exhaust bro

Once you cleaned them out there was no need to replace them.

Dielectric grease does not inhibit electrical continuity. Bad advise do not do!

Great video. Suscribed

@iamalexsun

3 ай бұрын

Thank you for the support!

🇩🇴🇩🇴🇩🇴Best regards brother from Dominican Republic excellent program I have a new Royal enfield interceptor 650 mark2

@iamalexsun

Жыл бұрын

Thank you! Ride Safe!

@daniellantigua7659

Жыл бұрын

@@iamalexsun I am your new subscriber and I follow you