✨ Whirlpool Front Load Washer F03 E01 ERROR - Easy DIY FIX ✨
✨ Whirlpool Front Load Washer F03 E01 ERROR - Easy DIY FIX ✨
Very easy Fix. Just unplug it for 5 minutes and then plug back in. Video Also covers how to clear a plugged pressure sensor tube that can cause that Error.
This error is also often caused by using too much detergent which creates too many soap suds and creates this error.
QUICK AND EASY APPLIANCE DIY REPAIR VIDEOS - SAVE BIG $$$ BY FIXING IT YOURSELF✅
✨ If the video was helpful, remember to give it a Thumbs Up 👍 and consider Subscribing. New videos every Saturday ✨
-Subscribe Here: / @scottthefixitguychannel
🛠- Do You Need Any Additional Help? Become A Member of Our Channel Today and Get LIVE HELP from Scott With Your Appliance Repair. Pick #1 FIX-IT FAN for Just $4.99 and get Text, Zoom, Email or FaceTime Live Help. Non-Members pay $45.00 for Live Help. Just $4.99 for Channel Members. Click Here to Join Today: / @scottthefixitguychannel
-Facebook: / scottthefixitguy
-Twitter: / scottthefixitgy
-Instagram: / scottthefixitguy
-KZread Channel: / scottthefixitguychannel
-If My Advice Has Helped You…
Please Click Here To Donate: www.paypal.com...
Donate with Venmo - Click Here:venmo/u/Scott-Flint-1
-GREAT PLACE TO ORDER O.E.M. Genuine Parts for Your Appliance - Click Here: fix.pxf.io/MmrxYY
-Need Expert Appliance Repair Help Today? Click Here:asqme.com/@sco...
-Good Place to Buy Parts: bit.ly/3wD4L5W
-List of Tools used by Scottthefixitguy: • ✨ Scott The Fix-It Guy...
-Need More Expert Help with Your Repair? Click Here To Schedule a 15 Minute Meeting with Me Using Zoom 💻 : calendly.com/s...
Disclaimer:
Because factors beyond the control of Scottthefixitguy, I cannot guarantee against improper use or unauthorized modifications of this information. Scottthefixitguy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Scottthefixitguy recommends safe practices when working on appliances and vehicles and or with tools seen or implied in this video. Due to factors beyond the control of Scottthefixitguy, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Scottthefixitguy.
Thank you 😊
Scott The Fix-It Guy *
*
🐔 Check Out Our New Channel Dedicated To Showing How To Raise Your Own Backyard Chickens: / @raisingbackyardchickens ***
***
Scott The Fix-It Guy - Appliance Repair Videos Do you need More Appliance Repair Direct Help from Me? Visit me at:AsqMe.com@ScottTheFixItGu and I'll help you get your appliance working again quickly.
Пікірлер: 83
I would try this, unplugging it for ten minutes and plug it back in and if that does not work try this next step. Unplug it and wait for ten minutes the pour about a cup of warm water in the soap dispenser, you should be able to see it running down inside the washer. Plug it back in, that's it. If you are still getting an error or the door will not unlock by itself you may have to unlock it manually as seen in the video, you might as well take the cloths out once you get it unlocked. Also just unplug it while you going through the process to unlock it manually and save yourself ten minutes. Here's a couple tips to help avoid this problem in the future. 1. make sure to use HE detergent AND use the recommended amount, adding more is not going to get your clothes cleaner. Use the measuring cup provided, using that push bulb to put in laundry detergent is not a good habit. 2. The laundry detergent should be the last thing you do, if you put it in first it will just run down inside the washer and it will not mix with the water, it will also drain into the drain pump which cannot pump out the heavy undiluted soap thus causing an error. Remember the washer pumps water into the soap dispenser so it's mixes and is not so dense, if you put the soap in first by the time you get your clothes in it's already drained inside your washer and into the pump.
@ScottTheFixItGuyChannel
Ай бұрын
Thanks Gerald, Excellent information 😊
Thank you Sir. This was simple and worked because I had replaced the pressure switch (2x) and the water pump. Neither fixed my E03/F01 but I finally found your video and simply blowing in the hose connected to my pressure switch cleared. There was a little blockage not much but we are back in business and have been through 5+ loads with out erroring out thanks again for just your quick explanation of the part helped me understand.
@ScottTheFixItGuyChannel
9 ай бұрын
That is Excellent News, Thank you 😊
@michaelvillalona1215
3 ай бұрын
Thank you for posting this! I followed your exact steps and it worked for me! THANK YOU!
I just had to come on here and say THANK YOU! I followed each step and fixed my washer on my own today, saving who knows how much money!! Thank you again !
@ScottTheFixItGuyChannel
2 жыл бұрын
I’m proud of you Amy❤️😊👍
@pavelkomar6965
2 жыл бұрын
You saved 420$
Like others, I tried this trick but no luck. But then after resetting, I opened the door to feel the clothes. Opening the door *after* unplugging/re-plugging power made the error codes disappear and the machine work again. Worth a shot before pulling out the tools
@ScottTheFixItGuyChannel
2 жыл бұрын
Nice job Blannie, Thank you😊❤️👍
Power cycling didn't work for me, but blowing through the hose and resetting it did. Thanks!
You are awesome! I got it to work… hopefully it’s a full cycle. Thanks so much 🙏🏻
I checked the trap, nothing. I replaced the pump, same problem. I replaced the air valve, same problem. I replaced the check valve, same problem. My wife then got the bright idea to change the spin cycle Medium on every wash load. So far, it has been 6 months without a problem. I think sometimes the spin cycle doesn't let the water drain causing the problem. Change the spin rate to medium or slow and see if it helps!
@ScottTheFixItGuyChannel
2 жыл бұрын
Great idea Tom, Thank you
@daynahall9639
Жыл бұрын
I’ve been going crazy trying to do the same thing w my front loader duet. I’m going to try this !! Mine won’t drain it keeps throwing F9 E1 codes and we’ve tried everything . No water in tub but there’s a drip in the door seal. Don’t know if it’s related . I’ll try the M spin speed
@photobuf1
Жыл бұрын
@@daynahall9639 Good Luck! Mine is still working after more than a year.
Thanks so far so good running some test washes. FYI I did have to take off the top as well to pull the tab to release the door lock and also I cleaned the filter trap.
@ScottTheFixItGuyChannel
2 жыл бұрын
Awesome, Also try cutting your detergent amount in half👍
@msstallionaire
5 ай бұрын
Oh, no, the door it’s not locked
Mine was the drain motor. If you’re underneath cleaning the coin trap-touch the motor to see if it’s hot. Mine was very hot and struggled to run.
@ScottTheFixItGuyChannel
Ай бұрын
Good advice👍
We’ve had our whirlpool duet for 8yrs, never had an issue with it. That’s because I used to water down the liquid detergent. Then I got lazy and just started using it full strength and for the last few months I’ve been getting these error codes on and off. I finally came to the realization that I need to take the time to water my detergent again. 50/50 detergent/water. That should do the trick.
@ScottTheFixItGuyChannel
Жыл бұрын
You are soooo right. Just using 1/2 the detergent does the trick👍😊
thanks dude!!!!!!!!!!!
Hi Scott ,I have a similar machine, never used , first time plugged in , no power , no display
@ScottTheFixItGuyChannel
2 жыл бұрын
Can you send that same question to my email? At: scottthefixitguy@yahoo.com
thank U so much HELP ME!!!!!!
@ScottTheFixItGuyChannel
2 жыл бұрын
You’re very welcome👍
Perfect! Just what we needed help with! Thank you so much, much appreciated!
@ScottTheFixItGuyChannel
Жыл бұрын
You’re very welcome 😊
@sonjaboon3280
Жыл бұрын
@@ScottTheFixItGuyChannel you saved us money!!!!
I have to replace my water inlet valve for it to work after trying to replace water sensor and the air tube. My cold 1 valve have a problem so water doesnt come out enough thats why the water sensor keep sending error code f03 e01
@ScottTheFixItGuyChannel
2 жыл бұрын
The new valve should do the trick👍
@dwaynedunkerson2425
Жыл бұрын
Exact same thing here too Hanh. Thanks for the information. Replaced my inlet valve and back in business.
Recommend to check the water inlet valve also. It might be the issue too. My experience.
@ScottTheFixItGuyChannel
2 жыл бұрын
Thanks Mark👍
@florinake85
Жыл бұрын
life saver!
Awesome content thanks for your help
How do you differentiate from it being the water inlet valve and something else. I keep getting the same code and have tried the above video with no success. I don’t want to buy the part if I know it won’t fix the issue. The current water inlet valve is also not leaking.
@ScottTheFixItGuyChannel
2 жыл бұрын
Here’s a good article on things to try: flamingoappliance.com/washer-repair/how-to-fix-whirlpool-washer-f3-e1-error-codes/
So I've tried unplugging multiple times, even cleaned out the filter. Every time I plug it in it's the immediate codes and sounds like it's trying to drain but won't stop until I unplug it again . Any ideas???
@MrPilcountry
2 жыл бұрын
Did you get yours fixed? Mine is doing what you said yours was doing.
@annakajner
2 жыл бұрын
Mine doing same. What do I do????😢. Please n thanks!!
@kevin_11_07
2 жыл бұрын
@@annakajner mine ended up being the water inlet valve.
@kevin_11_07
2 жыл бұрын
@MrPilcountry mine ended up being the water inlet valve. Replaced it and works great now
@annakajner
2 жыл бұрын
It was actually the lock in the end. I continued to read the comments. I fixed it!
Good day Sir,I'm having a problem with my washer. I'm able to turn on the machine but I'm getting to lines like this ‐ ‐ and the machine won't start. Please respond ,thank you.
@ScottTheFixItGuyChannel
Жыл бұрын
Hi Basil, Can you try unplugging it for half an hour and plug it back in to see if that helps? Here’s a video that shows also how to do the diagnostic test: ✨ DUET WASHING MACHINE - EASY DIAGNOSTIC TESTING ✨ kzread.info/dash/bejne/faSsyqSGd7rNeZc.html
My washer is with those codes but door its close. I unplugged but still doing the same thing.
solved? looks like you applied a tiny patch
@ScottTheFixItGuyChannel
Жыл бұрын
That’s right. Can help you do laundry while you wait for your new door boot👍
Thank you great info and it worked ... don’t know if the pump is strong enough to get the water up and out the elbow ... any thoughts ?
@ScottTheFixItGuyChannel
3 жыл бұрын
The pump might be partially blocked.
If that doesn’t work check the dome where the black tube goes into the tub they get clogged
@ScottTheFixItGuyChannel
2 жыл бұрын
Thanks Tony, Good idea😊
We have those codes showing, but the door is still remains locked. We drained what little water was in the tub but the door is still will not open and the codes are still throwing.
@ScottTheFixItGuyChannel
Жыл бұрын
Can you send that same question to my email at: scottthefixitguy@yahoo.com
@chadguidry8767
Жыл бұрын
Leave it unplugged for a few minutes, it should reset itself
@chandalarranch
Жыл бұрын
You can manually unlock it from the top. Remove top. There’s a round tab on the topside of the door lock. Pull up on it to unlock.
Wish this one worked for me. Door is locked and drain pump stays on with the error code E01 and F03 rotating on the screen. Unplugging the machine keeps the drain pump from burning out but if I left it plugged it the drain pump would stay on and the door locked. Tried unplugging and plugging in multiple times.
@ScottTheFixItGuyChannel
3 жыл бұрын
Can you take the screws off of the back of the top panel and remove the panel and then reaching behind the door lock and lift up on the plastic tab to release the lock that will also reset the washing machine so it will work properly.
@DianneGerrity
3 жыл бұрын
@@ScottTheFixItGuyChannel Thank you for the reply. We went through a few more videos and found that solution. Another one recommended cleaning the trap/filter. So we have done both, cleaned the filter and lifted up on that plastic tab to open and the machine is working. Whew! Had clothes I need for an upcoming trip in there!
@ScottTheFixItGuyChannel
3 жыл бұрын
Nice job Dianne😊👍😊👍
@bijkay0
2 жыл бұрын
@@DianneGerrity i have the same problem, and i did both steps too, but still getting the error code. I cleaned the filter and reset by unplugging the power, but the error code keep coming back and the door is locked
@manueldsalinas2147
2 жыл бұрын
@@ScottTheFixItGuyChannel this was my issue too. Fixed it. Thank you.
What does U4 means?
Replaced the water pressure switch, checked and cleaned the drain pump. Nothing helps. Any ideas?
@fringeminority5676
3 жыл бұрын
Remove the pressure tube from top and bottom put your finger over the end and blow through the tube. The tube may have a hole/wear spot. If so replace the tube
Mine brings in too much water in the drum
@ScottTheFixItGuyChannel
2 жыл бұрын
I think the water level pressure tube came off of the tub.
Just showing me how to unplug and replug the machine is not particularly helpful....
@ScottTheFixItGuyChannel
2 жыл бұрын
Hi Stacey, Give it a 30 minute unplug and it should reset. If not contact me at: scottthefixitguy@yahoo.com
@daynahall9639
Жыл бұрын
Scott - you’re a really good guy to help all these people . Thank you for the videos
@ScottTheFixItGuyChannel
Жыл бұрын
Thanks Dayna❤️😊👍