Very informative sir !!!! Haven't seen any video on KZread regarding this topic... Keep making such Informative videos on topics which are not yet explored... Appreciate your work always ....all the best for 1000 sub mark!!!!😄😄😄

@Yamakaze

5 жыл бұрын

Rajas Gadkari man I really appreciate you stopping by, remember you are the sole reason I am here, if only I could match your video quality 😂

@sukhmanderexperiment7727

5 жыл бұрын

Rajdoot ke full eingen work vedio bnana

@Yamakaze

5 жыл бұрын

VINTAGE MECHANIC rajdoot 350?

@sukhmanderexperiment7727

5 жыл бұрын

Rajdoot 175 cc

@Yamakaze

5 жыл бұрын

VINTAGE MECHANIC I don’t have one

Superb video dude,too the point.Just what i was searching for my rx

@Yamakaze

4 жыл бұрын

Slimline Customs 👍

Very well said, can you make a video to identify original piston vs duplicate piston. I brought a 1mm Goetze piston for Rx100 but it looks cheap and doesn’t have “goetze” print inside the piston whereas my old Goetze 1mm piston does have it

@Yamakaze

8 ай бұрын

Sure

Very detailed description..... Good 👍

@Yamakaze

Жыл бұрын

👍

Thank you so much, Sir!!!

Bro when we do a rebore does polishing the whole piston and the cylinder bore make any perfomance

@Yamakaze

4 жыл бұрын

Nope

Can you help...my RxZ producing ring bell sound ..the experts said that the piston should change ....what is the Hiden info on that sound ..can you tell the whole rate for repairing it ...what should do for that....

@Yamakaze

4 жыл бұрын

check the compression and if its low then take the piston out to look if there is excessive scoring. Price depends on your mechanic, the sound could be bearings, clutch bell or even the crank.

Very informative vedio bro ...keep going...save tow stroke 😎🤩🤩

@Yamakaze

4 жыл бұрын

arun kannan glad you found it informative

very clear thanks for the info

@Yamakaze

Жыл бұрын

👍

Hai. Could you please tell me which other piston suits Suzuki Shaolin to get more power. Or would it be ok to bore the existing one

@Yamakaze

4 жыл бұрын

There is no piston that increase power, what do you mean by boring the existing one?

@joshymathew876

4 жыл бұрын

Hai, too much white smoke coming. Either I have to re bore or to buy a new one. If I have to buy a new one, which one should I buy in case if I don’t find Shaolin piston. Any other models piston suits? Thanks

@Yamakaze

4 жыл бұрын

@@joshymathew876 white smoke in a 2stroke is not because of bad rings, that's 4 stroke, if the gear oil leaks into the combustion chamber this can happen.

Hai bro my Rxz Previous owner has bored it to 0.25 oversize and has used the std stock piston since it was in good condition now I am not getting the compression or the power generation, can I use a 0.25 oversize now without reboring it to 0.50? Pls reply me bro and mechanic checked and told the bore is in excellent condition on 0.25 oversize without any damages or scratches inside.

@Yamakaze

3 жыл бұрын

Put a .25 piston without rings and check, it should be slightly tight, if that’s the case you can install the .25 piston. You should never install a standard piston in a .25 bore

Some noise , something like by some loosen parts, comes out from the piston portion of my 93 modl rx100, for about 3 years. I did not open the head. Is that due to a damaged piston ring or so ?. I do not feel any power problem, but the bike does not give the crystal RX rin.tin.tin sound. Do I need to go for a ring change ?

@Yamakaze

5 жыл бұрын

Army Josh might be a bad top end bearing, it won’t be wise to just change the top end bearing, you need to change the other bearings as well, I am pretty sure that your crank will have play. You are looking at a overall engine rebuild.

@Yamakaze

5 жыл бұрын

Army Josh the top end bearing is a few 100 rs, change it if that’s bad. It’s worth a try at least

@splatharackal1337

5 жыл бұрын

@@Yamakaze OK..will go for it.

My bike rx135....starts without choke..power is also good...but piston is making knocking sound due to usage without 2T oil in d past....should I go for oversize rings or boring ???

@Yamakaze

2 жыл бұрын

Replied

Brother please do a video about all the RX models, 5 speed conversions, different models, how to find which model is which year from the serial number. And mainly what to look when buying a used one. I know I am demanding a lot, but I can't find reliable information anywhere else.

@Yamakaze

5 жыл бұрын

Let me try, i don't think one video will be able to do justice to this lengthy topic you asked me to cover. Thanks for subscribing

@fzlsalim

5 жыл бұрын

@@Yamakaze Your content is top notch, Thank you! A what to look for while buying a RX 135 would be really appreciated, because I am planning to pick up one.

@Yamakaze

5 жыл бұрын

Faizu Salim don’t worry, there are tons of content available, it’s just discrete. you can reach out to me for any questions through the Facebook fan page or instagram, details are on the home page of this channel

I own a shogun i wanted to know whether i should install sleeve in my bike or no its is cutrently running on 1mm piston. Will the sleeve decrease my power or are these just rumours??

@Yamakaze

Жыл бұрын

Sleeve will decrease the power

Very unique info. on the piston-rings-cylinder diagnostics. 👌 My Rx135 is in storage in outdoors for the past 5 years. Now, I have been able to get hands on taking stock of the condition and revamping slowly. As expected the engine is in seizure. I removed the head to see the condition, and to my surprise, I see some kind of scaling and deposits on the cylinder wall, giving it a scotchbrite kind of surface. It has hardened. I could see this as the piston has settled at the BDC. I am concerned and trying to understand about this condition of the cylinder. As kerosene is not available, is it a good idea to pour some 2T oil or diesel into the cylinder and leave it for some days? I had sprayed WD-40 two days back via. the spark plug hole to see if it can loosen. Only then, I have removed the head. I have dipped the cyl. head in diesel for general cleaning and hoping to dislodge the carbon in combustion chamber of the head. The bike is 22 years old but run less than 20k. Request your guidance for saving the cylinder. Thanks

@Yamakaze

21 күн бұрын

Use a a wire brush for cleaning the head

@vintubeable

21 күн бұрын

@@Yamakaze Thanks for the reply. Head is no problem. It got cleaned with WD-40 and diesel and some light brushing. The problem is with the cylinder wall where some crystal kind of deposits have accumulated. I see a direct contrast.... the cylinder wall is supposed to be the smoothest surface, where as right now it appears like the roughest sandpaper is stuck on the cylinder wall. 😊 I have been spraying WD-40 on the cylinder wall and then soaking a cloth in diesel and forcing it in the cylinder, so that diesel keeps dripping on the scaled surface. I shall observe and keep pouring diesel every alternate day for next 1 week and see the changes. Any better method you suggest could help save the cylinder. Thank you very much.

@Yamakaze

20 күн бұрын

@@vintubeable it’s the rings which are stuck, if the sand paper like surface is present then it’s better to break re it to next size

@vintubeable

20 күн бұрын

@@Yamakaze Quite possible. I shall know once it frees up from the seizure.I am working towards it. Thanks for the guidance.

Very helpful

@Yamakaze

4 жыл бұрын

Glad to hear that

I own a suzuki samurai. It is clocked around 80k kms. And havent done rebore till now. It is in std size. And bike doesnt idle well. It over accelerates when I start the engine. And stalls soon as I ride and stop.bad mileage. It is giving me around 10-18kmpl. And also it is not a constant mileage. Previously like last year it was in same condition but some what better, during those days it gave me around 40 kmpl. Exhaust was in good condition in those days. now there is not catalytic converter in it. Each and every time oil is dripping on the floor which is in pure black and thick in state. when i ride or else when i accelerate it hard it drips oil like hell on too the floor. Too much oil in exhaust. This is my bike's condition. Please help me. Can it be solved by replacing piston. Or else does it need a rebore. Please help.

@Yamakaze

4 жыл бұрын

Sai Yasaswi the revving is not piston related, you either have a vacuum leak or your throttle cable is stuck

How to check if the cylinder is bored properly??? How much gap should be there between two end's of rings after rebore if we insert ring without piston??

@Yamakaze

3 жыл бұрын

That’s not how you calculate the clearance. You will have to measure with the rings on the pistons. The factory recommended clearance for Yamaha and Suzuki bikes is 30 microns

4:30 Brother, I was told that the rings should not move freely in 2 stroke pistons and if it is 4 strokes, it doesn't matter whether they move freely or not.

@Yamakaze

Жыл бұрын

Not clear on your question

@mjshaheed

Жыл бұрын

@@Yamakaze At 4:30 mark, you were saying that the piston rings should move freely around the piston. I saw few other videos where they were saying that, in 2 stroke bikes, the piston rings should not move around freely in the groove and the piston-pin notch is there to prevent that from happening.

@Yamakaze

Жыл бұрын

@@mjshaheed that’s true. It won’t move freely. Maybe a mistake

@Yamakaze

Жыл бұрын

@@mjshaheed now I remember what I meant, it will spread out and form a tight seal around the piston and helps keeping the charge sealed in the combustion chamber. It won’t move around but it will spread out

@mjshaheed

Жыл бұрын

@@Yamakaze Thank you so much for taking time to explain it ❤️

Really very helpful video I have got on KZread after long time, Good job 👌👍. I'm having yamaha rx 100, but the problem is I need to give choke for starting the bike every time and even I have noticed Extra white smoke is coming out of the bike. I have done the complete engine work before the lockdown (engine rebore, changed piston, changed the bearing). Could you please help me out? I'm assuming the fraud mechanic just fooled me. JFYI I'm have maintained the speed 40 km per hr for riding purpose. White smoke which I have noticed. In 200 ml of petrol without 2t oil & the oil pump isn't working.

@Yamakaze

4 жыл бұрын

if a bike doesn't start on a warm engine without choke the pilot circuit is blocked, clean the carburettor and also make sure there is no rust in the petrol tank, replace the fuel filter after rinsing the tank if rust is there.

@amanmahajan9234

4 жыл бұрын

@@Yamakaze thanks for the reply really appreciated. Bike gets start in the warm engine and petrol tank is little bit rusty. Could you please help me out with the white smoke problem?

@Yamakaze

4 жыл бұрын

@@amanmahajan9234 White some means that you are burning the gear oil, white smoke is not to be confused with the blueish smoke that is a two stroke signature, some 2T oils produce more white than blue smoke. first thing to do is check the quantity of the 2T oil, max amount of oil should be around 30ml per litre of petrol. if that doesn't solve your problem than you need to see if real oil is shaping through into the combustion chamber. that would mean bad oil seals or worst, damaged crank case.

@amanmahajan9234

4 жыл бұрын

@@Yamakaze Thank you very very much ♥️

My piston is making noise...should I check d piston condition n then decide to go for oversize piston rings ???

@Yamakaze

2 жыл бұрын

Yes

Very useful...

@Yamakaze

4 жыл бұрын

Glad to hear that

One more thing , when should i need to replace the carb And what is good Changing carb or replacement of jets and all kit..?

@Yamakaze

20 күн бұрын

The carb is never really a consumable item, there are rebuild kits available that can take it to prime condition

Sir I want some information regarding Shogun sir so please , So how can I get help from u......

@Yamakaze

5 жыл бұрын

The facebook fan page and Instagram details are there on the homepage, please use them to connect with me

Bro..my piston is producing a lots of sound..so i decided to rebore my cylinder and add a oversize piston..at currently my piston size is .75mm and iam reboring it to 1.00mm..so will it decrease my mileage to a large variation..my bike is yamaha rx 100

@Yamakaze

4 жыл бұрын

It won’t cause a big impact but do the run in period perfectly

@ramalkhader3731

4 жыл бұрын

@@Yamakaze thank you

@Yamakaze

4 жыл бұрын

👍

Wich brand piston r gud?

@Yamakaze

4 жыл бұрын

Art

Will i have to ride below 40 to 50 kmph if i change piston rings?

@Yamakaze

2 жыл бұрын

For 1500kms

@Shriram_767

2 жыл бұрын

@@Yamakaze i didn't change piston i just changed piston rings.

@Yamakaze

2 жыл бұрын

@@Shriram_767 200-300kms

Bro eingen jerking rx135 While slowing the speed Pat pat issue Not smoothly throttling down Please give me solution

@Yamakaze

20 күн бұрын

Could be electrical, which year and model?

@baljeetsandhu2049

20 күн бұрын

@@Yamakaze 1999 rx135 bro Unsleeved .5 running Changed cdi swiss to Nippon Changed spark plug 2 times tried bosch and ngk But still same issue Also changed Reed valve HTA Bike acceleration up is smooth

@baljeetsandhu2049

20 күн бұрын

@@Yamakaze also i have changed the pickup coil brother

@Yamakaze

17 күн бұрын

@@baljeetsandhu2049 if possible try swapping the carb with a bike that is working well

How come we know that we reached the time of a rebore other than piston or rings sound? Is milage drop be a reason of rebore

@Yamakaze

3 жыл бұрын

Piston slap, loss of compression, mileage drop

Sir I installed new piston connecting rod and also piston bearing, connecting rod pin and it's bearing but after I start bike rx 100 I hear a Noisy sound,I think piston sound,so brother how to do please help 😥

@Yamakaze

2 жыл бұрын

Take it up a mechanic and find the source of the sound

Ee video Malayalthil ivduvo

@Yamakaze

5 ай бұрын

Illa

Malayalam video cheyamo

@Yamakaze

3 жыл бұрын

Ok

Hindi ma 🙏

@Yamakaze

4 жыл бұрын

Hindi channel hai, sirf 12 subscribers hai, subscribers bade toh videos dalun