Part Number RT32019 1.5" overall width Anodized Black

@anthony2558

3 жыл бұрын

At 1.50" was there any of the original stud sticking out?

I put 2" Orion spacers on my JKU. They make it look awesome on 35"s stock wheels. Nice video!

Great video! I also like the decal on the hood. You have me thinking of doing something similar on mine up here in Canada.

Really nice spacers. Thanks

I have a bronco, but your made me fall in love with the Gladiator.

Love the AMC Jeep hat!

Really makes it look like it should!!

Helpful. Thank you

Nice video. You have done great work with your Jeep. Really like the info on differentials. Will 1.25 spacers work on the Gladiator with stock Jeep wheels,

Nice hat buddy

Thanks for the video, nice job. I recently had spacers installed on my Jeep Sport S JLU when I had. 2.5 in lift put on with wider tires. Have you had any issues with the spacers? Thanks!

Thanks for the video. Looking at 1.5” spacers for my Commander with the 6” backspacing Commander wheels. I want to fit 265/70/17 on it.

@bigt5699

Жыл бұрын

Hey I got a commander also 09 just had rough country 2" lift installed r.c. recommends 265/70r/17 tires some posts said they rubbed a little. I'm wondering did you get the tires and the 1.5 spacers and if so any issues ?

I love it man! I have a question, where did you get those custom stickers in the rear of your jeep? I’ve been looking for a place to have those made. Thanks man!

Hey buddy. I love all your videos there are very helpful. I have a question: I have a JT on 37s planing on going 38 soon with 2.5” Mopar lift and after market wheels with a backspacing 4.75 inches and I would like to install the same wheel spacer you did to get a little more poke out. Would that be ok? Tires already stick out about 1 to 2 inches out just wanted a more wide stance. I don’t off road crazy, light wheel on snow or dirt but minor. I appreciate your help !

@lifeoutdoors3953

2 жыл бұрын

Are you a Honda civic stance boi? That’s such an ugly look

nice!

Well done but I have a question I planned to install spacers 30 mm on my JKU 265/65/17 tires Is the any damage for bearings after Use ?! No expierience?! If not I will do it to install 😎

Since running your spacers do you hav want issues with uneven tire wear or any other concerns from them. I’m contemplating going with some 1.75 inch cub centric

Should be mentioned, in some areas/countries, wheel spacers are illegal and your insurance company can refuse to cover you. Also they put a lot of side load on your wheel bearings, causing premature wear and failure(as do offset wheels) and so should be limited to 1" or 25mm. Also illegal in some areas is to have your tires protruding out past your fenders.

@user-vb9kd3lg1s

2 жыл бұрын

You have to be a moron if you get in trouble for having spacers, you would literally have to snitch on yourself for anyone to find out.

@Marie-kj3xf

4 ай бұрын

Welcome to Joe Biden’s America

I want these in 1.75" in Red. Great video! Have you modified or made a video on your exhaust system?

@c130aviator

3 жыл бұрын

No exhaust plans. The stock system is well designed.

Those running lights 🥺🥺🥺

Very nice video. Always learning something from you. How are you liking the headlights since it’s been a while from install?

@c130aviator

3 жыл бұрын

They are still going strong and have been reliable so far. Thanks.

@zacharycampbell4755

3 жыл бұрын

I got the headlights right after I saw his video. I really really like them. Super clean low beam line and the high beams are incredible. You can run on the DRL at night lol People have complimented them and want to know where to get them. Like Brandon said "no problems so far"

@learningtofishkeep665

3 жыл бұрын

@@zacharycampbell4755 thanks for the tips! Will get these soon then!

Hi, What would happen if I added the spacers to my 44 negative offset Fuel 20 in rims on 35's? They have a 4.5 inch back spacing. They already stick out 2 plus inches on my JL but the look of a Jeep I saw today with half its tires untucked looked insane..... I have a 2.5 in lift btw....Love the weather there...... It was 14 below here in Minnesota last week....Thanks so much...

@c130aviator

3 жыл бұрын

I would not put spacers on wheels with 4.5 inches of backspacing personally.

What brand diff covers?

I heard that if you get only 1 inch spacers, you need to cut the lug on the truck in order to fit the wheels? is this true?

where does the rubbing was?

Nice ride. I also use spacers on my 2018 Sport. I like your video/instructions but when it came to the rear drivers side by no means should you have to kick a spacer into place. If it doesn't slide on with little effort it's more likely than not causing more stress on the lugsBut I also re torque my lugs every time I change oil/rotate tires

@c130aviator

3 жыл бұрын

The front pass side was the one I had to kick on. Its a sign of tight tolerance in the machining process and then a layer of thin anodized thickness makes it tight to the thousandths. This is completely normal and not stressing the lugs.

@kennethdawsonjr2723

3 жыл бұрын

ok

@GulongRanger

Жыл бұрын

What’s the size of the spacers you put?

So are these still good today?

What are the specs of these wheels? Thanks!

So does the spacer size dictate whether or not the original lug studs poke out of the spacer which doesn’t allow the wheel to sit flush against the spacer? For example I’m not sure what size spacer you used, probably would have been helpful to clarify but say it was only an inch and a half, wouldn’t the original lug studs be longer than the base of the spacer?

@c130aviator

3 жыл бұрын

I may have missed understood you. At 1.5 inches the lugs won't stick out. You are correct I should have clarified that a bit. Don't go too short or you loose strength in the studs. 1.5 is a small as I would go.

@farooqkamal

Жыл бұрын

@@c130aviator I have a 22 JT, I use the 1.50" and they do stick out and rub on the rim. Now I think I will experiment with 2".

If I got some 1.5 in spacers, do you think I’d have to get my tires rebalanced or adjusted again?

@c130aviator

9 ай бұрын

No, don't waste your money.

Can you use blue locktite instead of red?

@ichbinfertig8578

6 ай бұрын

I would use what the manufacturer recommends. They come with RED loctite in the kits.

I've read pros and cons for red locktite.

Do you have a lift and if so, how much is it lifted?

@c130aviator

3 жыл бұрын

I have not made a lift video but I need to. I have the mopar lift, fox shocks, 3/4 spacer on the front. Mopar control arms. Jks disconnects, rock krawler front track bar. And a few other things like synergy brace, synergy relocation bracket, and Fox stabilizer

Next Video: Lift a Mojave and slap some 35s on it! 😜 Hafa adai brother!

@c130aviator

3 жыл бұрын

Yas!

What size tires are you running?

@c130aviator

3 жыл бұрын

37x12.50R17

Brandon who’s shop you were working in they know that you armed forces/mechanic/pilot?

@c130aviator

3 жыл бұрын

This is the Air Base auto shop, you can rent the lift bay for 10 dollars. They have tools but I bring my own.

@miguelchacon1745

3 жыл бұрын

@@c130aviator that is so cool...you did your lift there?

@c130aviator

3 жыл бұрын

@@miguelchacon1745 yes

Are you supposed to give the nuts 100lbs all at once or should you go in increments? Like first star pattern 20lbs, second star pattern 60 lbs and last star pattern 100lbs?

@jessemartinez4601

2 жыл бұрын

No, torquing in a star pattern is sufficient

@positronikiss

2 жыл бұрын

@@jessemartinez4601 tenkius!

I wouldn’t install wheel spacers, I just think that your asking for trouble but that’s my opinion

put 1.75 spacers on rear only jeep jl 6 months later rear diff shot 80k miles......coincidence?

@c130aviator

18 күн бұрын

@jergernice1 jl is not built as well as the jt. Probably the weaker axles they put in them. All part of the jeep life. I have been running these type of spacers since 2004. Never had an axle problem. Ever.

Torque the wheels also, don’t use an impact gun

@c130aviator

4 ай бұрын

Watch the whole video

DO buy correct offset wheels. DONT ever use wheel spacers under any circumstance!